• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.57-66
• /
• 2006

AA5182-polypropylene sandwich sheet was manufactured, and the mechanical properties evaluation was executed in order to identify $L{\ddot{u}}ders$ band that causes fabrication process problem and especially surface roughness. To identify formability, deformation behavior, plastic strain ratio (R-value) and pole figure were measured, and texture analysis was performed. In the case of sandwich sheet, the unstable deformation behavior has decreased. As well, for sandwich sheet, A1 skin could manage the most of load, and the elongation has improved about 45% more than that of A1 skin. The plastic strain ratio of A1 skin and sandwich panel, which indicates serration behavior, was obtained from instantaneous plastic strain ratio evaluation. Also, the planar anisotropy of sandwich sheet has decreased more than that of A1 skin. According to these results, the sandwich sheet produced lightening effect and could control unstable deformation characteristic, that is, surface roughness caused by $L{\ddot{u}}ders$ band. Furthermore, it was proved that the texture control of the rolling attachment of A1 skin is necessary to improve the formability of the sandwich panel.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.317-317
• /
• 2000

The mathematical set-up model was developed to reduce the mechanical property deviation in annealed and slightly rolled steel strip. The mechanical peculiarities of temper rolling process, such as high friction value and non-circular contact arc, Low reduction and non-negligible entry and exit elastic zones as well as central restricted deformation zone are all taken into account. The deformation of work rolls is calculated with the influence function method and arbitrary contact arc shape is permitted. The strip deformation is modeled by slab method and the entry and exit elastic deformation zones are included. The restricted deformation Bone near the neutral point is also considered. It was revealed that the new model has better accuracy than present regression model by statistical analysis with actual mill rolling data.

• Composites Research
• /
• 제18권1호
• /
• pp.30-37
• /
• 2005

본 연구에서는 3점 굽힘 실험과 코어의 실제 형상을 모델링한 유한요소 시뮬레이션을 병행하여 외피층의 항복, 층간분리 코어의 전단 및 국부적 좌굴과 같은 다양한 파손모드를 고려한 하니컴 샌드위치 복합재료의 강도 특성과 변형거동을 검토하였다. 외피층과 하니컴 코어층 사이를 완전 접착한 시험편과 부분 층간분리 시험편을 대상으로 하니컴 코어의 셀 크기와 외피층 두께를 변화시켜 시험편의 굽힘 강성, 굽힘 강도. 굽힘 응력, 변형 및 파손 거동을 해석하였다. 결론적으로 하니컴 코어의 셀 크기와 외피층의 두께가 하니컴 샌드위치 복합재료의 굽힘 강성과 강도, 변형/파괴 거동에 주된 영향을 미쳤으며 코어의 셀 크기가 크고 외피층의 두께가 얇은 경우 굽힘 강도는 $30\~68\%$ 정도까지 저하됨을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제31권2호
• /
• pp.38-44
• /
• 2003

플로쉬문은 우리나라에서 가장 일반적으로 사용되는 문으로서 가정용으로부터 영업용 문까지 그 용도가 다양하다. 플러쉬문의 제작방법은 거의 변화가 없이 남양재 골조 위에 합판덮개를 덮어서 본체를 구성하는 형태가 계속 사용되고 있다. 그러나 목재 시장과 판재 시장의 수요와 공급 상황이 변하기 때문에 이에 맞추어서 플러쉬문의 제작에 사용되는 재료의 선택도 달라져야 할 것이다. 이 연구에서는 플러쉬문의 제작에 HDF를 덮개 및 골조재료로 사용하고자 하였으며 일반적인 제작방법에 의하여 생산된 스킨문과 그 성능을 비교하였다. 시험용 문들을 여름과 겨울의 계절에 따라서 변하는 실내의 온도 및 습도환경에 3-4개월 동안 노출시키고 문의 변형과 온도 및 상대습도를 1주일 단위로 측정하였다. 이 연구의 결과로부터 HDF가 플러쉬문의 덮개 및 골조용 재료로 사용될 수 있음을 알 수 있었으며 이 연구에서 개발된 골조의 구성방법에 의하여 생산된 플러쉬문이 일반적인 스킨문보다 매우 우수한 성능을 나타내었다. 문의 변형은 온도 및 상대습도가 증가할수록 증가하는 경향을 나타내었으며 플러쉬문이 전반적으로 스킨문보다 적은 변형을 나타냄으로써 환경변화에 대응하여 스킨문보다 안정적이고 좋은 성능을 나타냄을 알 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.995-996
• /
• 2010

• 한국생활과학회지
• /
• 제21권3호
• /
• pp.551-565
• /
• 2012

The primary goal of this study was to provide a systematic methodology of utilizing 3D technology for tight-fit performance sportswear using information of skin deformation in various posture. Technical tools used in this study are Cyberware whole body scanner, RapidForm2004, 2C-AN 3D pattern development program, and YukaCAD. Analysis of the 3D skin deformation while knee joint was bent from $0^{\circ}$ to $60^{\circ}$ revealed that the length of dermatomes L4 was remained consistent during knee bending. Therefore, L4 was chosen as a major cutting line. To develop a highly ergonomic pattern, replicas of static and dynamic postures were developed and integrated using two methods, one is morphing method (Sqirlz Morph), and the other is AutoCAD. Experimental tight-fit garments called 'Derm-Mov Pattern' was designed using dematomes L4, L2, and inner line under knee and compared with four other patterns. As results, AutoCAD was appropriate as a integrating method of various postures. In wear test, 'Derm-Mov Pattern' was rated high (p < .001), in terms of pressure comfort especially around front crotch area. However, wear sensation was not signipicantly different in other area due to highly extensible property of materials. Pressure distribution was relatively even in these experimental garments.

• 한국생활과학회지
• /
• 제24권5호
• /
• pp.687-700
• /
• 2015

Lines of non-extension (LoNEs) on torso surface during arm abduction were investigated to provide appropriate location for inserting less-extensible yarns which can be used as seams for design and or clothing pressure variation. As experimental methods, reference points about 3 cm apart were marked on the skin and scanned at 30, $90^{\circ}$ and $135^{\circ}$ arm abduction. Skin deformation was measured by connecting reference points in horizontal, vertical and various angles of diagonal directions. Observation of skin deformation was made within the separated sections of the torso as well as integrated ones to cover the various occasions of design application. LoNEs of front and back torso were provided as mapping lines. Actual compression wear of three types was constructed with different pattern reduction rate at each separated section using LoNEs as boundary cutting lines. Clothing pressure and subjective evaluations of those three compression wear were evaluated by six subjects. LoNEs found in this study were useful as seam lines to differentiate clothing pressure at each part of the body, providing positive wear sensation. It is also expected that LoNEs can be paths for less strechable conductive yarns of IT-integrated upper garments.

• Archives of Pharmacal Research
• /
• 제28권4호
• /
• pp.458-462
• /
• 2005

The water content of skin was determined using a FT near infrared (NIR) spectrometer. NIR diffuse reflectance spectra were collected from hairless mouse, in vitro, and from human inner arm, in vivo. It was found that the variation of NIR absorbance band 1450 nm from OH vibration of water and 1940 nm from the combination involving OH stretching and OH deformation, depending on the absolute water content of separated hairless mouse skin, in vitro, using the FT NIR spectrometer. Partial least squares regression (PLSR) was applied to develop a calibration model. The PLS model showed good correlation. For practical use of the evaluation of human skin moisture, the PLS model for human skin moisture was developed in vivo on the basis of the relative water content of stratum corneum from the conventional capacitance method. The PLS model predicted human skin moisture with a standard errors of prediction (SEP) of 3.98 at 1130-1830 nm range. These studies showed the possibility of a rapid and nondestructive skin moisture measurement using FT NIR spectrometer.

• 패션비즈니스
• /
• 제20권3호
• /
• pp.17-29
• /
• 2016

To develop baseball catcher leg guards, 3-dimensional (3D) methodologies, which are 3D human body data, reverse engineering, modeling, and printing, optimized guard design for representative positions. Optimization was based on analysis of 3D body surface data and subjective evaluation using 3D printing products. Reverse engineering was used for analysis and modeling based on data in three postures: standing, $90^{\circ}$ knee flexion, and $120^{\circ}$ knee flexion. During knee flexion, vertical skin length increased, with the thigh and knee larger in anterior area compared to the horizontal dimension. Moreover, $120^{\circ}$ knee flexion posture had a high radius of curvature in knee movement. Therefore, guard designs were based on increasing rates of skin deformation and numerical values of radius of curvature. Guards were designed with 3-part zoning at the thigh, knee, and shin. Guards 1 and 2 had thigh and knee boundaries allowing vertical skin length deformation because the shape of thigh and knee significantly affects to its performance. Guard 2 was designed with a narrower thigh and wider knee area than guard 1. The guards were manufactured as full-scale products on a 3D printer. Both guards fit better in sitting than standing position, and guard 2 received better evaluations than guard 1. Additional modifications were made and an optimized version (guard 3) was tested. Guard 3 showed the best fit. A design approach based on 3D data effectively determines best fitting leg guards, and 3D printing technology can customize guard design through immediate feedback from a customer.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.752-757
• /
• 1991

Recently, human body modeling with muscle deformation has become an attractive research area in computer animation. There are many modeling tools available for solids such as mechanical part. However, there are many limitations of these conventional methods in modeling flexible objects with delicate motions and shapes such as human bodies. In this paper we present a new modeling technique for human body with muscle deformation. Each muscle is represented as a generalized cylinder and its shape deformation is computed using simple algorithm. The human body is a union of muscles, bones, organs, etc. The modeling data are obtained from the information on the human anatomy. To demonstrate the feasibility of our method, we model several arm muscles and simulate the skin deformation. As a result we have obtained a realistic shape deformation.