• Composites Research
• /
• 제12권1호
• /
• pp.11-18
• /
• 1999

섬유로 강화된 열가소성 복합재의 성형과정 중에는 유동특성에 미치는 금형내 충전패턴의 제어나 섬유배향 및 섬유함유율과 같은 성형공정 인자들의 영향을 예측하는 것이 필요하다. 본 연구에서는 등온상태에서 두께가 얇거나 두꺼운 성형품을 압축성형하는 경우에 발생하는 유동선단과 압력분포, 속도구배 등을 예측함을 목적으로 한다. 이때 복합재는 비압축성 뉴턴유체로 하였으며, 성형공정 변수들에 미치는 미끄럼 지배상수 $\alpha$와 점성비 $\zeta$의 영향에 대해서 고찰한 내용을 보고한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.335-338
• /
• 2007

공대공미사일의 경우 초음속 하에서 고 기동성을 얻기 위하여 고받음각 능력이 요구되어진다. 옆 미끄러짐이 없는 대칭형 세장형 몸체의 경우라도 비대칭 와류는 생성된다. 이러한 비대칭 와류는 불필요한 측력 및 요잉모멘트를 발생시키고 이는 곧 방향 안전성을 저하시킨다. 본 연구는 전산해석을 통하여 초음속유동하에서 세장형 몸체 주변에 발생되는 비대칭와류 모사를 실시하였으며 비대칭 와류의 모사를 위해 선두부에 Bump를 장착하였다. 전산해석 결과 세장형 몸체 주변에 발생하는 비대칭와류를 모사 할 수 있었다.

• Korea-Australia Rheology Journal
• /
• 제15권2호
• /
• pp.97-105
• /
• 2003

In the previous paper (Hyun et al.,2002), we have investigated the shape of storage modulus (G') and loss modulus (G") of complex fluids under large amplitude oscillatory shear (LAOS) flow. As the strain amplitude increases, owever, the stress curve becomes distorted and some important information may be smothered during data processing. Thus we need to investigate the stress data more precisely and systematically. In this work, we have obtained the stress data using high performance ADC (analog digital converting) card, and investigated the nonlinear response of complex fluids, 4wt% xanthan gum (XG), 2 wt% PVA/ 1 wt% Borax, and 1 wt% hyaluronic acid (HA) solutions, using Fourier transformation (FT) rheology. Comparing the strain signals in time domain with FT parameters in frequency domain, we could illustrate the sensitivity and importance of FT rheology. Diverse and unique stress patterns were observed depending on the material system as well as flow environment. It was found that they are not the outcome of experimental deficiency like wall slip but characteristics of the material system. When nonlinear response of complex fluids is analyzed, the intensity and phase angle of higher harmonic contributions should be considered together, and the shape of the stress signal was found to be strongly dependent upon phase angle.ngle.

• 소성∙가공
• /
• 제20권3호
• /
• pp.229-235
• /
• 2011

The formability of magnesium alloy sheets at room temperature is generally low because of the inherently limited number of slip systems, but higher at temperatures over $150^{\circ}C$. Therefore, prior to the practical application of these materials, the forming limits should be evaluated as a function of the temperature and strain rate. This can be achieved experimentally by performing a series of tests or analytically by deriving the corresponding modeling approaches. However, before the formability analysis can be conducted, a model of flow stress, which includes the effects of strain, strain rate and temperature, should be carefully identified. In this paper, such procedure is carried out for Mg alloy AZ31 and the concept of flow stress surface is proposed. Experimental flow stresses at four temperature levels ($150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$, $300^{\circ}C$) each with the pre-assigned strain rate levels of $0.01s^{-1}$, $0.1s^{-1}$ and $1.0s^{-1}$ are collected in order to establish the relationships between these variables. The temperature-compensated strain rate parameter which combines, in a single variable, the effects of temperature and strain rate, is introduced to capture these relationships in a compact manner. This study shows that the proposed concept of flow stress surface is practically relevant for the evaluation of temperature and strain dependent formability.

• 한국전산유체공학회지
• /
• 제18권2호
• /
• pp.85-92
• /
• 2013

In this study, we consider heat transfer enhancement in laminar channel flow by means of an infinite streamwise array of equispaced identical circular cylinders. This flow configuration can be regarded as a model representing a micro channel or an internal heat exchanger with cylindrical vortex generators. A numerical parametric study has been carried out by varying Reynolds number based on the bulk mean velocity and the cylinder diameter, and the gap between the cylinders and the channel wall. An immersed boundary method was employed to facilitate to implement the cylinders on a Cartesian grid system. No-slip condition is employed at all solid boundaries including the cylinders, and the flow is assumed to be periodic in the streamwise direction. Also, the Prandtl number is fixed as 0.7. For thermal boundary conditions on the solid surfaces, it is assumed that heat flux is constant on the channel walls, while the cylinder surfaces remain adiabatic. The presence of the circular cylinders arranged periodically in the streamwise direction causes a significant topological change of the flow, leading to heat transfer enhancement on the channel walls. The Nusselt number averaged on the channel wall is presented for the wide ranges of Reynolds number and the gap. A significant heat transfer enhancement is noticed when the gap is larger than 0.8, while the opposite is the case for smaller gaps. More quantitative results as well as qualitative physical explanations are presented to justify the effectiveness of varying the gap to enhance heat transfer from the channel walls.

• 대한기계학회논문집B
• /
• 제31권11호
• /
• pp.895-903
• /
• 2007

CMBT(Curved Moving Boundary Treatment) is a newly developed scheme for the treatment of a no slip condition on the curved solid wall of moving obstacle in a flow field. In our research CMBT was used to perform LBM simulation of a flow over a moving circular cylinder to determine the flow feature and aerodynamics characteristic of the cylinder. To ascertain the applicability of CMBT on the complex shape of the obstacle, it was first simulated for the case of the flow over a fixed circular cylinder in a channel and the results were compared against the solution of Navier-Stokes equation with deforming mesh technique. The simulations were performed in a moderate range of reynolds number at each moving cylinder to identify the flow feature and aerodynamic characteristics of circular cylinder in a channel. The drag coefficients of the cylinder were calculated from the simulation results. We have numerically confirmed that the critical reynolds number for vortex shedding is ar Re=250 and the result is the same as the case of fixed cylinder. As the cylinder approaching to one wall, the 2nd vortex is developed by interacting with the wall boundary-layer vorticity. As the velocity ratio increase the third vortex are generated by interacting with the 2nd vortexes developed on the upper and lower wall boundary layer. The resultant $C_d$ decrease as reynolds number increasing and the Cd approached to a value when Re>1000.

• 간호행정학회지
• /
• 제1권1호
• /
• pp.147-211
• /
• 1995

Medication is a kind of medical service and a therapeutic nursing function which takes large portion of nursing service and requires complicated procedures. So many different medical personnel should be involved and cooporate each other in order to accomplish medication. Medication is also a vital nursing service, So nurse feels heavy responsibi lity in that she gives medication to the patient finally, so she has much responsibility if medication error is happened. Therefore it seems very important to clarify the problem of medication system and method, and find the subculture of medication situation because it may promote nursing productivity. The study was conducted to 1. Describe and interpret medication situation. 2. Find out the problem of medication system and method and on alternatives. 3. Compare the medication system and method of hospitals which are located in Seoul with object hospital Ethnographic methodology was used to study medication situation by doing participant observation and interview of health care personnel. Ten nurses and three nurse aids were interviewed. Two residents and internists, two phamacists and two accountants were also interviewed. Data was obtained and analized according to Developmental Research Sequence introduced by Spradly. On the basis of this data the results were as follows. 1. The overall flow of medication system was devided into six stage : first, checking doctor's order : second writing doctor's order, : third, transfering slip into the related departments such as account department, pharmacy : fourth, distribution of medication from pharmacy to unit : fifth, identifing medication by nurses : and finally, medicating to the patient. Behaviorors have been under a lot of stress in that they have to do much works, especially paperworks, So too much time were needed. They also have been suffered interpersonal conflicts among health care personnel and role conflicts in the process of doing medication service. 2. In the process of checking order, the problem was that too much time was required for checking order and paperwork. The more the order changes the more the paperwork is. Nurses have been suffering difficulties in calling internist in order to get bill. Even if writing down slip for medication order is doctor's job, Sometimes nurse has been expected to write slip by doctors or nurse would write slip beacuse of two much complexities and efforts for calling doctors. If the slip were incorrect, much time complicated procedures were more required for correcting it. So delay of administering drug would be resulted consequently. Drugs were delivered from pharmacy to units by delivery agent and phamacist. But because drugs were delivered without arranging room number of patient. Nurse should rearrange drugs in order of the room number So it had made waste time and effort, and Even when emergency drugs were needed, Prompt delivery of drug was not easy because of many reasons. For nurses, it took too long in the identification of the right drug. Actually nurses have heavy burden when medication error happens because nurse is the final actor who gives medication to the patient, So every three shift nurse ought to check drugs as soon as every shift begins. That's why it took too much time due to repeated confirming procedure. When nurses had to go patient room in order to give medications, there were difficulties in watching patient until the patient take medicine correctly. So it was impossible to check every patient wheather he took medicine or not especially in hectic situation. 3. There were many hospitals in Seoul which have similar medication system and method as object hospital according to the results of questionaire. This means that many hospitals have been suffering srimilar problems which were identified in object hospital. 4. Recommendations for promoting simplification of medication system and method were the following : Redesigning of slip from two pieces of paper into one : early discharge announcement system, and slip confirming through computer and controlling of period of prescreption from one day to two or three days : designing personal drug storage box for each patient and using it. If nurses follow the recommendations, they will make medication short & simple, and also have enough time of direct nursing care 5. Even though there were many difficulties in medicating patients. Medication itself has been considered as a caring among nurses because it makes rapport between nurse and patient. So nurses had better accept medication as a portion of nusing service not a original portion of phamacist. There are some limits in this research in terms of confining to only one unit of one hospital, and treating it especially in view of nurses' aspects, So further researchs should be continnued from various kmds of viewpoints of doctors, phamacists and so on. ${\cdot\cdot\cdot}$. Especially esthnographic study of computerized medication system and method seems to be followed.

• 터널과지하공간
• /
• 제30권4호
• /
• pp.320-334
• /
• 2020

본 수치해석연구에서는 국제공동연구프로젝트 DECOVALEX2019의 Task B의 일환으로 PFC3D를 기반으로한 수리역학연계모델을 개발하여 스위스 Mont Terri 지하연구시설에서 수행된 단층의 유체주입으로 인한 슬립시험을 모사하였다. 이를통해, 개발한 PFC3D 수리역학연계모델이 가진 한계점과 향후 보완할 점을 검토하고자 하였다. PFC3D를 기반으로한 3차원 입자결합모델 내 공극-유동통로모델을 생성하였으며 이를 사용하여 Mont Terri Step 2 단층내 유체주입실험을 모사하였다. 모델링결과 단층대를 따라 주입유체의 유동에 의한 단층대의 변형을 확인하였지만, 관측정에서의 시간에 따른 수압변화는 현장측정치와 부분적으로 일치하는 경향을 확인하였다. 현장측정 관측수압은 초기 유체주입 압력증가에 거의 변화를 보이지 않고 주입수압이 최대치에 도달할때쯤 급격한 증가를 보이는반면, 모델링에서는 주입압력이 증가함에 따라 관측수압도 부드럽게 증가하는 경향을 보였다. 이러한 부분적으로 일치하는 결과의 원인으로는 Mont Terri 현장의 단층을 모사하는 방법에 기인하는 것으로 판단하다. PFC3D에서는 단층을 손상대와 코어균열의 조합으로 모사하였고 단층대의 두께가 약 2 m로 주입유체가 단층대를 통해 유동하도록 모사하였기에 현장에서의 주입유체의 단층내 유동보다 그 유동범위가 크게 모사되었다고 판단한다. 또한, 현장단층에서와 같이 단층내부에 존재하는 충진물질로 인해 단층내 수리유동이 제한되어 국부적으로 과잉공급수압이 형성될 수 있는 기재를 모사하지 못한 점 또한 모델링 결과와 현장측정결과가 부분적으로 일치하는 원인일 수 있다. 단층변형의 경우는 모델링결과와 현장측정결과 유사한 수준으로 일치하는 결과를 확인하였다. 수치모델을 변형하여 단층대의 두께를 감소시키고 단층내 충진 물질의 비균질적인분포를 모사할 수 있는 방법론에 대한 후속 연구를 통해 PFC3D 수리역학연계모델의 유체주입으로 인한 단층활성화 연구로의 적용성을 향상시키는 것을 제안하고 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권3호
• /
• pp.360-368
• /
• 2010

A SCR catalytic filter system is used for reducing $NO_x$ and soot emissions simultaneously from diesel combustors. The amount of ammonia (as a reducing agent) must be controlled with the amount of $NO_x$ to obtain an optimal $NO_x$ conversion. Hence, gas mixing between ammonia and exhaust gases is vital to ensure that the SCR catalyst is optimally used. If ammonia mass distribution is not uniform, slip potential will occur in rich concentration areas. At lean areas, on the other hand, the catalyst is not fully active. The better mixing is indicated by the higher uniformity of ammonia mass distribution which is necessary to be considered in SCR catalytic filter system. The ammonia mass distributions are depended on the flow field of fluids. In this study, the velocity field of gaseous flow is investigated to characterize the transport of ammonia in SCR catalytic filter system. The influence of different injection placements on the ammonia mass distribution is also discussed. The results show that the ammonia mass distribution is more uniform for the injector directed radially perpendicular to the main flow of inlet at the gravitational direction than that at the side wall for both laminar (Re = 640) and turbulent flows (Re = 4255). It is also found that the mixing index decreases as increasing the heating temperature in the case of ammonia injected at the side wall.

• Journal of Mechanical Science and Technology
• /
• 제14권1호
• /
• pp.84-92
• /
• 2000

A new bounce back boundary method of the second order in error is proposed for the lattice Boltzmann fluid simulation. This new method can be used for the arbitrarily irregular lattice geometry of a non-slip boundary. The traditional bounce back boundary condition for the lattice Boltzmann simulation is of the first order in error. Since the lattice Boltzmann method is the second order scheme by itself, a boundary technique of the second order has been desired to replace the first order bounce back method. This study shows that, contrary to the common belief that the bounce back boundary condition is unilaterally of the first order, the second order bounce back boundary condition can be realized. This study also shows that there exists a generalized bounce back technique that can be characterized by a single interpolation parameter. The second order bounce back method can be obtained by proper selection of this parameter in accordance with the detailed lattice geometry of the boundary. For an illustrative purpose, the transient Couette and the plane Poiseuille flows are solved by the lattice Boltzmann simulation with various boundary conditions. The results show that the generalized bounce back method yields the second order behavior in the error of the solution, provided that the interpolation parameter is properly selected. Coupled with its intuitive nature and the ease of implementation, the bounce back method can be as good as any second order boundary method.