• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.2
• /
• pp.38-51
• /
• 2018

This study was carried out to improve the performance characteristics of nozzleless boosters that are used in ramjet boosters. A propellant using Zr as the metal fuel was developed, which provided a higher density than the propellant using Al as the metal fuel. The developed propellant was cast using the nozzleless booster and a ground test was carried out by varying the length-to-diameter ratio (L/D ratio) of the propellant. From a comparison between the performance characteristics of propellants using Zr and Al, it was proved that the performance of the propellant using Zr is higher than that of propellant using Al, except for the specific impulse, under all tested conditions. As the length-to-diameter ratio was increased, the specific impulse of the propellant using Zr was decreased by 88% compared with that of the propellant with Al. However, because of the density difference between the propellants, the impulse density of the propellant with Zr was higher than that of the propellant with Al under all tested conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1355-1360
• /
• 2013

A cracked solid propellant would have failure or fracture of rocket because of excessive combustion according to increase of burning area, therefore it is important to evaluate the fracture toughness of solid propellant. A procedure is used to investigate the material under a range of test temperatures between -60 and $60^{\circ}C$, three kind of specimen thickness, 4, 12.5 and 24.5 mm to determine the effect of two parameters on the fracture toughness. A center cracked tension (CCT) specimen is used in these tests, which were conducted using INSTRON 5567 testing machine and environmental chamber to evaluate the fracture toughness. The experimental results show that the fracture toughness tends to decreases with an increase in the temperature, and the effect of thickness indicates that the fracture toughness is highest at 12.5 mm under various temperatures except $-60^{\circ}C$. It is found that the fracture toughness of solid propellant is changed due to glass transition behavior around $-60^{\circ}C$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.6
• /
• pp.581-586
• /
• 2008

The MEMS solid propellant thrusters have very low thrust level for applying to the propulsion system of micro/nano satellites or the side jet thruster of smart bombs. In this research, the fabrication possibility of planar type MEMS solid propellant thrusters that have enlarged burning surface area was examined and the safety of the structure of thruster during the firing test was confirmed. The performance of a micro igniter which is the key component of the MEMS solid propellant thruster was estimated by the ANSYS Icepak and evaluated by the experiment. Finally, the thrust was measured by the micro force sensor. The levels of thrust were 300, 600 mN in the case of K=15, 20.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.239-245
• /
• 2006

Ultrasonic inspection method is more profitable than X-ray radiographic inspection in cost and effect of defect detection such as dis-bond, damage, and it does'nt need special constructions and can be possible real time inspection with safety. This report explains the experiment and analysis of ultrasonic property of solid propellant and the inspection methods of propellant/liner dis-bond by inside or outside inspection, and of propellnat micro crack by damage. At result, ultrasonics has big attenuation$(6\sim8db/cm)$ in solid propellant, and it. can be possiblle to detect the defect of propellant/liner dis-bond by inside or outside inspection. And also it can be possible to detect the propellant micro crack caused by damage by using ultrasonic attenuation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.2
• /
• pp.18-25
• /
• 2017

The study for the combustion characteristics of propellants for nozzleless boosters was carried out. The metal fuels of Al and Zr were introduced into solid propellant formulations in order to enhance the density-specific impulse and the high burning rate with low pressure exponent was investigated as the major combustion characteristic of propellant to design nozzleless boosters. The burning rate of Zr-containing propellant was higher than Al-containing propellant and, $13{\mu}m$ Zr-containing propellant exhibited the burning rate of 35 mm/s (at 1000 psi)and pressure exponent of 0.3282. The benefit of using Al and Zr-containing propellant into nozzleless boosters was demonstrated in these results.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.7-10
• /
• 2009

The development and evaluation of solid propellant were performed for the turbopump pyro starter, which start up the liquid propellant rocket engine for the Space Launch Vehicle (SLV). Requirements for the turbopump pyro starter propellant include the production of low flame temperature, low burning rate and nontoxic gas to protect the mechanical corrosion or air pollution. This study describes the development of the solid propellant composition which is based on PCP binder. DHG (Dihydroxy glyoxime), which has advantages of oxygen balance and ignition, was used as coolant. The mechanical properties and burning rate of the propellants were measured. Finally, static fired test was performed to prove the possibility of development.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.128-130
• /
• 2017

$NaBH_4$ was added to improve the water reactivity of aluminum powder as a solid propellant for underwater propulsion. Aluminum powders showed different combustion characteristics depending on the amount of $NaBH_4$ added. When $NaBH_4$ was added, it was burned by reaction with water even at a temperature much lower than the boiling point. In this study, it was confirmed that $NaBH_4$ is an effective additive to accelerate the vapor reaction with Al powder.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.41-47
• /
• 1999

The burning rate of solid propellant is one of the key parameter associated with the dynamic characteristics of combustion and the combustion performances. In the AP propellants, the evaporation on the reacting surface as well as the decomposition of the propellant is of great importance in determining the overall burning rate. In this study, a theoretical analysis was conducted to obtain the expression for burning rate in the steady state combustion with the energy and species equations in the condensed phase when the radiative heat flux partially contributes to the total heat transfer to the propellant surface.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.431-436
• /
• 2008

T-burner tests of an Al/HTPB propellant in conjunction with a Pulsed DB/AB Method were conducted to find an acoustic amplification factor. Aluminum-free and aluminum-heavy propellants were examined. Instant surface ignition was successfully made by the use of a supplementary propellant of fractionally higher reaction rate. With the presence of higher aluminum concentration in the propellants, the pressure perturbations were promptly damped down and the pressure fluctuations were no longer dispersive. Addition of aluminum particles into the propellant was advantageous for stabilizing pressure-coupled unstable waves.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.6
• /
• pp.28-33
• /
• 2022

In this study, the curing characteristics of commonly used Hydroxyl terminated polybutadiene(HTPB)-based solid propellant according to the curing temperature and Equivalent ratio change were investigated. In addition, the effect of curing reaction according to their ratio and content in the Triphenyl bismuth(TPB), Maleic anhydride(MA) and Magnesium oxide(MgO) catalyst systems was confirmed. Finally, moisture was added for each propellant mixing process to check the effect of moisture on propellant curing.