• Ocean Systems Engineering
• /
• v.6 no.2
• /
• pp.143-159
• /
• 2016

Cargo, such as a Tension Leg Platform (TLP), Semi-submersible platform (Semi), Spar or a circular Floating Production Storage and Offloading (FPSO), are frequently dry-transported on a Heavy Lift Vessel (HLV) from the point of construction to the point of installation. The voyage can span months and the overhanging portions of the hull can be subject to frequent wave slamming events in rough weather. Tie-downs or sea-fastening are usually provided to ensure the safety of the cargo during the voyage and to keep the extreme responses of the cargo, primarily for the installed equipment and facilities, within the design limits. The proper design of the tie-down is dependent on the accurate prediction of the wave slamming loads the cargo will experience during the voyage. This is a difficult task and model testing is a widely accepted and adopted method to obtain reliable sea-fastening loads and extreme accelerations. However, it is crucial to realize the difference in the inherent stiffness of the instrument that is used to measure the tri-axial sea fastening loads and the prototype design of the tie-downs. It is practically not possible to scale the tri-axial load measuring instrument stiffness to reflect the real tie-down stiffness during tests. A correlation method is required to systematically and consistently account for the stiffness differences and correct the measured results. Direct application of the measured load tends to be conservative and lead to over-design that can reflect on the overall cost and schedule of the project. The objective here is to employ the established correlation method to provide proper high-frequency responses to topsides and hull design teams. In addition, guidance for optimizing tie-down design to avoid damage to the installed equipment, facilities and structural members can be provided.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.4
• /
• pp.371-377
• /
• 2012

This paper presents an experimental investigation to figure out slamming impact pressure and flow characteristics of a rectangular Marine structure($800{\times}250{\times}50mm^3$) in free fall. The flow field has been obtained by 2-frame grey level cross correlation PIV(Particle Image Velocimetry) method, the impact pressure of the free fall model by a pressure acquisition system(Dewatron). The angles between a model and the free surface are adapted $10^{\circ}$ and $20^{\circ}$ respectively. Velocity field of water exit has higher better than water entry. The highest point, P2 of impact pressure under the bottom of the model has been appeared about 6 % higher values at 20 degrees than 10 degrees.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.5
• /
• pp.418-424
• /
• 2015

This paper is about the bow structure design of the ship-typed and turret moored FPSO which is subjected to the bow-flare slamming load in harsh North Sea environments. Quad 204 FPSO project involves the redevelopment of the existing Schiehallion FPSO which is damaged by impact wave loads. Normally all offshore systems including FPSO are designed to withstand the 100 year storm I.e. the storm that happens once every hundred years at the location where the system is installed. Several incidents have revealed that impact loading is important issue for moored floating production systems. In this paper, the design impact loads are estimated considering the ship owner’s specification, measured data from model tests, requirements of the classification society rules and results of numerical simulation analyses. The impact pressure by numerical analysis is 1.8 times greater than required value by CSR adopted by IACS. Based on the selected design load, plastic design formulae allowing the local material yielding are applied for the initial scantling of the bow structure. To verify the structural integrity, FE analyses are carried out considering the local area subjected to the impact wave loads. Their results such as structural arrangement, design loads and scantlings are shown and discussed. It is found that plastic design formulae in adopting Initial design phase give sufficiently conservative results in terms of structural strength.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.3
• /
• pp.64-74
• /
• 2002

A special purposed program for ship hull strength analysis considering whipping phenomena is developed. In this program, the non-linear hydrodynamic impact force is considered using the momentum slamming theory and the hull girder is modeled as elastic body on the base of Timoshenko's beam theory. The numerical verifications are conducted in the view points that the effect of slamming impact force, the effect of hydro-elastic formulation, and the effect of various design parameters such as ship speed, wave amplitude, wave length and others. By the application of a real ship design process, the availability of the program is proved. This program has a GUI function for many I/O data process as well as the function to show the 2-D ship motion in the graphic window, and has other available functions for the whipping analysis.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.3
• /
• pp.256-256
• /
• 2017

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.4
• /
• pp.268-268
• /
• 2015

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.4
• /
• pp.390-403
• /
• 2017

Smoothed Particle Hydrodynamics (SPH) method has a good adaptability for the simulation of free surface flow problems. There are two forms of SPH. One is weak compressible SPH and the other one is incompressible SPH (ISPH). Compared with the former one, ISPH method performs better in many cases. ISPH based on Rankine source solution can perform better than traditional ISPH, as it can use larger stepping length by avoiding the second order derivative in pressure Poisson equation. However, ISPH_R method needs to solve the sparse linear matrix for pressure Poisson equation, which is one of the most expensive parts during one time stepping calculation. Iterative methods are normally used for solving Poisson equation with large particle numbers. However, there are many iterative methods available and the question for using which one is still open. In this paper, three iterative methods, CGS, Bi-CGstab and GMRES are compared, which are suitable and typical for large unsymmetrical sparse matrix solutions. According to the numerical tests on different cases, still water test, dam breaking, violent tank sloshing, solitary wave slamming, the GMRES method is more efficient than CGS and Bi-CGstab for ISPH method.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.4
• /
• pp.341-349
• /
• 2018

Recently, it has been reported that the whipping response, which is the elastic phenomenon of the ship, may be one of the causes of the ship accident. Unfortunately, the commonly used methodology for evaluating the whipping effect effectively has not been developed yet. In this study, we developed a procedure to estimate the whipping effect of hull in actual design stage. Fluid-structure interaction analysis was performed for a dominant short term sea state to obtain the time series data of vertical wave bending moment including the whipping response by slamming. In order to estimate the whipping effect by using the time series, some signal processing and statistical techniques such as low pass filtering, Weibull fitting and so on, were applied. the hydro-elasticity analysis was performed on container ships of various sizes to evaluate the whipping effect. The parameters that can affect the response of the hull vibration was selected and the effect of these parameters on whipping was analyzed.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.4
• /
• pp.520-528
• /
• 2018

This paper presents the results of experimental investigation on the elastic-plastic response of steel unstiffened wedges with dead-rise $10^{\circ}$ subjected to repeated impulsive pressure loadings. Repeated drop tests were performed with both wedge thickness and drop height varied. The pressure and histories were recorded during the tests and the permanent deflections were measured after every drop. Using the recorded test result, the effects of flexibility of wedges and repetition have been investigated. From the pressure history obtained from the tests the characteristics of the impulses were identified. Numerical simulations of the tests were made using the measured pressure history and the permanent deflection predictions were compared with those of the experiments.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.24 no.1
• /
• pp.51-66
• /
• 1987

In this paper, the authors investigate theoretically the motion and longitudinal strength of ships among waves talking account of the effects of nonlinearities such as the hull shape, bottom emergence, and hydrodynamic impact. Incidentally the ship is treated as an elastic beam in heading wave condition regarding characteristics of slamming and whipping-according to the variation in the range of a quarter length of the ship forward and the increase of the elastic modes up to 4-th vibration mode were investigated by the present theory. Calculations are performed for 97m container ship and its validity is confirmed by a series of model tests. Conclusions obtained are as follows; 1) Acceleration and pressure estimated by the present theory are in good accordance with experiments. 2) The present non-linear theory may be applied for estimating longitudinal bending moment of ships in slamming and whipping conditions. 3) In investigation of the characteristic in response according to shape variation for parts under draft and vow-flare in the range of a quarter length of the ship forward, dynamic responses due to the former were much more conspicuous than those due to the later. 4) In the maximum bending moment, the considering case up to 2-the mode are larger, about $10{\sim}15%$, than that up to 4-th mode.