• 한국안전학회지
• /
• 제32권3호
• /
• pp.15-20
• /
• 2017

This study presented the strength of the materials and parts for smart distribution board fabrication, and developed a work operation process chart for smart distribution board fabrication. This work operation process chart for smart distribution board fabrication complied with SPS-KEMC regulations, and the applicable range and object are less than 1,000 V and 1,000 Hz for the AC distribution board and less than 1,500 V for the DC distribution board. The power supply is 3 phase 4 wires ($3{\Phi}$ 4W), divided into a single phase circuit and a 3 phase circuit. In addition, the circuit was configured so that the leakage current flowing through the distribution line of the load could be monitored in real time by using the sensor module installed at the rear end of the circuit breaker. Therefore, the administrator can easily find the risk factor of the load since engineer can check the leakage current of each distribution line. In addition, if a leakage current greater than standard value flows, it is possible to generate an alarm against a short circuit and cut off the leakage current. The work operation process chart for the smart distribution board fabrication consists of the following steps: raw and subsidiary materials, sheet metal work, tube making, welding, painting, busbar fabrication, assembly and wiring, product inspection, shipment, etc. Moreover, symbols, ${\Delta}$, ${\nabla}$, ${\bigcirc}$, ${\Rightarrow}$, etc. were used according to the type of work and work progress so that workers can easily understand the progress of the work.

• 융합정보논문지
• /
• 제11권11호
• /
• pp.151-158
• /
• 2021

본 논문에서는 차세대 태양전지로 대표되는 유기, 염료 감응형, 페로브스카이트 태양전지의 최신 연구 동향과 건축, 조형예술, 의류패션 등 분야를 막론한 다양한 산업의 소재로의 과제와 활용 가능성을 분석하였다. 더불어, 웨어러블 IoT 장치와 결합하여 자연 및 인공광과 우리 몸의 움직임에 따라 생성되는 크고 작은 진동 에너지를 전기에너지로 공급하는 역할을 하게 될 '스마트 텍스타일 하이브리드 에너지 하베스팅 소자'의 새로운 미래전망과 그 가능성을 제시하였다. 차세대 태양전지와 마찰·압전소자를 융합한 '하이브리드 텍스타일 에너지 하베스팅 디바이스'는 4차 산업혁명 시대의 웨어러블 IoT 기기에 소재 자체로 결합하여 새로운 '융합 일체형 스마트 의류'로 발전할 것이다. 이 연구가 제안한 차세대 나노기술과 소자가 에너지 하베스팅 기능을 갖는 스마트 섬유 소재 분야에 적용되고, 미래 의류 산업에 융합되어 의료, 헬스케어 등 다양한 분야에 AI 서비스 제공하는 창의적인 제품으로 진화하는 패러다임의 전환점이 되길 바란다.

• Transactions on Electrical and Electronic Materials
• /
• 제15권2호
• /
• pp.96-99
• /
• 2014

We fabricated $(Li_{0.5-x}Na_xLa_{0.5})Ti_{0.8}Zr_{0.2}O_3$(LNTLZ)ceramics ($0{\leq}x{\leq}0.4$) with a perovskite structure via standard solid state synthesis. The influence of Na content on the structural and electrical properties of LNTLZ ceramics was also investigated. During XRD patterns analysis, all of the samples showed orthorhombic structure. The resistance of LNTLZ ceramics decreased as Na content increased, and the maximum activation energy shows 0.56 eV at x=0.4 at room temperature. These results indicated that LNTLZ ceramics are a candidate for use Lithium ion batteries as electrolytes.

• ETRI Journal
• /
• 제30권4호
• /
• pp.516-525
• /
• 2008

This paper proposes a compact, energy-efficient, and smart gas sensor platform technology for ubiquitous sensor network (USN) applications. The compact design of the platform is realized by employing silicon-on-insulator (SOI) technology. The sensing element is fully integrated with SOI CMOS circuits for signal processing and communication. Also, the micro-hotplate operates at high temperatures with extremely low power consumption, which is important for USN applications. ZnO nanowires are synthesized onto the micro-hotplate by a simple hydrothermal process and are patterned by a lift-off to form the gas sensor. The sensor was operated at $200^{\circ}C$ and showed a good response to 100 ppb $NO_2$ gas.

• 한국재료학회지
• /
• 제20권3호
• /
• pp.148-154
• /
• 2010

It is necessary to develop new methods to prevent catastrophic failure of structural material in order to avoid accidents and conserve natural and energy resources. Design of intelligent materials with a self-diagnosing function to prevent fatal fracture of structural materials was achieved by smart composites consisting of carbon fiber tows or carbon powders with a small value of ultimate elongation and glass fiber tows with a large value of ultimate elongation. The changes in electrical resistance of CF-GFRP/GFRP (carbon fiber and glass fiber-reinforced plastics/glass fiber-reinforced plastics) composites increased abruptly with increasing strain, and a tremendous change was seen at the transition point where carbon fiber tows were broken. Therefore, the composites were not to monitor damage from the early stage. On the other hand, the change in electrical resistance of CP-GFRP/GFRP (carbon powder dispersed in glass fiber-reinforced plastics/glass fiber-reinforced plastics) composites increased almost linearly in proportion to strain. CP-GFRP/GFRP composites are superior to CF-GFRP/GFRP composites in terms of their capability to monitor damage by measuring change in electrical resistance from the early stage of damage. However, the former was inferior to the latter as an application because of the difficulties of mass production and high cost. A method based on monitoring damage by measuring changes in the electrical resistance of structural materials is promising for improved reliability of the material.

• 한국해양공학회지
• /
• 제35권4호
• /
• pp.266-272
• /
• 2021

Mooring systems are among the most important elements employed to control the motion of floating offshore structures on the sea. Considering the use of polymer material, a new method is proposed to address the creep characteristics rather than the method of using a tension load cell for measuring the tension of the mooring line. This study uses a synthetic mooring rope made from a polymer material, which usually consists of three parts: center, eye, and splice, and which makes a joint for two successive ropes. We integrate the optical sensor into the synthetic mooring ropes to measure the rope tension. The different structure of the mooring line in the longitudinal direction can be used to measure the loads with the entire mooring configuration in series, which can be defined as SMART (Smart Mooring and Riser Truncation) mooring. To determine the characteristics of the basic SMART mooring, a SMART mooring with a diameter of 3 mm made of three different polymer materials is observed to change the wavelength that responds as the length changes. By performing the longitudinal tension experiment using three different SMART moorings, it was confirmed that there were linear wavelength changes in the response characteristics of the 3-mm-diameter SMART moorings. A 54-mm-diameter SMART mooring is produced to measure the response of longitudinal tension on the center, eye, and splice of the mooring, and a longitudinal tension of 100 t in step-by-step applied for the Maintained Test and Fatigue Cycle Test is conducted. By performing a longitudinal tension experiment, wavelength changes were detected in the center, eye, and splice position of the SMART moorings. The results obtained from each part of the installed sensors indicated a different strain measurement depending on the position of the SMART moorings. The variation of the strain measurement with the position was more than twice the result of the difference measurement, while the applied external load increased step-by-step. It appears that there is a correlation with an externally generated longitudinal tensional force depending on the cross-sectional area of each part of the SMART mooring.

• 한국전산구조공학회논문집
• /
• 제35권4호
• /
• pp.243-248
• /
• 2022

본 논문에서는 1차원 오일러 보 요소(Euler-Bernoulli Beam Element)를 이용한 회전익기 축계에 대한 중량 최적설계를 수행하였다. 회전 축계의 특성을 고려해 비틀림(Torsion)과 베어링과 같은 축지지 강성 및 플랜지(Flange) 질량을 모두 고려하였고, 동적 안전성 확보를 위해 고유치 해석을 수행하여 임계속도(Critical Speed)와 기어박스로부터 오는 치 변형 가진을 회피할 수 있도록 하였다. 축의 길이는 고정된 상태에서 두께와 반경을 조절하여 중량 최적화를 수행하였으며, 최적화 과정은 2단계로 나누어 진행하였다. 1단계에서는 비틀림 강도를 제약조건으로 하여 중량을 최적화한 후 2단계에서는 축계 안정성 확보 기준(Headquarters, U.S. Army Material Command, 1974)에 따라 축의 비틀림 강도에 대한 제약조건을 만족시키며, 축의 1차 모드가 임계속도를 회피할 수 있도록 축 1차모드와 임계속도의 차이가 최대가 되도록 최적화를 진행하였다. 주어진 1차원 보 요소를 이용하여 최적설계를 한 결과를 3차원 유한요소 모델과 실제 제작된 축게의 시험결과와 비교하여 제안된 방법을 검증하였다.

• 한국전산구조공학회논문집
• /
• 제35권6호
• /
• pp.367-374
• /
• 2022

본 논문에서는 역전파 방법 기반 자동미분법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용하였다. 응력제한조건이 있는 위상최적화문제는 특이점(singularity)과 응력의 국부성(local nature of stress constraint)문제, 그리고 설계 변수에 대한 비선형성의 문제를 포함하고 최적해를 얻기가 매우 힘들다. 특이점 문제를 해결하기 위해서 응력 완화(stress relaxation) 기법을 사용하였고, 응력의 국부성을 해결하기 위해 p-norm을 이용한 전역 응력치를 제한조건에 사용하였다. 설계 변수에 대한 비선 형성을 극복하기 위해 해석적인 방법으로 정확한 설계민감도를 구하는 것이 중요하다. 위상최적설계에서 기존에는 보조변수방법 (adjoint variable method)을 사용하여 빠르고 정확한 설계민감도를 구했지만, 설계민감도를 해석적으로 구해야 하고, 보조평형방정식을 추가로 풀어야 하는 어려움이 있다. 이를 해결하기 위해서 인공신경망에서 최적 가중치(weights)와 편차(biases)를 구할 때 쓰이는 역전파 기법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용하였다. 역전파 기법은 자동미분에 쓰이는 기법으로 목적함수나 제한조건에 대한 설계민감도를 별도의 수식유도 없이 간단하게 구할 수 있는 장점이 있다. 또한, 미분값을 구하는 역전파의 과정이 보조평형방정식을 푸는 것보다 계산시간이 빠르고 해석적 방법으로 구한 설계민감도와 같은 정확도를 보여준다.

• Tribology and Lubricants
• /
• 제29권1호
• /
• pp.39-45
• /
• 2013

Magnetorheological (MR) fluid belongs to the group of smart materials. In MR fluid, iron particles in base oil form chains in the direction of the applied magnetic field, thus resulting in a variation in the stiffness and damping characteristics of the fluid. Research is being carried out on controlling the stiffness and damping characteristics as well as the tribological characteristics of the MR fluid. In this study, the friction characteristics of MR fluid have been evaluated using three types of materials and magnetic fields of different strengths. The coefficients of friction of the three types of MR fluid are measured, and the relationship between the coefficient of friction and the strength of the applied magnetic field is obtained.

• Advances in aircraft and spacecraft science
• /
• 제7권6호
• /
• pp.517-536
• /
• 2020

The present study investigates axial vibration of a FG nanobeam using nonlocal elasticity theory under clamped-clamped and clamped-free boundary conditions. Power law, exponential law and sigmoid law are applied as grading laws to examine the effect of the material distribution on axial vibration of the FG nanobeam. A parametric study was done to examine the effect of length scale on the dynamic behavior of the structure and the results are presented. It was observed that consideration of the nonlocal length scale is essential when analyzing the free vibration of a FG nanobeam. The results of the present study can be used as benchmarks in future studies of FG nanostructures.