• 한국세라믹학회지
• /
• 제28권4호
• /
• pp.305-314
• /
• 1991

This study was conducted to research the formation and the color development of NiO-ZnO-Fe2O3-TiO2-SnO2 system for the purpose of synthesizing the spinel pigments which are stable at high temperature. After preparing ZnO-Fe2O3 as a basic composition, {{{{ chi }}NiO.(l-{{{{ chi }})ZnO.Fe2O3 system, {{{{ chi }}NiO.(l-{{{{ chi }})ZnO.TiO2 system, and {{{{ chi }}NiO.(l-{{{{ chi }})ZnO.SnO2 system were prepared with {{{{ chi }}=0, 0.2, 0.5, 0.7, 1 mole ratio respectively. The manufacturing was carried out at 128$0^{\circ}C$ for 30 minutes. The reflectance measurement and the X-ray analysis of these specimens were carried out and the results were summarized as follows. 1. In the specimens which included NiO, it was difficult for the spinel structure to be formed. 2. As increasing the contents of NiO and Fe2O3, all the groups which were yellow or green colored changed to brown. 3. NiO-ZnO-Fe2O3 system and NiO-ZnO-TiO2 system formed the spinel structure and the illmenite structure appeared in NiO-TiO2 system.

• 한국세라믹학회지
• /
• 제33권8호
• /
• pp.895-900
• /
• 1996

수산염볍으로 Ba(Ti1-xSnx)4O9 분말을 합성하였다. Ti자리에 Sn이 치환되면 생성된 BaTi4O9은 고용체를 형성하기 때문에 안정화되었다. BaTi4O9 결정상의 생성을 위한 최적 고용량은 0.16mole이었으며, 그 이상 첨가시는 BaTi4O9 결정 성장을 억제하였다. 0.16mole Sn을 첨가하여 135$0^{\circ}C$에서 30분 소결하였을 때 긴 막대형의 결정이 가장 잘 발달하였고, 이때 Q값이 가장 높았다. 그러나 Sn 첨가량이나 소결 유지시간을 변화시켜도 유전율은 거의 일정하였다.

• 한국광물학회지
• /
• 제5권1호
• /
• pp.1-5
• /
• 1992

太白山地區의 主要 망간鑛床에서 産出하는 酸化망간 鑛物들은 一次的으로 생성된 炭酸망간 또는 珪酸망간의 表成風化作用에 依하여 生成되었다. 이들 酸化망간 鑛石의 生成에 관여된 地質作用에는 溶解作用, 酸化作用, 運搬作用, 沈澱作用, 晶出作用 및 再結晶作用 等이 있다. 그러나 箇箇의 酸化망간 鑛物 生成은 交代作用, 溶液으로부터의 晶出作用 및 固體狀態에서의 晶出, 및 再結晶作用 等에 依하여 이루어졌다. 이들 鑛物生成作用에 依하여 多樣한 名種 鑛石의 組職이 形成되었으며, 母鑛石의 鑛物組成과 風化環境에 따라 特徵的인 鑛物 및 鑛物共生關係가 形成되었다. 그러나 一般的으로 風化殘留鑛床 중의 酸化망간 鑛物들은 $Mn^{2+}{\to}Mn^{3+}{\to}Mn^{4+}$의 方向으로 生成되었다.

• 한국태양에너지학회 논문집
• /
• 제29권4호
• /
• pp.34-40
• /
• 2009

$1m^3$ hydrate of pure methane can be decomposed to the maximum of $216m^3$ methane at standard condition. If these characteristics of hydrate are reversely utilized, natural gas is fixed into water in the form of hydrate solid. Therefore, the hydrate is considered to be a great way to transport and store natural gas in large quantity. Especially the transportation cost is known to be 18-24% less than the liquefied transportation. In the present investigation, experiments and theoretical calculation carried out for the formation of methane hydrate in NaCl 3.5wt% solution. The results show that the equilibrium pressure in seawater is more higher than that in pure water, and methane hydrate could be formed rapidly during pressurization if the subcooling is maintained at 9K or above in seawater and 8K or above in pure water, respectively. Also, amount of consumed gas volume in pure water is more higher that in seawater at the same experimental conditions. Therefore, it is found that NaCl acts as a inhibitor.

• Bulletin of the Korean Chemical Society
• /
• 제30권2호
• /
• pp.373-377
• /
• 2009

A pathway for the formation of normal $CoAl_2O_4$ particles is suggested. The optimal amount of malonic acid was determined, and the characteristics of the obtained powders were investigated. Normal $CoAl_2O_4$ powders were prepared using solutions of malonic acid and metal nitrates. X-ray diffraction, Brunauer-Emmett-Teller (BET) and scanning electron microscope (SEM) measurements, as well as Fourier transform infrared (FTIR) and ultraviolet/visible (UV-Vis) spectroscopy were carried out. Normal $CoAl_2O_4$ crystallites were formed by a solid state reaction between $CoAl_2O_4$ and amorphous aluminum oxide. The optimal molar ratio of malonic acid to the nitrate anions present in the initial solution was found to be 0.30~0.35. The particles were composed of agglomerates of primary particles. The primary particles were 40 nm in size. This size was relatively constant regardless of the preparation temperature. However, the size of the agglomerated particles increased to 220 nm with increasing temperature.

• 한국표면공학회지
• /
• 제31권3호
• /
• pp.142-150
• /
• 1998

Stainless steel is being used widely for various purposes due to its good corrosion resistance. There has been much research to produce colored stainless steel by several methods such as anodizing and ion plating. In this experiment, we coated TiN(C,O,H)films SUS304 substraate with the DC magnetron spttering system made by Leybold Heraeus and studied the interlater structure and abhesive strength of the films as a function of additional gases, acetylene, hydrogen and oxygen. When the acetylene gas was added into the chamber, the specimen with the interlayer phase had good adhesion due to the toughness of the $\gamma'-Fe_4N$ plase induced from a solid solution of carbon atoms, while low adhesion appeared on the specimen of the non interlayer phase. The formation of the interlayer phase($\gamma'-Fe_4N$) was due to hydrogen embrittlement and internal stress induced by $\gamma'-Fe_4N$ formation in the interlayer. We could fine the interlayer phase ($\gamma'-Fe_4N$) at the interface between the film and the substrate of the TEM image when $\gamma'-Fe_4N$ was detected by the X-ray duffraction metheod.

• 한국주조공학회지
• /
• 제39권3호
• /
• pp.33-43
• /
• 2019

In this study, the effects of Zn additions on the mechanical properties of Al-Si-Mg-Cu alloys were investigated by increasing the amount of Zn up to 8wt.%. As the Zn content was increased up to 6 wt.%, the yield strength and elongation changed linearly without any significant changes in the size and shape of the main reinforcement phase. However, it was confirmed by SEM observation that the Mg-Zn phase formed between the reinforcement phases when the amount of Zn added exceeded 7wt.%. A Mg-Zn intermetallic compound formed between the $Mg_2Si$ phase, becoming a crack initiation point under stress. Thus, the formation of the Mg-Zn phase may cause a sharp decrease in the elongation when Zn at levels exceeding 7 wt.%. It was also found that the matrix became more brittle with increasing the Zn content. From these results, it can be concluded that the formation of the Mg-Zn intermetallic compound and the brittle characteristics of the matrix are the main causes of the remarkable changes in the mechanical properties of this alloy system

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.283-283
• /
• 2013

Because of beautiful glossy and color, the value of gold leverage is very high in Europe. To improve the quality of gold alloys, we performed heat treatment on 14 K white gold alloys by variously changing age-hardening conditions. Age-hardening behavior and the related phase transformation changes were studied to elucidate the hardening mechanism of 14 K white gold alloy. For solid solution treatment [ST], casted gold alloy specimens were treated at high temperature ($750^{\circ}C$) for 30 minutes, and the specimens dropped to water to quench them. For Age-hardening treatment [AT], the specimens were treated at various temperatures ($250{\sim}300^{\circ}C$). After the heat treatment, we observed the phenomenon to increase hardness from 126 Hv to 166 Hv by Vicker's hardness tester. Through electron probe micro-analysis (EPMA) mapping analysis, we investigated that irregular particles were changed uniformly. In the SEM and OM images, two phases of matrix and particle-likestructures were observed, and the precipitation of these elements from the matrix progressed during age-hardening. By transmission electron microscope and X-ray diffraction observation, it was revealed that the formation of the Au3Cu superstructure contributed to the age-hardening at $270^{\circ}C$ in the gold alloy. After the heat treatment, this analysis shows that casted gold alloys were to improve hardness and to moderate surface defects at specific temperatures and duration.

• 한국분말재료학회지
• /
• 제15권3호
• /
• pp.239-243
• /
• 2008

Ni-W(1-5 at.%) alloy rods were made by powder metallurgy process including powder mixing, compacting and subsequent sintering. Ni and W powder of appropriate compositions were mixed by a ball milling and isostatically pressed in a rubber mold into a rod. The compacted rods were sintered at $1000^{\circ}C-1150^{\circ}C$ at a reduced atmosphere for densification. The lattice parameters of Ni-W alloys were estimated by a high resolution neutron powder diffractometer. All sintered rods were found to have a face centered cubic structure without any impurity phase, but the diffraction peak locations were linearly shifted with increasing W content. The lattice parameter of a pure Ni rod was $3.5238{\AA}$ which is consistent with the value reported in JCPDS data. The lattice parameter of N-W alloy rods increased by $0.004{\AA}$ for 1 atomic % of W, which indicates the formation of a Ni-W solid solution due to the substitution of nickel atoms by tungsten atoms of larger size.

• 청정기술
• /
• 제8권1호
• /
• pp.53-59
• /
• 2002

공침-액상산화법으로 $Cu-CeO_2$ 촉매를 제조하여 선택적 산화반응에 대한 활성을 실험적으로 고찰하였다. $Cu-CeO_2$ 촉매는 일산화탄소의 선택적 산화반응에 우수한 활성을 보였으나, 구리의 담지량과 촉매 활성 사이의 일정한 상관관계를 찾을 수 없었다. 또한 구리의 담지량이 증가함에 따라 $CeO_2$의 세공 구조가 변하는 것을 확인할 수 있었으며 이는 Cu와 $CeO_2$가 고용체를 형성하기 때문으로 확인되었다. 촉매 전처리인 환원처리를 통한 Cu와 $CeO_2$의 고용체 형성이 촉매의 일산화탄소의 선택적 산화반응에 대한 활성을 증가시켰다.