• 한국해양공학회지
• /
• 제1권2호
• /
• pp.74-82
• /
• 1987

This study has been made to investigate into the behavior of fatigue limit, of fatigue crack initiation, and of fatigue crack propagation under the condition of rotating bending stress; specifically on the independency of stress field as well as the crack behavior of surface micro hole defect, which is made artificially through the specimen. The results obtained can be summarized as followa; 1) For the single micro hole defect, initiation of fatigue crack is occurred at both tips of microhole defect simultaneosly along the slip which are produced in the range of maximum principal stress arround micro hole defect independent of the size of micro hole defect. 2) For the neighbored deuble micro hole defects with equal size, in the range ($\frac{L}{r}$)ratio $\gtrsim$ 3 defined as the size of micro hole defect(2r) to the distance between the centers of micro hole defects (2L), the crack behavior of the micro hole defects is same as single one. However, for the range of $\frac{L}{r}$<3, the interference effect becomes significant as the ratio approaches to 1.

• 한국진공학회지
• /
• 제10권2호
• /
• pp.257-261
• /
• 2001

InGaAs/GaAs 초격자 구조들 사이에 InAs/GaAs 양자점을 MBE로 성장하고 광특성을 측정한 결과 매우 균일한 양자점을 얻을 수 있었다. Self-consistent한 이론 계산으로부터 얻은 p-i-n 구조의 최적 조건으로 단일광자구조를 성장하고 단일광자소자를 e-beam lithography를 이용하여 제작하였다. 전기적 특성인 I-V곡선에서 나타난 전기 이력현상으로부터 단일 전자와 단일 정공이 다른 전압에서 투과하여 단일 전자-정공 재결합 현상이 나타나고 있음을 확인하였다.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.65-72
• /
• 1998

The BTA drilling chip is better for deep hole drilling than other self-piloting with pad drilling chips because the large length to diameter ratio allows a unique cutting force dispersion and better supplies the high pressure fluid. Therefore the BTA is useful for many tasks, such as coolant hole drilling of large scale dies, as well as tube seat drilling, which is essential for the heat exchanger, and variable component drilling for automobiles. Deep hole drilling has several significant problems, such as hole deviation, hole over-size, circularity, straightness, and surface roughness. The reasons for these problems, which often result in quality short comings, are an alignment of the BTA drilling system and the unbalance of cutting force by work piece and tool shape. This paper analyzes the properties through an experiment which com¬pared single-edge BTA drills with multiple-edge BTA drills, as well as the shapes of the tools to cause an unbalance of cutting force, and its effect on the precision of the worked hole. Conclusions are as follows. 1) In SMSSC drilling, 60m/min of BTA with single and multi-edged tools proved the best cutting condition and the lowest wear character. 2) The roundness got a little worse as cutting speed was increased, but surface roughness was hot affected. 3) It was proved that the burnishing torque of both drills approached 26%. which is almost the same as the 24% insisted on by Griffiths, and the dispersion characteristic of the multi-edged BTA drill proved better than the single-edge BTA drill.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.13-13
• /
• 2010

Switching an elementary excitation by injecting a single carrier would offer the exciting opportunity for the ultra-high data storage technologies. However, there has been no methodology available to investigate the interaction of low energy discrete carriers with nano-structures. In order to map out the spatial dependency of such single carrier level interactions, we developed a pulse-and-probe algorithm, combining with low temperature scanning tunneling microscopy. The new tool, which we call single carrier spectroscopy, allows us to track the interaction with the target macrostructure with tunneling carriers on a single carrier basis. Using this tool, we demonstrate that it is possible not only to locally write and erase individual bi-solitons, reliably and reversibly, but also to track of creation yields of single and multiple bi-solitons. Bi-solitons are pairs of solitons that are elementary out-of-phase excitations on anti-ferromagnetically ordered pseudo-spin system of Si dimers on Si(001)-c(42) surfaces. We found that at low energy tunneling the single bisoliton creation mechanism is not correlated with the number of carriers tunneling, but with the production of a potential hole under the tip. An electric field at the surface determines the density of the local charge density under the tip, and band-bending. However a rapid, dynamic change of a field produces a potential hole that can be filled by energetic carriers, and the amount of energy released during filling process is responsible for the creation of bi-solitons. Our model based on the field-induced local hole gives excellent explanation for bi-soliton yield behaviors. Scanning tunneling spectroscopy data supports the existence of such a potential hole. The mechanism also explains the site-dependency of bi-soliton yields, which is highest at the trough, not on the dimer rows. Our study demonstrates that we can manipulate not just single atoms and molecules, but also single pseudo-spin excitations as well.

• Nuclear Engineering and Technology
• /
• 제37권6호
• /
• pp.557-564
• /
• 2005

Air-water countercurrent flow limitation at perforated plates with four holes was investigated in a vertical tank to see the effects of the plate thickness, the number of hole, and the diameter of the hole on the onset of CCFL. The thickness of plates was 1 cm and 4 cm, with a relatively large hole diameter of 5 cm. The collapsed water level formed on the perforated plate and its distribution in the upper plenum were measured. The gas flow rate in the multi-hole plate is relatively higher than one in the single tube because some of holes in the multi-hole plate provide a flow path fur liquid with less air-liquid resistance than in the single tube. The onset of CCFL occurred at nearly the same air flow rate regardless of the plate thickness. The negligible effect of the plate thickness on CCFL means that the flooding is initiated at the top of the plate rather than at its bottom. It turns out that $j_k$ and $K_k$ better fit the data than $H_k$ when hole diameter is greater than 2.86 cm. In our experimental ranges, the collapsed water levels at the onset of CCFL ranged from 7.5 cm to 10.5 cm. There was no three dimensional distribution of water level before and after the onset of CCFL.

• ETRI Journal
• /
• 제34권6호
• /
• pp.950-953
• /
• 2012

Schottky barrier single electron transistors (SB-SETs) and Schottky barrier single hole transistors (SB-SHTs) are fabricated on a 20-nm thin silicon-on-insulator substrate incorporating e-beam lithography and a conventional CMOS process technique. Erbium- and platinum-silicide are used as the source and drain material for the SB-SET and SB-SHT, respectively. The manufactured SB-SET and SB-SHT show typical transistor behavior at room temperature with a high drive current of $550{\mu}A/{\mu}m$ and $-376{\mu}A/{\mu}m$, respectively. At 7 K, these devices show SET and SHT characteristics. For the SB-SHT case, the oscillation period is 0.22 V, and the estimated quantum dot size is 16.8 nm. The transconductance is $0.05{\mu}S$ and $1.2{\mu}S$ for the SB-SET and SB-SHT, respectively. In the SB-SET and SB-SHT, a high transconductance can be easily achieved as the silicided electrode eliminates a parasitic resistance. Moreover, the SB-SET and SB-SHT can be operated as a conventional field-effect transistor (FET) and SET/SHT depending on the bias conditions, which is very promising for SET/FET hybrid applications. This work is the first report on the successful operations of SET/SHT in Schottky barrier devices.

• 한국항공우주학회지
• /
• 제34권5호
• /
• pp.30-38
• /
• 2006

기존의 전통적인 회귀분석 기반 교정방법에 비해 높은 교정정밀도를 얻을 수 있는 5-hole pressure probe의 교정방안을 연구하였다. 이 새로운 교정기법은 교정시험으로부터 획득한 데이터와 곡선적합 결과간의 차이를 이용하여 산정한 단일 영역에 대한 오차보간 반응곡면을 사용한다. 끝단의 직경이 4.0 mm인 5-hole probe를 자체 제작하고, 레이놀즈수$4.11{\times}10^6$/m와 흐름각 ${\pm}48$에서 교정시험을 수행하였다. 최소자승 회귀분석모델과 단일영역 오차보간 모델을 적용하여 자료처리를 수행하고 이들 두 교정방안에 대한 비교평가와 분석을 수행하였으며, 아울러 교정 정밀도에 대한 평가도 수행하였다.

• 한국지반환경공학회 논문집
• /
• 제25권7호
• /
• pp.5-19
• /
• 2024

During the blasting process, a fracture zone is formed in the vicinity of the blast hole. Any damage that extends beyond the excavation boundary line necessitates the implementation of an additional support system to assure safety. Typically, fracture zone radius is estimated from blast hole pressure using theoretical methods due to its simplicity. However, linear charge concentration (kg/m) is used for tunnel blasting. This paper compiles Swedish experimental datasets to estimate the radius of fracture zones based on linear charge concentration. Further numerical analyses are performed in LS-DYNA for coupled single-hole blasting. The Riedel-Hiermaier-Thoma (RHT) model has been selected as the constitutive model for this investigation. The numerical model is validated against small-scale laboratory tests. Parametric studies are conducted to predict fracture zones in granite and sandstone rocks using two kinds of explosives, PETN and AFNO. The analyses evaluate ten types of blast hole sizes, ranging from 17 to 100 mm. The results indicate that granite has a larger fracture zone than sandstone, and the PETN explosive predicts more damage than ANFO. Smaller blast holes exhibit smaller fracture zones in comparison to larger blast holes. Wave propagation is more rapidly attenuated in granite than in sandstone. Subsequently, the predicted fracture zone outcomes are compared with the empirical dataset. Fracture zones of medium blast hole diameter align well with the experimental data set. A predictive equation is derived from the data set, which may be used to evaluate blast design to manage fracture zones beyond the excavation line.

• 동력기계공학회지
• /
• 제12권5호
• /
• pp.14-19
• /
• 2008

In order to meet stringent future emission regulations, especially to reduce Particulate Matter (PM) and NOX, stoichiometric diesel combustion technology with a piezo group-hole nozzle injector is being researched for reduction harmful emissions. A new nozzle layout, namely a group-hole nozzle, which has one group of small orifices with a wide spray included angle was investigated to improve the efficiency of stoichiometric diesel combustion. From this point of view, the group-hole nozzle suggested by Dense Co. is an attractive candidate method applicable to stoichiometric diesel combustion. The group-hole nozzle concept is to reduce the injector nozzle hole diameters without sacrificing spray penetration by closely locating two holes. Experimental studies have proven that the spray from group-hole nozzles have similar spray penetration to that of a single hole with equivalent overall nozzle hole area, but the spray drop sizes (SMD) are reduced, aiding vaporization and mixing.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.215-219
• /
• 2005

Liquefied petroleum gas (LPG) has been used as motor fuel due to its low emissions and low cost. A liquid direct injection system into a cylinder was suggested as a next generation system to maximize a fuel economy as well as a power. This study addresses the analysis of the LPG spray injecting from single hole injector. Two different test conditions are given, which are a fully developed spray case with various injection pressures and a developing spray case with ambient pressure variation. The LPG spray photographs are compared with the sprays of gasoline and diesel fuel at the same conditions, and the spray angles and penetration lengths are also compared, and then the spray behavior is analyzed. The LPG spray photos show that the dispersion characteristic depends very sensitively on the ambient pressure soon after injection. The spray angle is very wide in a low ambient pressure condition until the saturated pressure, but the angle is quickly reduced at the condition over the pressure. However, the down stream of the LPG spray shows much wider dispersion and less penetration than those of gasoline and diesel sprays regardless ambient pressure condition.