• Journal of Mechanical Science and Technology
• /
• 제17권12호
• /
• pp.1904-1911
• /
• 2003

In order to determine the wear properties of AIP (Arc Ion Plating) deposition, wear process was evaluated by using a Falex test machine. Also, in order to determine the effects of coating material on the wear process, TiC, TiN, and TiCN coatings of thickness about 5 $\mu\textrm{m}$∼6 $\mu\textrm{m}$ coated by Arc ion plating deposition method were tested. The wear property was determined under a dry sliding condition as a function of the applied load, sliding distance, sliding velocity and temperature. The results show that when wear of the coating-layer occurred, specific wear amount increased with the wear rate. At initial state, the wear rate rapidly increased, but it gradually reduced as the velocity increased. Also, when raising the temperature, the wear rate increased in the order of TiCN, TiN and TiC due to the frictional heat.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.292-299
• /
• 1998

The effect of characteristic of surface roughness on friction and sliding wear was studied experimentally with ball-on-disk type wear tester. The test was conducted with specimens those have varying arithmetic mean value, skewness and kurtosis under the condition of different load, sliding speed and lubricant viscosity. The surface of the lower skewness in negative value or the highel kurtosis tends to have low friction for the same arithmetic mean value. There is optimum arithmetic mean value surface roughness for operating variables have load, speed, etc.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.49-53
• /
• 2002

Inconel 690 for nuclear steam generator tube has more chromium than the conventionally used Inconel 600 in order to increase the corrosion resistance. TD evaluate the tribological characteristics under fretting condition the fretting tests as well as sliding tests were carried out in elevated temperature water environment. Fretting tests of the cross-cylinder type were done under various vibrating amplitudes and applied normal loads in order to measure the friction forces and wear volumes. Also, the conventional sliding tests of pin-en-disk type were carried out to compare the test results. In fretting, the friction was very sensitive to the load and the amplitude. The friction coefficient decreased with increasing load and decreasing amplitude. Also, the wear of Inconel 690 can be predictable using the work rate model. Depending on normal loads and vibrating amplitudes, distinctively different wear mechanisms and of ten drastically different wear rates can occur. It was fecund that the fretting wear coefficients in water were increased as increasing the temperature of water.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.26-30
• /
• 1995

Sliding experiments have been conducted on alumina and silicon carbide ceramics. Wear and friction data of both materials indicate that wear proceeds in two distinct stages. The wear occurs by a relatively mild plastic-grooving process in the initial stage, but eventually gives way to a severe grain pull-out process after a defined period of sliding test. The datails of the transition mechanism are presented. The effects of grain size and second phase particle on the wear transition are also presented.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.635-642
• /
• 2010

The paper presents a multimedia educational program of DC servo drives for distant learning with a special emphasis on sliding mode control. The program contains of three parts: animation, simulation and internet based measurement. The animation program explains the operation of DC motors, gives its time- and frequency-domain equations, transfer functions and the theoretical background necessary for controller design for DC servo motors. The simulation model of the DC servo motor and the controller can be designed by the students based on the animation program. The students can also test their controllers through the internet based measurement, which is the most important part from engineering point of view. After the measurements are executed, the students can download the measured data and compare them to the simulation results.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.378-384
• /
• 2000

This paper presents the results of the repeated sliding tests to determine the wear-life of TiN coated AISI 52100 bearing balls deposited by PVD method and to show the wear mechanisms of those. The sliding tests were carried out using a ball-on-disk tribometer under ambient conditions. The coefficient of friction, wear volume and the cycles to failures of TiN coated bearing balls were measured with different normal loads and roughness of lower specimens. On the wear-life diagram, the normal loads and the cycles to failure showed the good linear relation on log-log coordinate. With a decreasing normal load, the diagram showed that the wear-limits, at which the coated bearing balls survived more than 4000cycles were under 0.1N of the normal load.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.66-72
• /
• 2009

Al-based composites reinforced with SiC particulate were fabricated using a thermal spray process, and dry sliding wear behavior of the composites was investigated. Pre-mixed Al and SiC powders were sprayed on an A16061 substrate by flame spraying, and dry sliding wear test were performed under various sliding speed and applied load conditions against ${Al_2}{O_3}$ ball. Wear behavior of the composites was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). And build-up mechanism of MML on the worn surface of the composites was examined. It was revealed that these MML was formed of debris from the contact surface of the composites and effected to wear behavior of the composites protecting the contact surface of the composites.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.155-156
• /
• 2002

During the sliding between a-CNx and $Si_3N_4$, applying nitrogen as environmental gas provided very low friction as the level of 0.01 in friction coefficient. In order to know the effect of the running-in process on the reduction of the friction, the effect of surface roughness of mating surface on friction was investigated. It was shown that smooth surface in wear scar of ball provided low friction coefficient. Friction coefficient after running-in was proportional to the Ry value of wear scar of ball. Also smooth thin transferred layer was observed on the wear scar of balls with an AFM after sliding test. Those results showed the smoothing of wear scar of ball, the generating of the transferred layer from CNx was necessary for low friction.

• 한국산학기술학회논문지
• /
• 제11권1호
• /
• pp.21-28
• /
• 2010

본 논문에서는 만타형상 무인잠수정(Manta-type unmanned underwater test vehicle)의 운동성능과 제어기설계에 대한 성능을 해석하기 위한 수학모델을 정립하여 시뮬레이션 프로그램을 개발하였다. 6자유도 운동방정식을 이용하여 Matlab/Simulink로 시뮬레이션 프로그램을 구성하였다. 개발된 시뮬레이션 프로그램을 이용하여 만타형상 무인잠수정의 동역학적 운동성능을 해석하였으며, 무인잠수정의 제어성능을 해석하기 위하여 PID(비례-미분-적분)제어기와 슬라이딩모드(Sliding mode)제어기를 설계하여 만타형상 무인잠수정의 제어성능을 해석하였다. 설계된 제어기는 무인잠수정의 수심제어(Depth control)와 방향제어(Heading control)에 사용되었다. 설계된 제어기의 성능을 확인하기 위하여 미해군 대학원의 AUV II와 비교하였다. 설계된 수심제어기와 방향제어기를 이용하여 만타형 무인잠수정의 설계목표에 부합하는 항해제어 시뮬레이션을 실시하였다.

• 대한토목학회논문집
• /
• 제40권5호
• /
• pp.445-454
• /
• 2020

차량과 충돌 시 분리되지 않는 감충형 슬라이딩 지주는 충돌 초기에 차량과 일체로 되어 강체운동을 한다. 이때 차량의 선형모멘텀이 지주에 전달되면서 차량의 1차 감속을 이루고 이어서 가이드레일 아래에 설치된 Energy-Absorbing Pipe (EAP)가 찌그러지면서 나머지 충돌에너지를 흡수하여 2차 감속을 이룬다. 따라서 EAP는 슬라이딩 지주의 핵심요소이고 그 크기는 지주기초 안에 설치될 수 있어야 한다. 본 논문은 국내 편 지식 표지판에 많이 사용되는 지주와 베이스구조를 합하여 총 507 kg의 무게를 갖는 감충형 슬라이딩 지주에 사용하기 위한 EAP의 개발에 관한 것이다. LS-DYNA프로그램을 이용한 충돌해석을 통하여 EAP구조를 설계하고 실차충돌실험을 통하여 감충성능을 평가하는 과정을 상세히 설명하였다. 본 연구를 통하여 제시된 EAP는 최소 0.9 ton-60 km/h에서 최대 1.3 ton-80 km/h 충돌에 대한 감충성능을 발휘하고 기초길이가 2.7 m 이하로 제약될 때 활용될 수 있다.