• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.575-579
• /
• 2006

Solid electrolyte interface is formed on a carbon electrode used as an anode in Li-ion battery, which can be of $Li^{+}$ intercalation/deintercalation during the first cycle. The passivation film formed by a solvent decomposition during the initial charge process affects cell performance and it was one of the main reason of an initial irreversible capacity. This paper describes the use, for the first time, of $Li_2CO_3$ as the additive for the formation of a passivation film on the carbon surface to suppress the initial irreversible reaction. Chronopotentiometry, cyclic voltammetry, and impedance spectroscopy were used to investigate the effects of the $Li_{2}CO_{3}$ additive. Scanning electron microscopy, energy dispersive X-ray analysis, and X-ray diffraction were also used to monitor changes in the surface morphology and composition of the passivation film formed by solvent decomposition and the precipitation of $Li_{2}CO_{3}$. The addition of $Li_{2}CO_{3}$ to a solution of 1 M $LiPF_{6}$/EC:MA (1:3, v/v) resulted in a decrease in the initial irreversible capacity and it was due to the suppression of the solvent decomposition on the electrode surface.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.40-48
• /
• 2010

It was investigated that effects of NaOH concentration on synthesis of mesoporous materials using municipal solid waste incinerator ash slag (MSWI-ash slag). In order to increase the purity and maximize the amount of extracted Si content the raw MSWI-ash slag was mechanically activated. Extraction of Si from the MSWI-ash slag was carried out by alkali treatment using concentrated NaOH solution, which varied from 1M to 4M. Physical properties (i.e., pore size, specific surface area and total pore volume) of the synthesized mesoporous silica were also evaluated as a function of NaOH concentration via BET, SEM, TEM and small-angle X-ray scattering analyses. Over the entire range of NaOH concentration investigated (i.e., 1-4M), the synthesized mesoporous materials were determined to be SBA-15, which exhibited a hexagonal structure with the pore size of approximately 7 nm. On the other hand, specific surface area and total pore volume increased with NaOH concentration up to 3M while the values decreased at 4M, indicating that the optimal NaOH concentration for the synthesized mesoporous silica was approximately 3M. Further comparison analysis between two conditions (3M versus 4M) showed that the decrease in two physical properties at 4M NaOH concentration was likely due to the potential inhibition by excess Na ions on the formation of mesophase and the consequent increase of pore wall thickness by remaining Si ions.

• Journal of Conservation Science
• /
• v.35 no.5
• /
• pp.480-493
• /
• 2019

In this study, the method for processing glue and glue-alum sizing from the dancheong ground treatment was evaluated with respect to weather resistance, and its effect on the conservation of dancheong was analyzed. Viscosity and pH of the glue and glue-alum specimen were measured and classified into three categories(none layer, glue layer, and glue-alum layer), which were further classified according to low concentration(four times for 2%) and high concentration(once for 10%). The base layer formation was subsequently classified into three categories based on pigment adoption, namely, Noerok(celadonite), Seokganju(terra rossa), and Jangdan(red lead). The completed specimen was subjected to a changing-environment experiment for evaluating weather resistance and observing the surface. Color variations were analyzed before and after the experiment. The results indicate that glue-alum sizing comprising 5% alum or 7% alum has strong acidity that can affect the life of dancheong, and the high level of 7% alum makes it difficult to create a solid coating layer. After ultraviolet irradiation, the specimen with 7% alum changes its color to yellow. Furthermore, after moisture absorption and drying, cracks can be observed on the entire specimen surface that corroborate the physical change. Additionally, gas-based corrosion causes marginal surface changes. Hence, the formation of a stable coating layer can be achieved by incorporating a low concentration glue solution that is almost neutral, and the application of glue-alum sizing having 2% concentration can aid in the conservation of dancheong.

• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.897-907
• /
• 1991

This study was conducted to research the formation and the color development of CoO-ZnO-Fe2O3-TiO2-SnO2 system for the purpose of synthesizing the spinel pigments which are stable at high temperature. After preparing CoO-ZnO-Fe2O3, in which CoO causes the color, as a basic composition, $\chi$CoO.(1-$\chi$)ZnO.Fe2O3 system, $\chi$CoO.(1-$\chi$)ZnO.TiO2 system and $\chi$CoO.(1-$\chi$)ZnO.SnO2 system were prepared with $\chi$=0, 0.2, 0.5, 0.7, 1.0 mole ratio respectively. The manufacturing was carried out at 128$0^{\circ}C$ for 90 minutes. These specimens were analyzed by the reflectance measurement and the X-ray diffraction analysis and the results were summarized as follows: 1. All of the specimens formed the spinel structure and were colored with stable yellow or blue. 2. As the content of CoO and Fe2O3 in the specimens being increased, the reflectance of each specimen was measured becoming lower and the colors were changed from yellow to greyish blue and from blue to dark blue. 3. As the substituting amount of Co2+ ion for Zn2+ ion in $\chi$CoO-ZnO-TiO2-SnO2 system being increased, the colors were changed from blue to greyish blue. The colors were changed from yellow to grayish green owing to the tetrahedral Co2+ ions being increased, the octahedral Co2+ ions being decreased with increasing the amount of Sn4+ ions. 4. CoO-ZnO-Fe2O3-TiO2-SnO2 system, in which Zn2+ was substituted with Co2+ and Fe3+ was substituted with Ti4+ and Sn4+, easily formed the spinel structure without regard to the amount of substitution or the ion owing to the selectivity of the coordination number: 4 of Zn2+, 4 of Co2+, 6 of Fe3+ or 6 of Ti4+ and Sn4+.

• Journal of the Korean Chemical Society
• /
• v.46 no.1
• /
• pp.26-36
• /
• 2002

A solid-state reaction of $MoO_3$ with as-synthesized H-SAPO-34 generated paramagnetic Mo(V) species. The dehydration resulted in weak Mo(V) species, and subsequent activation resulted in the formation of Mo(V) species such as $Mo(V)_{5c}$ and $Mo(V)_{6c}$ that are characterized by ESR. The data of ESR and ESEM show the oxomolybdenum species, to be $(MoO_2)^+$ or $(MoO)^{3+}$. The $(MoO_2)^+$ species seems to be more probable. Since H-SAPO-34 has a low framework negative charge, $(MoO)^{3+}$ with a high positive charge can not be easily stabilized. A solution reaction between the solution of silico-molybdic acid and calcined H-SAPO-34 resulted in only $(MoO_2)^+$ species. A rhombic ESR signal is observed on adsorption of $D_2O$, $CD_3OH$, $CH_3Ch_2OD$ and $ND_3$. The Location and coordination structure of Mo(V) species has been determined by three-pulse electron spin-echo modulation data and their simulations. After the adsorption of methanol, ethylene, ammonia, and water for MoH-SAPO-34, three molecules, one molecule, one and one molecule, respectively, are directly coordinated to $(MoO_2)^+)$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.4
• /
• pp.175-180
• /
• 2011

The doping effect of Cu in the Sr-doped lanthan manganites (LSM) has been investigated in terms of structural analysis and thermal expansion coefficient (TEC). The $La_{0.8}Sr_{0.2}Mn_{1-x}Cu_xO_3$ ($0{\leq}x{\leq}0.3$) were prepared by solid state reaction method and their crystal structure and TEC were measured. A decrease in the lattice parameters and the TEC were observed with increase eu content, whereas they were decreased for x = 0.3. For $0{\leq}x{\leq}0.2$, the decrease of the lattice parameter and the TEC with increase Cu content were attributed to the reduction of ionic radius of Cu ions due to the presence of $Cu^{3+}$ ions. For x = 0.3, however, the increase was originated from the formation of oxygen vacancies due 10 the presence of $Cu^{2+}$ and $Mn^{4+}$.

• Journal of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.645-652
• /
• 1991

The stability constants$(K_f)$ of the complexes of some transition and post-transition metal ions (Co(Ⅱ), Ni(Ⅱ), Cu(Ⅱ), Zn(Ⅱ), Cd(Ⅱ), Pb(Ⅱ), Hg(Ⅱ)) with $N_2O_3$-donor macrocyclic ligand, 1,15-diaza-3,4 : 12,13-dibenzo-5,8,11-trioxacyclooctadecane ($NtnOdienH_4$), have been determined by potentiometry in aqueous solution at $25^{\circ}C$. Log $K_f$ values of the complexes were : Co(Ⅱ): 3.83, Ni(Ⅱ) : 4.56, Cu(Ⅱ) : 7.74, Zn(Ⅱ) : 4.98, Cd(Ⅱ) : 3.91, Pb(Ⅱ) : 6.65, and Hg(Ⅱ) : 14.87. The order of stabilities of transition metal complexes was the same as the natural order of stability proposed by Williams-Irving. In post-transition metal complexes, the order of stabilities was Cd(Ⅱ) < Pb(Ⅱ) < Hg(Ⅱ), and the covalent character in metal ion-donor atoms bonds appeared a dominant factor in the stability. In methanol solution, each metal ion forms 1 : 1 complex, while Ni(Ⅱ) ion forms both 1 : 1 and 1 : 2 complexes. It was confirmed by $^1H-$ and $^{13}C-$NMR spectral study that the nitrogen atoms in the ligand were major contributors for the complexation of post-transition metal ions with the ligand. It was shown, by elementry analysis, electrical conductivity and magnetic susceptibility measurements, and spectral analysis, that solid Cu(Ⅱ)-and Zn(Ⅱ)-complexes have a distorted octahedral and a tetrahedral structure, respectively.

• Resources Recycling
• /
• v.27 no.2
• /
• pp.24-31
• /
• 2018

In this study, waste ITO target is dissolved into hydrochloric acid to generate a complex indium-tin chloride solution. Nano sized ITO powder with an average particle size below 30 nm are generated from these raw material solutions by spray pyrolysis process. Also, in this study, thermodynamic equations for the formation of indium-tin oxide (ITO) are established. As the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$, the proportion and size of the spherical droplet shape in which nano sized particles aggregated gradually decreased, and the surface structure gradually became densified. When the reaction temperature was $800^{\circ}C$, the average particle size of the generated powder was about 20 nm, and no significant sintering was observed. At a reaction temperature of $900^{\circ}C$, the split of the droplet was more severe than at $800^{\circ}C$, and the rate of maintenance of the initial atomized droplet shape decreased sharply. The average particle size of the powder formed was about 25 nm. The ITO particles were composed of single solid crystals, regardless of reaction temperature. XRD analysis showed that only the ITO phase was formed. Remarkably, the specific surface area decreased by about 30% as the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.71-75
• /
• 2012

In this study, silver nanoparticles (AgNPs) have been prepared by using aqueous $AgNO_3$ solution in the poly(vinyl alcohol) (PVA) hydrogels. PVA powders were dissolved in deionized water, and then irradiated by gamma-ray with a radiation dose of 50 kGy to make hydrogels. PVA hydrogels were dipped into 0.01 and 0.05 M $AgNO_3$ solution for 1 h respectively. After that, the swollen hydrogels were irradiated by gamma-ray at various doses to form AgNPs. UV-vis analysis indicated that the concentration of Ag NPs was enhanced by increasing absorbed dose and the concentration of $AgNO_3$. FE-SEM measurements provided further evidence for the successful formation of Ag NPs in PVA hydrogels. Also, the antibacterial effect of PVA hydrogels stabilized AgNPs against Gram-negative bacteria (S.aureus and E.coli) in liquid as well as on solid growth media has been investigated. The AgNPs consolidated in PVA hydrogel networks have an excellent antibacterial effect.

• Journal of Powder Materials
• /
• v.9 no.6
• /
• pp.394-408
• /
• 2002

Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.