• 한국분말재료학회지
• /
• 제21권4호
• /
• pp.266-270
• /
• 2014

Metal foams have a cellular structure consisting of a solid metal containing a large volume fraction of pores. In particular, open, penetrating pores are necessary for industrial applications such as in high temperature filters and as a support for catalysts. In this study, Fe foam with above 90% porosity and 2 millimeter pore size was successfully fabricated by a slurry coating process and the pore properties were characterized. The Fe and $Fe_2O_3$ powder mixing ratios were controlled to produce Fe foams with different pore size and porosity. First, the slurry was prepared by uniform mixing with powders, distilled water and polyvinyl alcohol(PVA). After slurry coating on the polyurethane(PU) foam, the sample was dried at $80^{\circ}C$. The PVA and PU foams were then removed by heating at $700^{\circ}C$ for 3 hours. The debinded samples were subsequently sintered at $1250^{\circ}C$ with a holding time of 3 hours under hydrogen atmosphere. The three dimensional geometries of the obtained Fe foams with an open cell structure were investigated using X-ray micro CT(computed tomography) as well as the pore morphology, size and phase. The coated amount of slurry on the PU foam were increased with $Fe_2O_3$ mixing powder ratio but the shrinkage and porosity of Fe foams were decreased with $Fe_2O_3$ mixing powder ratio.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1992년도 추계학술발표강연 및 논문개요집
• /
• pp.95-96
• /
• 1992

• 한국세라믹학회지
• /
• 제45권12호
• /
• pp.777-781
• /
• 2008

Experiments were conducted using SUS430 and Crofer 22 APU steels coated by LSM using plasma spray and slurry spray methods, respectively. High-temperature conductivity and oxidation resistance were investigated. For comparison, SUS430 and Crofer 22 APU without LSM coating were also investigated and coefficient of thermal expansion (CTE) was measured. The results show that the materials without LSM coating exhibit almost the same CTE as YSZ electrolyte in a range of temperatures of $550{\sim}850^{\circ}C$. When coated with LSM, the oxidation rate of the steels decreases by $30{\sim}40%$ using slurry spray and by $10{\sim}30%$ using plasma spray whereas the steels using plasma spray have a better high-temperature conductivity than the steels using slurry spray. It is thus concluded that the LSM coating has a limited effect on increasing high-temperature conductivity while it can effectively reduce the oxidation of the steels.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.434-437
• /
• 2005

Chemical Mechanical Polishing (CMP) has become an essential step in the overall semiconductor wafer fabrication technology. In general, CMP is a surface planarization method in which a silicon wafer is rotated against a polishing pad in the presence of slurry under pressure. The polishing pad, generally a polyurethane-based material, consists of polymeric foam cell walls, which aid in removal of the reaction products at the wafer interface. It has been found that the material removal rate of any polishing pad decreases due to the so-called 'pad glazing' after several wafer lots have been processed. Therefore, the pad restoration and conditioning has become essential in CMP processes to keep the urethane polishing pad at the proper friction coefficient and to allow effective slurry transport to the wafer surface. Diamond pad conditioner employs a single layer of brazed bonded diamond crystals. Due to the corrosive nature of the polishing slurry required in low pH metal CMP such as copper, it is essential to minimize the possibility of chemical interaction between very low pH slurry (pH <2) and the bond alloy. In this paper, we report an exceptional protective coated conditioner for in-situ pad conditioning in low pH Cu CMP process. The protective Cr-coated conditioner has been tested in slurry with pH levels as low as 1.5 without bond degradation.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.343-348
• /
• 2000

The purpose of this study is to clarify properties adhesive strength of polymer-cement slurry for coated reinforcing bars. The epoxy coating material is superior to performance of anti-corrosion but lately age adhesive strength between concrete raise to structural problems. However, polymer dispersion with excellent performance of elasticity and adhesion can solve this problems. From the test results. adhesion of steel with polymer cement slurry using St/BA emulsion is show excellent without concerned coating thickness, and polymer cement slurry using St/BA emulsion is show adhesion in tension 1.2~2.2MPa at polymer cement ratio 50% of more.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.516-519
• /
• 2011

Indium tin oxide (ITO) coatings were made using an ITO slurry and an ITO sol. This was achieved by dispersing nanosized ITO powder in a mixed solvent without any dispersant and developing an adhesive ITO sol from indium acetate and tin tetrachloride in a mixture of DMF and n-butanol. Coating was carried out in one step by spin coating an ITO slurry, which was then followed by an ITO sol over it. Here, the sol penetrates into the nano ITO particle layers to make them adhere to each other as well as to a glass substrate. This is then followed by sintering at 500$^{\circ}C$ for 1 h to produce a uniform film consisting of ITO particles of about 50 nm and 10 nm. ITO films were obtained with sheet resistances from 450 to 1500 ohm/${\Box}$ by varying spin speed and concentration. Transmittance is higher than 90% at 550 nm.

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 12th KACG Technical Meeting and the 4th Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.19-22
• /
• 1997

The surface modificaion of alumina by $Al_2$O$_3$/SiC nanocomposite coating was studied in terms of processing and microstructure. A powder slurry of 5 vol% SiC composition was dipcoated onto presintered alumina bodies and pressurelessly sintered at 1$700^{\circ}C$ for 2 h in $N_2$. The used of organic binder and plasticizer in the slurry preparation, and the control of the density of presintered alumina body were found to be necessary to avoid cracking and warping during processing. The nanocomposite coating well bonded to the alumina body with thickness about 110 ${\mu}{\textrm}{m}$. The average grain size of coating (2 ${\mu}{\textrm}{m}$) was much finer than that of alumina body (13 ${\mu}{\textrm}{m}$). Fracture surface observations revealed mostly transgranular fracture for the coating, whereas intergranular fracture for the alumina body. Some pores (about 6%) were observed in the coating layer, although the alumina body showed fully dense microstructure.

• 마이크로전자및패키징학회지
• /
• 제13권3호
• /
• pp.33-38
• /
• 2006

유리 조성이 섞인 유전체 파우더와 증류수 그리고 해교제의 혼합으로 만들어진 슬러리를 에어로졸 형태로 고압 스프레이 건으로 기판에 스프레이 코팅 하였다. 기판으로는 알루미나 기판과 전극 패턴이 프린트 된 그린쉬트를 사용하였다. 슬러리 점도와 스프레이 건에 의한 분사모양 그리고 슬러리의 분사량은 코팅 층의 코팅 속도에 영향을 끼쳤으나 밀도에는 거의 영향을 주지 않았다. 고압 스프레이 코팅 방법은 기판에 직접적인 가압 과정이 없으므로 내부 전극은 인쇄된 형태가 유지되었다. 최적 조건에서는 균일하고 조밀한 코팅 층을 얻을 수 있었다. 또한 그린쉬트에 적층 공정을 사용한 기존의 방법과는 달리 고압 스프레이 코팅 방법은 $20{\sim}50{\mu}m$의 얇은 유전체 층을 얻을 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제17권2호
• /
• pp.204-211
• /
• 2006

The electrolyte in the solid oxide fuel cell must be dense enough to avoid gas leakage and thin enough to reduce the ohmic resistance. In order to manufacture the thin and dense electrolyte layer, 8 mol% $Y_2O_3$ stabilized-$ZrO_2$ (8YSZ) electrolyte layers were coated on the porous tubular substrate by the novel vacuum slurry dip-coating process. The effects of the slurry concentration, presintering temperature, and vacuum pressure on the thickness and the gas permeability of the coated electrolyte layers have been examined in the vacuum slurry coating process. The vacuum-coated electrolyte layers showed very low gas permeabilities and had thin thicknesses. The single cell with the vacuum-coated electrolyte layer indicated a good performance of $495\;mW/cm^2$, 0.7 V at $700^{\circ}C$. The experimental results show that the vacuum dip-coating process is an effective method to fabricate dense thin film on the porous tubular substrate.

• 콘크리트학회논문집
• /
• 제27권6호
• /
• pp.633-640
• /
• 2015

본 연구는 EVA와 초조강시멘트로 만든 폴리머 시멘트 슬러리(PCS)로 도장한 도장철근의 부착강도 개선에 영향을 미치는 PCS 도장재 배합에 관한 연구로 도장두께, 폴리머 시멘트비, 도장재의 양생재령을 변화시켜 배합을 설정하여 부착강도 시험을 실시하였다. 본 연구결과, PCS 도장철근의 부착강도는 거의 모든 배합에서 도장하지 않은 보통철근 및 에폭시철근에 비해 높은 부착강도를 나타냈는데 도장철근의 최대 부착강도는 보통철근에 비해 1.32배, 에폭시철근에 비해 1.38배 높게 나타났다. 도장두께는 대체로 얇은 도장두께인 $75{\mu}m$와 $100{\mu}m$에서 부착강도가 높게 나타났으며 폴리머 시멘트비에 따른 영향은 크게 나타나지 않았으나, 내구성면에서 폴리머 시멘트비를 80~100% 범위를 확보하는 것을 제안할 수 있었다. 또한 도장재의 양생재령에 있어서는 7일에서 가장 높은 부착강도를 나타냈으나, 재령 1일에 있어서도 보통철근과 에폭시철근에 비해 높은 부착강도를 보여 현장 시공성 측면에서 1일 재령을 제안 할 수 있었다.