• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.225-229
• /
• 2008

We present an intelligent forging simulator AFDEX. The intelligent forging simulator is determined by the adaptive and optimal mesh generation technique and many intelligent application-oriented special functions which minimize the user-intervention during forging simulation. Of course, the solution accuracy should be optimized in the intelligent simulation. We have developed AFDEX to meet the requirement on intelligent simulation. Its characteristics are introduced with the help of typical application examples.

• Journal of the Korea Computer Graphics Society
• /
• v.23 no.1
• /
• pp.25-32
• /
• 2017

This paper proposes a novel acceleration method for particle based large scale fluid simulation. Traditional particle-based fluid simulation has been implemented by interacting with physical quantities of neighbor particles through the Smoothed Particle Hydrodynamics(SPH) technique[1]. SPH method has the characteristic that there is no visible change compared to the computation amount in a part where the particle movement is small, such as a calm surface or inter-fluid. This becomes more prominent as the number of particles increases. Previous work has attempted to reduce the amount of spare computation by adaptively dividing each part of the fluid. In this paper, we propose a technique to calculate the motion of the entire particles by using the physical quantities of the near sampled particles by sampling the particles inside the fluid at regular intervals and using them as reference points of the fluid motion. We propose a technique to adaptively generate a triangle map based on the position of the sampled particles in order to efficiently search for nearby particles, and we have been able to interpolate the physical quantities of particles using the barycentric coordinate system. The proposed acceleration technique does not perform any additional correction for two classes of fluid particles. Our technique shows a large improvement in speed as the number of particles increases. The proposed technique also does not interfere with the fine movement of the fluid surface particles.

• The Transactions of the Korea Information Processing Society
• /
• v.1 no.2
• /
• pp.244-253
• /
• 1994

Computer networks need a variety of services. Some services such as, video, voice and plantcontrol traffic require a real-time communication with explicit timing constraints. In this pater, we introduce a real-time communication technique which use a reservation technique on dualilnk networks. We introduce an enhanced technique that determines priorities of the message based on time constraints when real-time messages are transmitted. A simulation was conducted to compare and to analyze traditional technique. We used the SLAM II language to simulate this technique. Message loss rate were compared and analyzed as a performance criteria in this simulation.

• Wind and Structures
• /
• v.14 no.5
• /
• pp.465-480
• /
• 2011

In this paper, a stabilized large eddy simulation technique is developed to predict turbulent flow with high Reynolds number. Streamline Upwind Petrov-Galerkin (SUPG) stabilized method and three-step technique are both implemented for the finite element formulation of Smagorinsky sub-grid scale (SGS) model. Temporal discretization is performed using three-step technique with viscous term treated implicitly. And the pressure is computed from Poisson equation derived from the incompressible condition. Then two numerical examples of turbulent flow with high Reynolds number are discussed. One is lid driven flow at Re = $10^5$ in a triangular cavity, the other is turbulent flow past a square cylinder at Re = 22000. Results show that the present technique can effectively suppress the instabilities of turbulent flow caused by traditional FEM and well predict the unsteady flow even with coarse mesh.

• Transactions of Materials Processing
• /
• v.4 no.1
• /
• pp.9-16
• /
• 1995

Model material technique, which requires only the small space of experimental set-up and low cost for experiment, is used to estimate the deformed profile and the forging load in rotary forging. The materials and working conditions are determined to satisfy the similitude conditions between the model test and the prototype test. The model material of the so-called plasticine and the mild steel are chosen as specimens, and they represent almost the same value of strain gardening exponent in the stress-strain relationship. Lubricant in the model test is also carefully selected so that it gives the same frictional conditions at the tool-specimen interface. Experiments for two kinds of specimens are carried out in each testing equipment at room temperatue. From the experiments the deformed dimensions and the forging loads are measured and compared with each other by using the simulation coefficients. It is shown that there are good agreements between the model test and the prototype test. Finally, for verifying the availability of the model material technique this mathod is applied to forging of bevel gear product. the good result is obained which can demonstrate that the model material technique is very efficent for estimating or developing a new process.

• Proceedings of the KOSOMBE Conference
• /
• v.1994 no.12
• /
• pp.113-116
• /
• 1994

Estimation of the evoked potential using the iterated bispectrum and cross-correlation (IBC) has been tried for both simulation and real clinical data. Conventional time average (TA) method suffers from synchronization error when the latency time of the evoked potential is random, which results in poor SNR distortion in the estimation of EP waveform. Instead of EP signal average in time domain, bispectrum is used which is insensitive to time delay. The EP signal is recovered by the inverse transform of the Fourier amplitude and phase obtained from the bispectrum. The distribution of the latency time is calculated using cross-correlation between EP signal estimated by the bispectrum and the acquired signal. For the simulation. EEG noise was added to the known EP signal and the EP signal was estimated by both the conventional technique and bispectrum technique. The proposed bispectrum technique estimates EP signal more accurately than the conventional technique with respect to the maximum amplitude of a signal, full width at half maximum(FWHM). signal-to-noise-ratio, and the position of maximum peak. When applied to the real visual evoked potential(VEP) signal. bispectrum technique was able to estimate EP signal more distinctively. The distribution of the latency time may play an important role in medical diagonosis.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.834-837
• /
• 2005

Structural Dynamics Modification (SDM) is a very effective technique to improve structure's dynamic characteristics by adding or removing auxiliary structures, changing material properties and shape of structure. Among those of SDM technique, the method to change shape of structure has been mostly relied on engineer's experience and trial-and-error process which are very time consuming. In order to develop a systematic method to change structure shape, surface grooving technique is studied and successfully applied to HDD cover model. At first, to check the effect of mesh size, surface grooving technique was tested to the fine HDD cover FEmodel. And fur the more efficient method, the algorithm is modified. Removing the low-valued modal strain energy element among the target domain, computational effort can be greatly reduced and the result of simulation is similar with the other simulation result.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.331-334
• /
• 2003

In the finite element simulation of hot forging processes using hexahedron, remeshing of a flash is very difficult. The mesh compression method is a remeshing technique to construct an effective hexahedral mesh. However, because mesh is distorted during the compression procedure or the mesh compression method, mesh smoothing is necessary to improve the mesh Qualify. in this study, several geometric mesh smoothing techniques and a matrix norm optimization technique are applied and compared which is more adaptive to the mesh compression method.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.445-448
• /
• 1992

In this paper, we contructed extended Kalman filter for the image navigation systems. The conventional extended Kalman filter methode are simulated for nonlinear measurement systems. In addition, we designed a maneuvering target tracking filter using Singer's model technique and input estimation technique by Chan. Simulation results show that Chan's input estimation technique has performed better than Singer's technique.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.939-942
• /
• 2003

Design verification problem is emerging as an important issue to detect any design errors at the early stage of the design. Conventionally, design verifications have been done using a simulation technique. However, this technique has been proved not to cover all potential design errors. Therefore, formal technique is often used to verify digital circuits as an alternative. In this paper we adopted formal verification technique and verified some important properties derived from our pipelined digital systems, using SMV (Symbolic Model Verifier). Our example shows that model checking method (one of formal verification techniques) can be effectively performed in verifying the large digital systems.