• Journal of Bio-Environment Control
• /
• v.24 no.2
• /
• pp.100-105
• /
• 2015

The calculation method of infiltration loss in greenhouse has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the infiltration rates using the tracer gas method in plastic greenhouses equipped with various thermal curtains. And then the calculation methods of infiltration loss in greenhouses were reviewed. Infiltration rates of the multi-span and single-span greenhouses were measured in the range of $0.042{\sim}0.245h^{-1}$ and $0.056{\sim}0.336h^{-1}$ respectively, single-span greenhouses appeared to be slightly larger. Infiltration rate of the greenhouse has been shown to significantly decrease depending on the number of thermal curtain layers without separation of single-span and multi-span. As the temperature differences between indoor and outdoor increase, the infiltration rates tended to increase. In the range of low wind speed during the experiments, changes of infiltration rate according to the outdoor wind speed could not find a consistent trend. Infiltration rates for the greenhouse heating design need to present the values at the appropriate temperature difference between indoor and outdoor. The change in the infiltration rate according to the wind speed does not need to be considered because the maximum heating load is calculated at a low wind speed range. However the correction factors to increase slightly the maximum heating load including the overall heat transfer coefficient should be applied at the strong wind regions. After reviewing the calculation method of infiltration loss, a method of using the infiltration heat transfer coefficient and the greenhouse covering area was found to have a problem, a method of using the infiltration rate and the greenhouse volume was determined to be reasonable.

• Korean Journal of Agricultural Science
• /
• v.28 no.2
• /
• pp.99-107
• /
• 2001

It is difficult to install a ventilation window on the roof of single span greenhouses of arch shape. Investigation on the roof ventilation structures for those greenhouses was conducted. In small greenhouses with spans of 5 to 8 m, circular or chimney type ridge vents made of plastic were employed. In large greenhouses with spans of 12 to 18 m, even span roll-up ridge vents made of steel pipe were employed. The effect of roof ventilation was evaluated by comparative experiments between greenhouse installing ridge vents and having controlled side vents only. Roof ventilation contributed greatly to restraint of temperature rise and maintenance of uniform temperature distribution in greenhouses. And ventilation efficiency was analyzed by experiments on the opening and closing operation of the ridge and side vent. There were no temperature differences according to opening and closing sequence of ventilation window. But for greenhouse temperature control by ventilation, it is desirable to open side vents after ridge vents and to close ridge vents after side vents.

• Journal of Bio-Environment Control
• /
• v.31 no.2
• /
• pp.90-97
• /
• 2022

This study was carried out to investigate the effect of side vent heights on temperature and relative humidity inside and outside the single-span plastic greenhouse (W: 7 m, L: 40 m H: 3.9 m) during natural ventilation. Four different heights (120, 100, 80, 60 cm) of the side vent were used as an experimental condition. Variations of temperature and relative humidity inside and outside the greenhouse and the differences between heights were compared by using one-way ANOVA. In the daytime, the difference in temperature between inside and outside the greenhouse was dropped from 14.0℃ to 7.1℃ as the side vent height increased. The temperature difference in the nighttime was less than 0.2℃ regardless of the height. One-way ANOVA on the temperature difference between heights presented that the statistical significance was founded between all of the combinations of height in the daytime. The difference in relative humidity between inside and outside the greenhouse was grown from -13.8% to -22.2% with a decrease in the side vent height. The humidity difference in the nighttime was less than 1% regardless of the height. One-way ANOVA on the humidity difference revealed that most of the side vent heights showed significance in the daytime but between 100 and 80 cm was not significant. It seemed because the external air became cooler during the experiment with a height of 80 cm. Conclusively, this study empirically demonstrated that the higher side vents resulted in the decrease of differences in temperature and relative humidity between inside and outside the greenhouse, and also the effect of side vent height was statistically significant. This study may be helpful for deciding the height of the side vent effective for controlling temperature and relative humidity in a single-span greenhouse during natural ventilation.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.3
• /
• pp.47-55
• /
• 2010

Investigations on the inundation damage and improvement measures were carried out centering around the protected horticultural complex concentrated in lowlands on the side of Geum river, in Nonsan and Buyeo, Chungnam. Most greenhouses were single-span plastic houses in this area, and tomato, strawberry and watermelon were cultivated mainly. 45.8 % of whole farmhouse were experienced in damage by inundation, and a frequency of the damage was average once in 11 years. The most urgent problem at the greenhouse culture in this area was showed in order of drainage improvement, irrigation water resources and energy saving. Consideration items in drainage improvement project for protected horticulture were showed in order of extending drain pumps, extending drain canals, using concrete flume in drain ditch. It needs to consider systematic plans that can restrain new establishment of greenhouses on the lowland paddy field in drainage area. It is difficult to remove greenhouses which are already established or prohibit cultivation. Therefore we should impose minimum duty items so that greenhouse tillers can cope with inundation. And it is thought that managing agency need to minimize farmers damage by improving drainage ability and introducing maintenance pattern that is different from rice cropping.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.60 no.4
• /
• pp.105-111
• /
• 2018

Institutional inertia anti-disaster standard was presented mainly on the upper surface, it is necessary to improve to the soil type standard and uplift the resistance standard greenhouse that are vulnerable to strong winds. In this study, we carried out a field test using the load control method in order to evaluate the uplift resistance of continuous foundation of greenhouse with different depths of the rafters. Institutional inertia anti-disaster standard of greenhouse foundation did not protect the greenhouse structure from the damages caused by strong winds and heavy snow. Therefore, field tests for behavior characteristics of continuous greenhouse foundation were carried out to ensure stable facility cultivation. The field test condition was evaluated using different embedded depth as follows: 30cm, 40cm, 50cm and spacing 50cm, 60cm, 70 cm. As a result of the uplift resistance field tests using the load control method, the minimum uplift resistance was found to be over 90kg and uplift resistance displacement was 9.4mm. Uplift resistance of the continuous greenhouse foundation was in the range of 90-180 kg according to embedded depth and spacing. Using the test condition, there was no constant trend in the uplift resistance.

• Journal of Bio-Environment Control
• /
• v.24 no.4
• /
• pp.308-316
• /
• 2015

This study was conducted to investigate the situation of ICT apply to plastic greenhouse, and the results be apply to design of new one. A CFD analysis were conducted to monitering the ventilation and energy saving of the single span greenhouse newly designed. The causes of delay to apply ICT to plastic greenhouse are the high cost for installation(24%), insufficiency of after services(19%), often disorder(16%), unskillful management of soft ware(15%), insufficient ICT efficiency(13%) and unsatisfying of income increase(12%). The parts of problem occurred in ICT plastic greenhouse are the structure, actuator, environmental control system and sensor(approximate 14%, respectively), remote control technique(13%), plant management technique(12%), energy saving technique(10%) and utilization of software(8%). In the condition of lateral window closed, the average wind speed changed to slow, but it was faster in the condition of leeward side window opened than in the condition of lee and winward side window opened. The air movement in the condition of lateral window closed occur by air moving fan not by out air. It is not affect the room temperature but effective the uniformity of room temperature. The average temperature of low height greenhouse was uniform than high height one. The average temperature in condition of 3rd curtain opened become same with outside temperature after 2 hours, but take more 5 hours in condition of 3rd curtain closed.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.283-290
• /
• 2017

In this study, the method to attach plastic film on the side vent from inside of greenhouse for the entire length was developed as the way to make crops less stressful while uniformly getting outside air into the greenhouse when ventilating using roof ventilation fans at single-span plastic greenhouse for oriental melon in a low-temperature period. The plastic film was installed from ground to 10cm below from the height where side vent is fully opened. In order to verify that the improved side vent can improve greenhouse environment and fruit yield, it was compared with the control plot of conventional side vent. Both greenhouses were not ventilated until February 25th, 2017. Air temperature in both greenhouses exceeded $40^{\circ}C$ in mid February. Therefore, it is judged that the greenhouse should be ventilated from mid February. Air temperature in the control plot exceeded $30^{\circ}C$ from late April. Therefore, it is judged that the plastic film attached to the inside of side vent should be removed in late April, or in early May at the latest. Soil temperature in the treatment plot in the mid Aril exceeded $20^{\circ}C$, which is suitable for growth, while that in the control plot was still below $20^{\circ}C$. Soil temperature in the control plot finally exceeded $20^{\circ}C$ in late April. The consumption of electricity was 47.2 kWh in the treatment plot, and 48.3 kWh in the control plot, which was no significant difference. The marketable yield of oriental melon in the treatment plot was 5,094kg, which was 23.9% more than that in the control plot, 4,113kg. The marketable fruit ratio was 73.5% in the treatment plot, and that in the control plot was 73.9%, which was no significant difference.

• Journal of Bio-Environment Control
• /
• v.23 no.2
• /
• pp.95-108
• /
• 2014

The objective of this study is to develop the plastic greenhouse models which are structurally safe under the weather condition of Seongju and have the dimensions suitable for oriental melon cultivation as well. To grasp the structural features of greenhouses in Seongju, the field survey was conducted on 406 farmhouses which included 2,068 greenhouses. The field survey showed that the roof shape of arch type accounted for the highest rate, but recently even span or peach type became more popular and the width and height of greenhouse tended to increase as the period of use was short. The relationship of the width, ridge height and eaves height were established based on field survey data. Using climate data of Gumi adjacent to Seongju, the regressions were determined for the design wind speed and design snow depth depending on recurrence period. To design the greenhouse models against weather disasters in Seongju, the optimal design loads are 23.7 cm of snow depth and $33.8m{\cdot}s^1$ of wind speed. As the design results, four models of single-span greenhouse, two models of double-span greenhouses including extension were developed.

• Journal of Bio-Environment Control
• /
• v.29 no.1
• /
• pp.73-79
• /
• 2020

The objective of this study is to analyze the heat transfer loss of covering materials in a single-span plastic greenhouse under the steady-state wind environment. To achieve this objective, the following were conducted: (1) design of a small-scaled wind tunnel (SCWT) to analyze heat losses of the greenhouse and its performance; (2) determination of the overall heat transfer coefficient (OHTC) for the covering materials using a small-scaled greenhouse model. The SCWT consists of the blowing, dispersion, steady flow, reduction and testing areas. Each part of the SCWT was customized and designed to maintain air flow at steady state and to minimize the variances in the SCWT test. In this study, the OHTCs of the covering materials were calculated by separating each with the roof, side wall, front and back of the small-scaled greenhouse model. The results of this study show that the OHTC of the roof increases as wind speed increases but the zones in which the increase rate of the OHTC decreased, were distinguished by wind tunnel wing speed of 2 ms^-1. For the side wall, the increase rate of the OHTC was particularly higher in the 0-1 ms^-1 zone.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.279-279
• /
• 2017

In Korea, the single span unheated plastic house cultivated crops from autumn to spring of the following year, removed the plastic film and frame, cultivated rice, set up a plastic house again and cultivated crops. The crops in the greenhouse are utilized mainly for the production of leaf vegetables such as lettuce, leek, and fruit vegetables such as strawberry, watermelon, oriental melon, etc. and raising high income. Because, the production of these crops has characteristics requiring a lot of labor and it is difficult to produce horticultural crops at unheated plastic houses as the rural population ages. Therefore, we conducted a test to develop a crop planting system to cultivate crops in single span unheated plastic houses, although the utilization of labor is less than that of horticultural crops. The prior cropping cultivated three cultivars of sweet potatoes early, the second produced cultivated sweet potatoes, corn and soybeans. In the cultivation of the previous cropping, the sweet potatoes were harvested on the 113th day after planting on March 30th, the yield was 822 kg/10a for Pungwonmi, 1,377 kg/10a for Jinhongmi, 1,483 kg/10a for the Dahomi. Because of differences, the yield of Pungwonmi cultivar was less than that other cultivars and the yield of open field cultivations, we will expect further research. In the cultivation of the succeeding crops sweet potatoes were planted on July 27 and harvested 110 days later and investigated. The product yield of Pungwonmi cultivar was 1,024 kg/10a, and the Jinhongmi, Dahomi cultivars were not at economic level for sale and were necessary to review. In succeeding-crops, corn tested the Ilmichal cultivar, seeded on 27th July, harvested on October 11th. The day of silking was 45 days after sowing, the yield was 1,156 kg/10a, the goods rate was 100% level. The beans in the succeeding cultivation crop were sowed on 27th July, the early maturing of the varieties coming to Hwangeumol and Saeol cultivar, on 17th October, the late maturing soybean Daewonkong cultivar were harvested on October 21st. The yield of early maturing two cultivars was 214 kg/10a, Daewonkong was 257 kg/10a, and 100 seeds weight which were more than the early maturing beans were also heavy. When calculating these incomes price-wise according to the harvest time, we were able to consider the income in the order of corn, sweet potato and soybean from the second term crop. Various studies such as varieties, mulching method, moisture management, control environment management, etc. are considered necessary to develop cropping systems with sweet potato and field crops in future unheated plastic house.