• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.119-128
• /
• 2004

DME(Dimethyl Ether) was directly produced from the synthesis gas using the slurry phase reactor. The catalyst for DME production prepared two types (A type; Cu:Zn:Al=57:33:10, B type; Cu:Zn:Al=40:45:15, molar ratio). It was evaluated for the effect of the reaction medium oil using the small size slurry phase reactor. DME production yield and the methanol selectivity decreased in the order: n-hexadecane oil> mineral oil> therminol oil. The long-term test of DME production was carried out using A and B type catalyst, and n-hexadecane oil and mineral oil, respectively. It was confirmed that the use of A type for the catalyst and n-hexadecane for the reaction medium oil was very useful for the viewpoint of the DME production form the synthesis gas.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.198-201
• /
• 2002

An internal finishing process by the application of magnetic abrasive machining has been developed as a new technology to obtain a fine inner surface of pipe. In this paper, a slurry circulation system was designed and manufactured. Its finishing characteristics was experimently investigated by various effective factors such as dry, water flow, oil flow with a slurry. From the experimental results, it was found that the materal removal and surface roughness were good in oil flow with slurry. The slurry circulation system is effective on the internal finishing of non-ferromagnetic pipe(SUS304).

• Resources Recycling
• /
• v.4 no.1
• /
• pp.20-24
• /
• 1995

When the slurry of water and coal which is produced from hydraulic coal mining was dehydrated by COM(Coal Oil Mixtue), the effects of flocculant were measured by light transmittance of supernatant liquid, The experimental results obtamed m this study are summarized as follows; The efficient flocculant is anionic flocculant(AllO), and in this case, the required concentration is about l00g/t. When diesel oil is used with flocculant, COM is formed in lower impeller speed than when only diesel oil is used. The amout of diesel oil required to form COM is 10% of that of coal.

• Resources Recycling
• /
• v.2 no.2
• /
• pp.39-44
• /
• 1993

This study was carried out to remove the water from low grade anthracite slurry produced at Eoryong coal mine by the oil agglomeration process. 80% of Anthracite as a coal oil mixture (COM) was separated from water by the difference of specific gravity. Then, the amount of kerosene, diesel oil, and heavy oil forming COM was 10% of the amount of sample, respectively. The recovery rate of combustibles and ash content of agglomerated anthracite were affected largely by the amount of added oil, pulp density, particle size, mixing time, and impeller speed. The recovery rate of combustibles was increased to 95% and ash content was decrea-sed from 30% to 13.5% under the optimum conditions.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 1996.11a
• /
• pp.114-117
• /
• 1996

Biodegradation potential of crude oil has been studied in liquid and soil slurry culture. Studies were performed to optimize the factors affecting metabolic activity. Arabian Light(sulfur content 1%) was used as a representative crude oil and Nocardia sp. was selected as an oil degrading microorganism based on its ability to degrade and emulsify Effects of various nutritional and environmental conditions as well as emulsification and surface tension were observed. Tentative optimization of environmental and nutritional condition were as follow; pH 8, sodium nitrate as inorganic nitrogen source, yeast extract 0.05%, phosphate concentration 0.25% and glucose addition of 1.0% (w/v basis), extent of degradation to 78 %.

• Mass Spectrometry Letters
• /
• v.2 no.2
• /
• pp.41-44
• /
• 2011

Molecular compositions of two types of heavy oil were studied using positive atmospheric pressure photoionization (APPI) Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Vacuum gas oil (VGO) was generated from vacuum distillation of atmospheric residual oil (AR), and slurry oil (SLO) was generated from catalytic cracking of AR. These heavy oils have similar boiling point ranges in the range of 210-$650^{\circ}C$, but they showed different mass ranges and double-bond equivalent (DBE) distributions. Using DBE and carbon number distributions, aromatic ring distributions, and the extent of alkyl side chains were estimated. In addition to the main aromatic hydrocarbon compounds, those containing sulfur, nitrogen, and oxygen heteroatoms were identified using simple sample preparation and ultra-high mass resolution FT-ICR MS analysis. VGO is primarily composed of mono- and di-aromatic hydrocarbons as well as sulfur-containing hydrocarbons, whereas SLO contained mainly polyaromatic hydrocarbons and sulfur-containing hydrocarbons. Both heavy oils contain polyaromatic nitrogen components. SLO inludes shorter aromatic alkyl side chains than VGO. This study demonstrates that APPI FT-ICR MS is useful for molecular composition characterization of petroleum heavy oils obtained from different refining processes.

• Carbon letters
• /
• v.19
• /
• pp.72-78
• /
• 2016

Spinnable pitches and carbon fibers were successfully prepared from petroleum or coal pyrolysis residues. After pyrolysis fuel oil (PFO), slurry oil, and coal tar were simply filtered to eliminate the solid impurities, the characteristics of the raw materials were evaluated by elemental analysis, ¹³C nuclear magnetic resonance spectrometer, matrix-assisted laser desorption/ionization time-of-flight mass spectrometer (MALDI-TOF-MS), and so on. Spinnable pitches were prepared for melt-spinning carbon fiber through a simple distillation under strong nitrogen flow, and further vacuum distillation to obtain a high softening point. Carbon fibers were produced from the above pitches by single-hole melt spinning and additional heat treatment, for oxidization and carbonization. Even though spinnable pitches and carbon fibers were processed under the same conditions, the melt-spinning and properties of the carbon fiber were different depending on the raw materials. A fine carbon fiber could not be prepared from slurry oil, and the different diameter carbon fibers were produced from the PFO and coal tar pitch. These results seem to be closely correlated with the initial characteristics of the raw materials, under this simple processing condition.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.110.1-110.1
• /
• 2010

A bench scale slurry bubble column reactor (SBCR) with active-Fe based catalyst was developed for the Fischer-Tropsch synthesis (FTS) reaction. Considering the highly exothermic reaction heat generated in the bench scale SBCR, an effective cooling system was devised consisting of a U-type dip tube submerged in the reactor. Also, the physical and chemical properties of the catalyst were controlled so as to achieve high activity for the CO conversion and liquid oil ($C_{5+}$) production. Firstly, the FTS performance of the FeCuK/$SiO_2$ catalyst in the SBCR under reaction conditions of $265^{\circ}C$, 2.5 MPa, and $H_2/CO=1$ was investigated. The CO conversion and liquid oil ($C_{5+}$) productivity in the reaction were 88.6% and 0.226 $g/g_{cat}-h$, respectively, corresponding to a liquid oil ($C_{5+}$) production rate of 0.03 bbl/day. To investigate the FTS reaction behavior in the bench scale SBCR, the effects of the space velocity and superficial velocity of the synthesis gas and reaction temperature were also studied. The liquid oil production rate increased upto 0.057 bbl/day with increasing space velocity from 2.61 to 3.92 $SL/h-g_{Fe}$ and it was confirmed that the SBCR bench system developed in this research precisely simulated the FTS reaction behavior reported in the small scale slurry reactor.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.1
• /
• pp.57-70
• /
• 2017

In this study, we investigated the wear measurement methods for slurry pipe applied in the field of mining and oil sand industry and theoretical equations related to the prediction of wear in slurry pipe through literature review. Average daily wear rate and wear rate per excavated distance were determined from slurry discharge pipe thickness measurement data periodically measured at the actual slurry shield TBM site in Singapore. The wear rate of slurry pipe for Bukit Timah Granite was obtained. The wear rates for G (V) grade and mixed zone were 1.5 times higher than that of G (I) to G (IV) grade. Slurry pipe wear rate tends to increase in proportion to the slurry discharge velocity. The optimal slurry pipe replacement or rotation frequency can be estimated through the selection of the pipe wear rate considering geological condition and the reasonable pipe management thickness.

• Journal of the East Asian Society of Dietary Life
• /
• v.10 no.1
• /
• pp.55-61
• /
• 2000

Physicochemical and sensory characteristics of Yukwa(fried rice cookie) made by different processing condition were investigated to estabilish the optimum expansion of Yukwa. The expansion rate and crispness of Yukwa prepared by soaking waxy rice for 24 hours was satisfactory . Addition of 15% soy slurry gave better effect on increasing the expantion rate, crispiness and sensory preference than no addition of soy slurry . Yeast, Soju(distilled liquor) , Mackeali(rice wine, turbid) and Chunju(rice wine, clear) as expansion reagent were added to Yukwa prepration . Yeast and Mackeali among tested expansion reagent showed better expansion rate and lower hardness meausred by texturometer than Chunju. Yukwa added chungju showed more fine structure and lower expantion rate than others. Microwave puffed Yukwa was less expansion rate, but same level of crispiness and hardness compared with oil puffed. And no difference in sensory characteristics such as degree of crispiness and stickiness of microwave puffed and oil puffed.