• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2875-2878
• /
• 2011

The wooden sleeper has been used at the railway track. Recently the concrete sleeper is pushing the wooden sleeper out, but huge amount of waste wooden sleepers are discharged every year. Due to the contaminant of waste wooden sleeper, its disposal is very difficult. Commonly a wood preservative such as creosote is used in the manufacturing process and it becomes major contaminant after use. And the wooden sleeper is contaminated by diesel from locomotives and lubricant oil from the maintenance of railway turnout. Currently the limitary disposal methods can be used because of high toxicity of waste wooden sleeper. Therefore the preliminary study on thermal-extraction of contaminants such as creosote, diesel and lubricant oil from waste wooden sleeper was conducted and the effects of factors were investigated.

• International Journal of Railway
• /
• v.9 no.2
• /
• pp.46-49
• /
• 2016

In this study a new detection technique based on WAK is introduced that can be used for identifying unstable concrete sleeper installed in ballast by triggering activated wave on the sleeper surface. If a gap exists immediately below the concrete sleeper, static stiffness can be lower than stable case's stiffness. The concrete sleeper is assumed as a single degree of freedom system (SDOF). The static stiffness K can be obtained by iteratively calculated mass (m), stiffness (k) and damping coefficient (c) of SDOF system. Those coefficients are used to specify the ballast condition such as a gap between the sleeper and ballast. Typical test results using a small sleeper model test are summarized and explained for proof of effectiveness of the WAK test for checking unstable condition of the sleeper.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.2 no.1
• /
• pp.121-128
• /
• 1998

The rail, which supports the train road, distributes the wheel loads to the tie by rail stiffness. Subway sleeper on concrete ballast is construction of PC or RC sleeper. The present, PC sleeper is constructed of line 1, 2, 3, 4 Seoul Subway and RC sleeper is planing construction for the STEDEF system on concrete ballast of the line 5, Seoul, Taegu, and Kwangju Subway. The major purpose of this study is to check influence of the angle with analysising the behavior of sleeper according to the existent or non-existent of angle. And the study is carried to check static analysis by manufacture of same model.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.633-641
• /
• 2002

Wooden-sleeper, which has been adopted as railway turnout in Korea, has created many problems such as short life span and increase of maintenance cost. Especially turnout on Maintenance Free slab track, which has been used in city metro, has been constructed with wooden sleeper buried in concrete roadbed due to complexity of structure. However, such problem as rapid erosion in subground makes it difficult to maintain the sleeper because of frequent replacement required. Therefore, the objective of this paper is to introduce design and construction of reinforced concrete(R.C) sleeper for turnout on the concrete roadbed to facilitate maintainability and economic construction of turnout.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1248-1253
• /
• 2011

It is increasing construction of long span railway bridge with concrete track system for speed up of railway and efficient maintenance of track. As the sleeper of the concrete track system layed on a bridge is fixed on deck of the bridge, the displacement of the sleeper and deck is same. Therefore, the spacing between two sleeper installed at the end of the adjacent deck near the expansion joint of bridge becomes vary according to the longitudinal expansion of a deck by temperature change. By the way, if the spacing of sleepers become increase excessively, it causes large bending stress of in a rail, and it can leads failure or reduction of fatigue life of the rail. Further more, the excessive displacement of the rail may induce decrease ride comfort as well as corrugation of rail surface. Therefore, it is required to determine the allowable maximum sleeper spacing to prevent such problems. For the purpose, investigation on the influence factor on sleeper spacing for straight track was carried out. Variation of bending moment in a rail, wheel force, and the ratio of primary and secondary deflection of the rail according to sleeper spacing was investigated, and, as a result, the maximum allowable sleeper spacing at the bridge expansion joint was suggested.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.5
• /
• pp.515-524
• /
• 2022

The turnout system of the sleeper floating tracks (STEDEF) on urban transit is a Anti-vibration track composed of a wooden sleeper embedded in a concrete bed and a sleeper resilience pad under the sleeper. Therefore, deterioration and changes in spring stiffness of the sleeper resilience pad could be cause changes in sleeper support conditions. The damage amount of manganese crossings that occurred during the current service period of about 21 years was investigated to be about 17% of the total amount of crossings, and it was analyzed that the damage amount increased after 15 years of use (accumulated passing tonnage of about 550 million tons). In this study, parameter analysis (wheel position, sleeper support condition, and dynamic wheel load) was performed using a three-dimensional numerical model that simulated real manganese crossing and wheel profile, to analyze the damage type and cause of manganese crossing that occurred in the actual field. As a result of this study, when the voided sleeper occurred in the sleeper around the nose, the stress generated in the crossing nose exceeded the yield strength according to the dynamic wheel load considering the design track impact factor. In addition, the analysis results were evaluated to be in good agreement with the location of damage that occurred in the actual field. Therefore, in order to minimize the damage of the manganese crossing, it is necessary to keep the sleeper support condition around the nose part constant. In addition, by considering the uniformity of the boundary conditions under the sleepers, it was analyzed that it would be advantageous to to replace the sleeper resilience pad together when replacing the damaged manganese crossing.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.5
• /
• pp.813-820
• /
• 1998

This study was performed as a part of comparative biochemical studies of carotenoid pigment for the fresh water fish. Carotenoids in integument of Korean dark sleeper, Odontobutis platycephala, and dark sleeper, Odontobutis odontobutis interrupta, which are all the Korean native fresh water fish, were separated by thin layer chromatography, column chromatography and HPLC. The separated carotenoid were then reduced and isomerized by NaBH4 and I2 respectively to investigate UV-Vis spectrophotometeric patterns and chracterized by IR, 1H-NMR and Mass spectrum. The content of total carotenoids in the integument of Korean dark sleeper was 3.01mg% in April, but it was increased to 3.74mg% in September at the near of spawning period. The carotenoid isolated in April consisted of $\beta$-carotene(25.6%), lutein(18.5%) and zeaxanthin(12.0%) as major carotenoids and also contained isocryptoxanthin, diatoxanthin, tunaxanthin, cynthiaxanthin, canthaxanthin and $\alpha$-cryptoxanthin as minor carotenoids. Similarly, in September the carotenoid consisted of $\beta$-carotene(16.5%), zeaxanthin(13.7%) and cynthiaxanthin(13.6%) as major carotenoids and also contained lutein, isocryptoxanthin, tunaxanthin, $\alpha$-cryptoxanthin, diatoxanthin and canthaxanthin as minor carotenoids. At the near of spawning period, the content of cynthiaxanthin and $\alpha$-cryptoxanthin were increased. The content of total carotenoids in the integument of spawning period. T도 carotenoid isolated in April and September consisted of $\beta$-carotene(24.9%, 27.5%), zeaxanthin(14.4%, 20.9%) and lutein(12.6%, 11.4%) as major carotenoids and also contained cynthiaxanthin, tunaxanthin, diatoxanthin, isocryptoxanthin, $\alpha$-cryp-toxanthin and canthaxanthin as minor carotenoids. At the near of spawning period, the content of zeaxanthin was increased, indicating that the carotenoid composition were dependent upon their living conditions and their integument colors. Both Korean dark sleeper and dark sleeper contained high amount of cynthiaxanthin and diatoxanthin which are found as rare carotenoids in the other of fresh water fish. It is interes that they also contained tunaxanthin which is a specific carotenoid in marine fishes.

• Journal of the Korean Society for Railway
• /
• v.9 no.6 s.37
• /
• pp.746-752
• /
• 2006

The major objective of this study is to investigate the dynamic behavior evaluation of split PC sleepers for railway turnout by the field test. In railway engineering, a turnout is necessary to allow a vehicle to move from one track to another. So, turnout is required very complex railway technologies such as lolling stock, track. In reference to conventional line speed-up and improvement railway, accurate assembly of turnout affects travel ins qualify of turnout area and running safety. Because of heavy weight and a large volume of the long sleeper used to turnout and car limit, transport and the prerequisite for trouble-free transport of the factory pre-assembled major turnout components is achieved through division of long sleepers. The one of the advantages for using a split sleeper is to reduce the dynamic vibration according to the information of developed nations. Therefore, we investigate the characteristic of dynamic behaviors of split sleepers which are adopted for the first time to improve performance of turnout From the field test results of the split sleeper, it is evaluated that the modification of weight, material and stiffness compared with wood sleeper is very effective for the ballast safety. However, the decrease in vibration of split sleeper was not found out.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.9
• /
• pp.620-627
• /
• 2015

Long continuous bridge deck can become contracted considerably as temperature drops, which can lead to a large expansion of sleeper span at the end of it. Since this huge sleeper span then can cause problems both with safety of train operation and structural stability of tracks, it is necessary to take the issue into consideration systematically in the designing process of the bridge. In this paper, an evaluation process through the analysis of train-track interaction was presented which can basically review the effects of the expansion of sleeper span at the end of long continuous bridge deck on the safety of the train and the structural stability of the track. The analyses of the interaction between the light rail train and tracks were carried out targeting the sleeper span as a main parameter. The safety of train operation and structural stability of tracks in a light rail system due to the expansion of the sleeper span were evaluated by comparing the numerical results with the related criteria.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.2
• /
• pp.131-140
• /
• 2022

Installing Continuous Welded Rail (CWR) is one of the economical ways to resolve the challenges of noise, vibration, and the open-deck steel railway bridge impact, and the SSF method using the interlocking sleeper fastener has recently been developed. In this study, the method employed for determining the optimum vertical stiffness of the sleeper pad installed under the bridge sleeper, which is utilized to adjust the rail height and absorb shock when the train passes when the interlocking sleeper fastener is applied, is presented. To determine the optimal vertical stiffness of the sleeper pad, related existing design codes are reviewed, and, running safety, ride comfort, track safety, and bridge vibration according to the change in the vertical stiffness of the sleeper pad are estimated via flexible multi-body dynamic analysis,. The flexible multi-body dynamic analysis is performed using commercial programs ABAQUS and VI-Rail. The numerical analysis is conducted using the bridge model for a 30m-long plate girder bridge, and the response is calculated when passing ITX Saemaeul and KTX vehicles and freight wagon when the vertical stiffness of the sleeper pad is altered from 7.5 kN/mm to 240 kN/mm. The optimum stiffness of the sleeper pad is calculated as 200 kN/mm under the conditions of the track components applied to the numerical analysis.