• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1992년도 가을학술발표회 논문집
• /
• pp.11-26
• /
• 1992

An attempt has been made to summarize some of the unique geotechnical problems encountered during construction of a few large man-made islands recently completed off the coast of Osaka Bay, Japan. Large settlements appear to be the most serious problem both during and after construction. Settlements due to consolidation of a thick layer of soft alluvial clay that constitutes seabed seem to virtually cease within a relatively short period of time when vertical drains are installed adequately prior to fill placement. Settlements due to compression of underlying thick diluvial deposits consisting of layers of stiff clays interbedded with coarse-grained soils, however, continue over a prolonged period of time and call for special provisions for structures built on the artificial islands to cope with relatively large future settlements. Although accurate settlement prediction is not possible, it is both technically and economically feasible, nevertheless, to construct large-scale islands. Partjcularly attractive and promising is creation of sizable new areas for various purposes, immediately adjacent to highly-developed, densely-populated cities situated along the coast such as those around Osaka Bay.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1997년도 Lecture Notes by Two Distinguished Scholars
• /
• pp.1.2-22
• /
• 1997

Anisotropic behaviour in soils and soft rocks may be either fabric of stress related ultra in practice is invariably a combination of both. Theoretical studies in the paper include tile iMluence oil untrained strength of assuming both the critical state and Mo21r-Coulomb concepts to hold, and the influence of elastic anisotropy oil predicted undrained effective stress paths. The predictions stemming from these theoretical concepts are examined in the light of evidence from triaxial compression and extension tests oil laboratory prepared, compacted and natural clays and from triaxial compression tests on clay shales. The experimental studies also show the Buence of sample orientation on untrained snear strength, as wen as the iIBluence of anisotropy old the effective stress angle cishearing resistance and of stress patn on measured stiffness.

• 한국지반환경공학회 논문집
• /
• 제3권3호
• /
• pp.15-25
• /
• 2002

투수계수는 연약점토의 기본 공학 특성 중 하나로서, 투수계수 값은 점토의 압밀과정뿐만 아니라 토양 내 오염물질의 이동에도 관계된다. 일반적으로 압밀이 진행되는 동안 간극비의 감소로 인해 점토의 투수계수 값은 감소하게 된다. Kozeny와 Carman 이후의 많은 연구자들이 다음의 관계로 간극비와 투수계수의 관계를 제안하였다. (1) log e - log k(1+e), (2) e - log k, (3) log e - log k. 본 연구에서는 대표적 국내 해성점토인 김해점토와 군산점토에 대하여 일정변형률(CRS) 압밀시험 수행하였다. 시험결과로부터 위의 관계식들은 군산점토와 김해점토에 모두 적용 가능한 것으로 나타났으며, 김해점토의 경우 경험적 관계식인 $C_k=0.5e_o$를 잘 만족하고 있으나 군산점토의 경우는 그렇지 않은 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.898-905
• /
• 2005

The settlement of embankment on soft clay includes shear settlement due to shear deformation. Even though the consolidation settlement is not related to lateral displacement, but shear settlement makes the embankment unstable because it deforms ground and decreases the ground strength. In order to determine the shear deformation behaviour during embankment construction, 3 cases (1B, 2B, and 3B) of rapid undrained loading tests on soft clays were performed. Shear settlement is consist of elastic settlement, plastic settlement and viscous settlement. Elastic settlement isn't considered because the range is small, therefore the first is the range of plastic displacement, and the second is that of viscous displacement in the displacement-time curve for each loading stage. After determining that the change in the inclination of the viscous displacement range is larger than in the plastic displacement range after the ground failure occurs for the loading stage, the stability management methods were suggested considering that it is hard to divide the plastic displacement range and the viscous displacement range. The stability management method was based on the ratio of the plastic displacement range's inclination and the viscous displacement range's inclination. A stability management method based on the ratio of the total inclination for each loading stage compared to the whole inclination in the initial loading stage was also recommended.

• 한국지반공학회논문집
• /
• 제22권11호
• /
• pp.37-45
• /
• 2006

1970년대 중반부터 bender elements를 이용하여 흙 공시체의 전단파 속도를 측정하는 기술이 발전되어 왔다. 얇은 피에조 세라믹판과 탄성 매질을 겹쳐서 만든 bender elements는 삼축입축시험장치의 저판(base)와 top cap에 설치하여 액츄에이터와 트랜스듀스로 각각 사용하여 공시체의 전단파 속도를 측정하고 있다. bender elements를 현장에 적용하는 예비 단계로, 최적의 벤더 제작과 기하학적 배치에 대한 연구를 실내 카올리나이트 토조에서 수행하였다. 이 예비시험에서 개발된 bender element를 사용하여 갯벌에서 크로스홀 방식과 인홀 방식으로 탄성파 시험을 수행하였다. 일련의 bender elements를 깊이 2m까지 삽입하여 현장시험의 적용성을 확인하였다. 추후 깊은 심도까지 삽입할 수 있는 맨드렐(mandrel)과 관입장치를 개발하여 연약지반의 탄성파 속도 측정 장치 개발을 완성하고자 한다.

• 한국지반공학회논문집
• /
• 제30권2호
• /
• pp.65-76
• /
• 2014

해안지역의 연약지반을 개량하기 위하여 연약지반 위에 모래를 포설하거나 모래다짐말뚝을 시공할 경우 점토와 모래가 서로 섞이는 경우가 많으며, 풍화된 사면의 표층에도 모래나 자갈 섞인 세립토가 많이 존재한다. 본 연구에서는 이와 같은 혼합토에 포함된 모래 함유량의 증가에 따른 점토의 액소성한계 및 전단강도 변화에 대해 연구하였다. 먼저 카올리나이트와 벤토나이트에 모래 함유량을 0, 9, 17, 23, 29, 33, 또는 50%까지 증가시키면서 액소성한계시험을 실시하였으며, 모래 함유량이 증가함에 따라 액소성한계는 감소하는 경향을 보였다. 다양한 모래 함유량을 가진 카올리나이트와 벤토나이트에 함수비를 10% 또는 20%씩 단계적으로 증가시키면서 토베인시험기를 이용하여 비배수전단강도를 측정하였다. 동일한 모래 함유량을 가진 공시체의 경우 특정 함수비에서 비배수전단강도가 급격히 감소하였으며, 공시체 내 모래 함유량이 증가할수록 배수가 발생하면서 비배수전단강도는 감소하였다. 한편 동일한 조건의 혼합토에 대한 직접전단시험을 실시하여 모래 함유량의 증가에 따른 점토-모래 혼합토의 점착력 및 내부마찰각을 측정하였다. 점토 내 모래 함유량이 증가함에 따라 점착력은 감소하였으며, 내부마찰각은 증가하는 경향을 보였다.

• 한국환경보건학회지
• /
• 제44권3호
• /
• pp.238-243
• /
• 2018

Objectives: The purpose of this study was to determine skin adhesion rate of children's modeling clay for exposure assessment. Methods: Children's modeling clays were classified into 10 categories as PVA clay, PVA soft clay, starch-based clay, foam clay, rubber clay, oil clay, muddy clay, terra clay, paper clay and slime. A total of 26 children's clay goods was selected. Moisture content (%) and hardness of clays were measured. Five adults aged 20 to 25were recruited for experiment. Gravimetric difference of modeling clay was determined after 3 minutes playing time. Skin adhesion rate ($g/min/cm^2$) was estimated bythe amount of skin adhesion per minute (g/min) and each individual's palm surface area ($cm^2$). Results: Twenty four of the 26 children's modeling clay products were adhesive to skins. Two products of foam and rubber clay were not adhered to skin. For the 24 products, the average skin adhesion rate was $5.5{\times}10^{-4}{\pm}4.0{\times}10^{-4}g/min/cm^2$. The highest skin adhesion rate was $1.3{\times}10^{-3}{\pm}4.4{\times}10^{-4}g/min/cm^2$ for paper clay. The lowest skin adhesion rate was $4.6{\times}10^{-5}{\pm}1.1{\times}10^{-4}g/min/cm^2$ for oil clay. The skin adhesion rate was increased with increase of moisture content. Adhesion rates of some clays were varied by person and testing trials. Conclusion: The study determined skin adhesion rate of children's modeling clay. The adhesion rate is useful for exposure and risk assessments and setting safety guideline to protect children's health.

• 보존과학연구
• /
• 통권21호
• /
• pp.233-271
• /
• 2000

This study has proved if there are homogeneities in crystal structures, firing temperaures and element compositions of 69 specimens for potteries and soils from Changdo, Kangjin-gun, Jinjuk-Ri in Korea and Yaezhou inChina and obtained the following results.1. XRD analyses showed that soft potteries seemed to contain ($\alpha$)quartz, feldspar, while hard potteries seemed to contain ($\alpha$-)quartz, mullite, tridymite, feldspar. Jinjuk-Ri soils consisted of clays such as Kiolinite, Montmorillonite, Muscovite, Illite and, mica and feldspar etc.2. It was estimated that the firing temperatures which are determined by crystals using XRD, ranged from $550^{\circ}C$ to $870^{\circ}C$ for soft potteries and $870^{\circ}C$ to $975^{\circ}C$ for hard potteries.3. The firing temperatures for 4-pieces of Changdo pottery were measured by using TG-DTA, and it was found that specimen No. 10 was fired at temperatures below $600^{\circ}C$, while specimens No. 14, No. 23 and No. 29 were fired at temperatures above $1000^{\circ}C$.4. It was found that the specimems for potteries and porcelains from Changdo, Kangjin-gun, Jinjuk-Ri in Korea and Yaezhou in China were apparently classified into 4 clusters. This suggests that there are no correlations between the raw materials used in each 4 regions. Among the porcelains from Changdo, there were many typologically similar ones to those from Yaezhou in China in the 9th centry, but the analyses of porcelains only from Changdo, Kangjin in Korea and Yaezhouin China showed that they were classified into 3 clusters. This suggest that there are no correlations between the raw materials used for making porcelains in Changdo, Kangjin-gun, Jinjuk-Ri in Korea and Yaezhou in China.

• 산업기술연구
• /
• 제28권B호
• /
• pp.91-99
• /
• 2008

Applicability of existing methods of predicting consolidation settlement was assessed by analyzing results of centrifuge tests modelling self-weight consolidation of soft marine clay. From extensive literature review about self-weight consolidation of soft marine clays located in southern coast in Korea, constitutive relationships of void ratio-effective stress-permeability and typical self-weight consolidation curves with time were obtained by centrifuge model experiments. For the condition of surcharge loading, exact solution of consolidation settlement curve was obtained by Terzaghi's consolidation theory and was compared with the results predicted by currently available methods such as Hyperbolic method, Asaoka's method, Hoshino's method and ${\sqrt{S}}$ method. All methods were found to have their own inherent error to predict final consolidation settlement. From results of analyzing the self-weight consolidation with time by using those methods, Asaoka's method predicted the best. Hyperbolic method predicted relatively well in error range of 2~24% for the case of showing the linearity in the relationship between T vs T/S in the stage of consolidation degree of 60~90 %. For the case of relation curve of T vs $T/S^2$ showing the lineality after the middle stage, error range from Hoshino method was close to those from Hyperbolic method. However, Hoshino method is not able to predict the final settlement in the case of relation curve of T vs $T/S^2$ being horizontal. For the given data about self-weight consolidation after the middle stage, relation curve of T vs T/S from ${\sqrt{S}}$ method shows the better linearity than that of T vs $T/{\sqrt{s}}$ from Hyperbolic method.

• Geomechanics and Engineering
• /
• 제36권6호
• /
• pp.563-573
• /
• 2024

In this study, various countermeasures used to mitigate tunnel deformations due to nearby multi-propped basement excavation in soft clay are explored by three-dimensional numerical analyses. Field measurements are used to calibrate the numerical model and model parameters. Since concrete slabs can constrain soil and retaining wall movements, tunnel movements reach the maximum value when soils are excavated to the formation level of basement. Deformation shapes of an existing tunnel due to adjacent basement excavation are greatly affected by relative position between tunnel and basement. When the tunnel is located above or far below the formation level of basement, it elongates downward-toward or upward-toward the basement, respectively. It is found that tunnel movements concentrate in a triangular zone with a width of 2 H_e (i.e., final excavation depth) and a depth of 1 D (i.e., tunnel diameter) above or 1 D below the formation level of basement. By increasing retaining wall thickness from 0.4 m to 0.9 m, tunnel movements decrease by up to 56.7%. Moreover, tunnel movements are reduced by up to 80.7% and 61.3%, respectively, when the entire depth and width of soil within basement are reinforced. Installation of isolation wall can greatly reduce tunnel movements due to adjacent basement excavation, especially for tunnel with a shallow burial depth. The effectiveness of isolation wall to reduce tunnel movement is negligible unless the wall reaches the level of tunnel invert.