• Journal of Industrial Technology
• /
• v.25 no.B
• /
• pp.55-62
• /
• 2005

This paper is the results of experimental and numerical works on analyzing the geotechnical engineering behavior and characteristics of excavated clay slope formed by the method of excavated replacement which is one of treatments in soft soil ground. For the centrifuge model tests, models of excavated clay slope were prepared by remolding the marine clayey soil sampled from the field. Tests were performed with changing the slope to investigate the behavior of them. On the other hand, numerical analyses were carried out to analyze the change of safety factor against instability of slope with time. Changes of pore water pressure, shear strength and displacement were also investigated. As results of centrifuge model tests with slopes of 1:1.5 and 1:3 using the confining body of simulating the effect of excavation, for the case of 1:1.5, slope failure occurred right after remove the confining body whereas relatively small displacements within the range of 3.2mm, implying to maintain the stability of slope, were observed for the case of 1:3 slope. From the results of numerical analyses using the software of PLAXIS to investigate the stability of slope after excavation, the minimum safety factor against slope failure was 1.28 for the case of 1:3 slope. The further researches in the future are required with considerations of build up of static pore water pressures during acceleration of centrifuge, depth of excavation influencing the behavior of the slope and permeability of the slope since excavation of the slope was not simulated well resulted from the limitations of apparatus at the stage of excavation during the centrifuge tests.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1302-1308
• /
• 2010

This study the change of the safety factor before and after the reinforcement were compared by performing the parameter research based on the limit equilibrium analysis regarding the same cross section after carrying out the safety factor before the reinforcement on the virtual section in order to observe the change of the safety factor of the slop reinforced with the slope planting reinforced earth, and the variation of the safety factor according to the increase of the length of the reinforcement materials and the change of the slope height was analyzed. As the result, the reinforcement effect was insignificant at no more than 0.6 of L/H, the reinforcement length ratio when the reinforcement length was increased, as the increase of the safety factor was slow comparing with the non-reinforced slope. At 3.0m of the slope height, reinforcement on the slope is not necessary, and at 3.0m to 5.0m of the slope height, the inclination was not influencing at no less than 0.6 of L/H. At 5.0m to 9.0m of the slope height, the safety factor was mostly secured on the slope at 0.8 of L/H and the over-reinforced slope appeared at no less than 1.0 of L/H. Also, the safety factor increased as the slope height increases and the slope gets steeper till 0.8 of L/H, but the slope steepness affects more on the increase of the safety factor than the reinforcement material, as the reinforcing force by the reinforcement material became steady.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.644-651
• /
• 2006

In general, a damage that occurs due to landslide or slope failure in urban areas is larger than that in rural areas. In order to reduce the damage, a program is necessary to categorize slopes based on properties and to manage them systematically. Based on the above necessity, a slope management program which is applicable to slope management in an urban area has been developed at Hwangryung mountain in Busan as a target area. The program has a function of systematic slope information constructed by slope ID number of each slope or sub-region of a mountain, making a slope data sheet, analysis and grouping of slope stability, and establishment of a data base. It can also be utilized practically by end users due to the convenient input, edition, printing, management and operation of slope data. For practical utilization of the developed program, a research related to construction of the slope management system for a regional area is demanded to be performed continuously. The supply and utilization of a web based slope management system would contribute to damage reduction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.411-418
• /
• 2009

So far the Limit Equilibrium Method has been widely used by way of 2-D slope stability analysis for the evaluation of land slides and slope failures. However recently the evaluation of 3-D slope stability analysis has been comparatively possible owing to the developments of obtaining the terrain data and geological data and of 3-D slope stability analysis softwares. In Japan the evaluation of the 3-D slope stability analysis has been necessary for the stability analysis of the tunnel mouth. In this study we inspected the economic effects introducing the 3-D slope stability analysis for larger scale landslides and slope failures. In case of 3-D slope stability analysis of landslides we acquired the results that we reduce the cost of the countermeasure work of pile work by 40% comparing the 2-D slope stability analysis. Moreover in case of the stability analysis of slope failures we figured out the results that we reduce the cost of the countermeasure work of anchor works by 20%. Furthermore we proved that 3-D slope stability analysis is effective for the stability analysis of tunnel mouths around the sides of landslides and large scale embankment which we could have not evaluated by conventional 2-D section stability analysis.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.1
• /
• pp.67-77
• /
• 2018

The objective of this study is to extract the shape of the slope from the images acquired using UAV and evaluate its suitability and reliability when applied to slope stability analysis. UAV is relatively inexpensive and simple, and it is possible to make terrain survey by generating point clouds. However, the image acquired from UAV can not be directly photographed by the forest canopy due to the influence of trees, resulting in severe distortion of the terrain. In this study, therefore, the effects of forest canopy were verified and the slope stability analysis was performed. Images acquired in winter and summer were used, because summer images are heavily influenced by the forest canopy and winter images are not. As a result of the study, the winter image is suitable for the extraction of slope shape, but severe terrain distortion occurs in the summer image. Therefore, slope stability analysis using slope shape extracted from summer image is impossible, so it should be modified for slope stability analysis. The modified slope did not completely eliminate the distortion of the terrain, but it could express the approximate shape of the slope. As a result of the slope stability analysis, the location and shape of the failure surface are the same, and the error of the safety factor is less than 0.2, which is close to the actual slope.

• Geomechanics and Engineering
• /
• v.31 no.5
• /
• pp.439-452
• /
• 2022

A forecast of slope behavior during catastrophic events, such as earthquakes is crucial to recognize the risk of slope failure. This paper endeavors to eliminate the significant supposition of predefined slip surfaces in the slope stability analysis, which questions the relevance of simple conventional methods under seismic conditions. To overcome such limitations, a methodology dependent on the slip line hypothesis, which permits an automatic generation of slip surfaces, is embraced to trace the extreme slope face under static and seismic conditions. The effect of earthquakes is considered using the pseudo-static approach. The current outcomes developed from a parametric study endorse a non-linear slope surface as the extreme profile, which is in accordance with the geomorphological aspect of slopes. The proposed methodology is compared with the finite element limit analysis to ensure credibility. Through the design charts obtained from the current investigation, the stability of slopes can be assessed under seismic conditions. It can be observed that the extreme slope profile demands a flat configuration to endure the condition of the limiting equilibrium at a higher level of seismicity. However, a concurrent enhancement in the shear strength of the slope medium suppresses this tendency by offering greater resistance to the seismic inertial forces induced in the medium. Unlike the traditional linear slopes, the extreme slope profiles mostly exhibit a steeper layout over a significant part of the slope height, thus ensuring a more optimized solution to the slope stability problem. Further, the susceptibility of the Longnan slope failure in the Huining-Wudu seismic belt is predicted using the current plasticity approach, which is found to be in close agreement with a case study reported in the literature. Finally, the concept of equivalent single or multi-tiered planar slopes is explored through an example problem, which exhibits the appropriateness of the proposed non-linear slope geometry under actual field conditions.

• The Journal of Engineering Geology
• /
• v.18 no.1
• /
• pp.17-26
• /
• 2008

In this study, the design method of slope reinforced by the earth retention systems were systematically developed, and the flow chart of design procedure fur each system were constructed to design the slope rationally. The proposed design method is composed of 5 steps such as field condition investigation step, slope design step, landslide occurrence prediction step, slope failure scale estimation step and reinforcement countermeasure selection step. The quantitative standard of slope failure scale was established based on the arrangement of various overseas standards which is estimating the slope failure, and the analysis of slope failure scale which is occurred in the country. The slope failure scale is classified into three categories the small scale of slope failure is less than $150m^3$ of slope failure volume, the middle scale of slope failure is from $150m^3$ to $900m^3$ and the large scale of slope failure is more than $900m^3$. The earth retention system could be selected by the proposed slope failure scale based on the slope failure volume. Meanwhile, the design methods of earth retention system such as piles, soil nails and anchors were developed. The optimal countermeasure for slope stability could be proposed using above design methods.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.289-297
• /
• 2007

Slope failure that is occurred by rainfall generates a lot of property damages and loss of lives. Slope stability management and reinforcement countermeasure can be attained through continuous monitoring about various slope types that adjoin in human's life for reducing slope failure from natural and artificial cut slope hazards. The study area is rock slope that is consisted of gneiss, and large scale joint set is ranging by fault activity. This rock mass is exposed during long period and has lithological weathering property of weathered rock or soft rock. In-situ investigation carried out after divide by natural slope and cut slope. As a result, the natural slope appeared to high possibility of planar failure and wedge failure in few joint points that main joint set is formed. On the other hand, slope failure conformation in cut slope was superior only wedge failure occurrence possibility in eight joint points. In result of numerical analysis using SLIDE 2D, the minimum safety factor was analyzed slope stability for cut slope relatively low than natural slope in this study.

• The Journal of Engineering Geology
• /
• v.24 no.3
• /
• pp.383-396
• /
• 2014

The condition, characteristics, and stability of slopes, as well as the consequences of slope failure, need to be understood for the proper stabilization of slopes and preclusion of potential disasters arising from slope failure. Here, a slope code system (SCS) that succinctly and accurately reflects the various conditions of a slope is proposed. The SCS represents the condition, characteristics, and geotechnical stability of slopes, as well as the consequences of slope failure, and the method is quickly and easily applied to a given slope. The SCS comprises five elements: 1) the slope material; 2) the genetic origin (rock type) and geological structure of the slope; 3) the geotechnical stability of the slope; 4) the probability of failure and remedial works made upon the slope; and 5) the consequences of failure. A letter code is selected from each element, and the result of the evaluation and classification of the slope is given as a five-letter code. Because the condition, characteristics, and geotechnical stability of a slope, as well as the consequences of slope failure, are provided by the SCS, this system will provide an effective mechanism for the maintenance and management of slopes, and will also allow more informed decision-making for determining which slopes should be prioritized for remedial measures.

• Journal of The Korean Society of Integrative Medicine
• /
• v.5 no.4
• /
• pp.1-9
• /
• 2017

Purpose : This study was conducted among 195 adults in their 20s. To analyze the impact of the slope types of the scapulae on the plantar surface of the foot, the average pressure (AP), the maximum pressure (MP), the average of local distribution values, and the average movement of the center of pressure (COP) of the different slope types of the scapulae were compared. Method : The anterior-posterior slopes of the scapulae were measured by comparing the slopes of the left and right sides of the scapulae based on the differences in the height and the slope of the coracoid process and the angulus inferior scapulae. Those whose left side of the scapulae had an anterior slope were categorized as type 1, and those whose right side of the scapulae had an anterior slope, as type 2. The average plantar pressure, the center of plantar pressure, the maximum plantar pressure, and local distribution values were analyzed using a plantar pressure analyzer of the FSA. Result : In terms of the AP of the left and right feet, there was no statistically significant difference both in types 1 and 2 on the left and right feet. The comparison results of the MP and the average of local distribution values of the two slope types of the scapulae showed that there was no statistically significant difference on the X-axis both in types 1 and 2 on the left and right feet, but that there was a large statistically significant difference on the Y-axis both in types 1 and 2. That is, the MP of the right foot of the left anterior slope type was located more on the hindfoot than that of the right anterior slope type, and the MP of the left foot of the left anterior slope type was located more on the hindfoot than that of right anterior slope type. Conclusion : This study can be used as fundamental data to predict differences in the location and size of the COP and changes in plantar pressure distribution depending on the slope types of the scapulae, and control the distribution for therapeutic purposes.