• Smart Structures and Systems
• /
• 제15권3호
• /
• pp.627-643
• /
• 2015

Negative stiffness, previously emulated by active or semi-active control for cable vibration mitigation, is realized passively using a self-contained highly compressed spring, the negative stiffness device (NSD).The NSD installed in parallel with a viscous damper (VD) in the vicinity of cable anchorage, enables increment of damper deformation during cable vibrations and hence increases the attainable cable damping. Considering the small cable displacement at the damper location, even with the weakening device, the force provided by the NSD-VD assembly is approximately linear. Complex frequency analysis has thus been conducted to evaluate the damping effect of the assembly on the cable; the displacement-dependent negative stiffness is further accounted by numerical analysis, validating the accuracy of the linear approximation for practical ranges of cable and NSD configurations. The NSD is confirmed to be a practical and cost-effective solution to improve the modal damping of a cable provided by an external damper, especially for super-long cables where the damper location is particularly limited. Moreover, mathematically, a linear negative stiffness and viscous damping assembly has proven capability to represent active or semi-active control for simplified cable vibration analysis as reported in the literature, while in these studies only the assembly located near cable anchorage has been addressed. It is of considerable interest to understand the general characteristics of a cable with the assembly relieving the location restriction, since it is quite practical to have an active controller installed at arbitrary location along the cable span such as by hanging an active tuned mass damper. In this paper the cable frequency variations and damping evolutions with respect to the arbitrary assembly location are then evaluated and compared to those of a taut cable with a viscous damper at arbitrary location, and novel frequency shifts are observed. The characterized complex frequencies presented in this paper can be used for preliminary damping effect evaluation of an adaptive passive or semi-active or active device for cable vibration control.

• 지구물리와물리탐사
• /
• 제17권2호
• /
• pp.58-65
• /
• 2014

2012년 8월 4일 뉴질랜드 White Island 화산의 WIZ 관측소에서 기록된 화산성 장주기 지진파의 지진원 메커니즘에 대해 연구하였다. 하나의 관측소 자료만을 이용하였기 때문에 단순한 기하학적 모델(구, 균열, 파이프)들을 이용하여 모멘트 텐서 역산을 실시하였다. 각 모델의 합성자료를 계산하였으며, 이를 관측자료와 비교하였다. 가장 잘 일치하는 모델의 종류와 방향은 깊이 1600 m의 경사가 $80^{\circ}NE$이고 주향이 $N80^{\circ}W$인 균열 모델이었다. 깊은 곳에서의 폭발은 가스분출을 위한 균열을 열었으며, 상승한 가스가 약 4시간 후에 감시카메라에 포착된 지표 분화를 야기하였을 것으로 해석된다. 모멘트 텐서방법에 기초한 이러한 분석 결과는 이 화산섬을 대상으로 수행한 기존의 지화학 연구 결과와 일치한다.

• International Journal of Railway
• /
• 제2권3호
• /
• pp.118-123
• /
• 2009

Railway track alignment Standards set a minimum lenght value for straight and circular alignments (art. 5.2.9.), in order to ensure passenger ride comfort in railway vehicles of which dynamic oscillations will thus have to be limited. The transitions between alignments can cause abrupt changes (usually called discontinuities or singular points of the alignment) of curvature, of rate of change of curvature or of rate of change of cant. A passenger is likely to experience effects due to the excitation of the elastic suspension of the vehicle which generates oscillations that are damped as the vehicle moves away from the singularity. The amplitude of these oscillations should be adequately attenuated by the damping of the suspension system within the interval between two successive singular points, especially to avoid resonances. Therefore minimum lengths between two successive singular points are stated in alignment standards. Nevertheless, these nonnative values can be overly conservative in some cases. As an alternative, track alignment designers could try to assess how much the excitation has been attenuated between two successive singular points and thus assess at which point a new singularity may be present without affecting ride comfort. Although such assessment can be made with commercial SW packages which simulate the dynamic behavior of a vehicle considered as a set of rigid bodies interconnected with elastic elements simulating the suspension systems (such as SIMPACK, ADAMS or VAMPIRE), a simplified and user-friendly computation method (based upon the analytical solution of differential equations governing the phenomenon) is made available in this paper to track design engineers, not always used to working with full dynamic models.

• KSBB Journal
• /
• 제16권2호
• /
• pp.146-152
• /
• 2001

rhGH-GST 융합단백질을 사용하여 재조합 대장균 세포 파쇄액으로부터 직접적으로 내포체의 solid-phase 재접힘을 수행할 수 있는 새로운 공정을 개발하였다. 그것은 고체 업자를 제거하는 동시에 초기에 목적딴백질을 흡착 포집할 수 있 는 expanded bed adsorption 크로마토그래피의 장점을 이용한 것이다. 세포 파쇄액 내 용해훤 내포체로부터의 풀린 융합단백질은 expanded bed adsorption 원리에 의해 STREAMLINE DEAE resin에 흡착되고 세포 찌꺼기 등 고체 입자물들은 위 방향 흐름에 의해 효과적으로 제거된다. Urea를 접차적으로 제거함으로써 융합단백질은 고체 matrix 표면에서 재접힘 된 후 염 놓도 구배에 의해 용출된다. 이 새로운 EBA-mediat$\xi$d 재접힘 방법은 응집현상을 획기적으로 줄이고 공정수율윤 향상시킬 뿐 아나라 공정단계 수를 줄일 수 있다. 이 공정은 우리가 알고 있는 한 세계에서 최초로 개발된 공정이며, 현재 single-chain polypeptide, affinity-tagged protein 등과 갈은 다른 행태의 단백질에 EBA를 사용한 재접힘 공정올 적용시키가 위한 연구가 진행되고 있다.

• International Journal of Fluid Machinery and Systems
• /
• 제3권4호
• /
• pp.315-323
• /
• 2010

This work investigates the influence of water compressibility on pressure pulsations induced by rotor-stator interaction (RSI) in hydraulic machinery, using the commercial CFD solver ANSYS-CFX. A pipe flow example with harmonic velocity excitation at the inlet plane is simulated using different grid densities and time step sizes. Results are compared with a validated code for hydraulic networks (SIMSEN). Subsequently, the solution procedure is applied to a simplified 2.5-dimensional pump-turbine configuration in prototype with different speeds of sound as well as in model scale with an adapted speed of sound. Pressure fluctuations are compared with numerical and experimental data based on prototype scale. The good agreement indicates that the scaling of acoustic effects with an adapted speed of sound works well. With respect to pressure fluctuation amplitudes along the centerline of runner channels, incompressible solutions exhibit a linear decrease while compressible solutions exhibit sinusoidal distributions with maximum values at half the channel length, coinciding with analytical solutions of one-dimensional acoustics. Furthermore, in compressible simulation the amplification of pressure fluctuations is observed from the inlet of stay vane channels to the spiral case wall. Finally, the procedure is applied to a three-dimensional pump configuration in model scale with adapted speed of sound. Normalized Pressure fluctuations are compared with results from prototype measurements. Compared to incompressible computations, compressible simulations provide similar pressure fluctuations in vaneless space, but pressure fluctuations in spiral case and penstock may be much higher.

• Korean Chemical Engineering Research
• /
• 제56권1호
• /
• pp.29-41
• /
• 2018

공비점이 존재하거나 상대휘발도 차이가 적은 2성분 혼합물은 단일 증류탑으로 분리하기 어렵다. 이때 혼합물에서 분리가 어려운 영역을 투과증발막을 사용하여 분리하면 효율적인 공정을 설계할 수 있다. 본 연구에서는 물-유기용매 혼합물을 분리하기 위한 증류-투과증발막 혼성공정을 제시하고, 물-초산 혼합물과 물-에탄올 혼합물의 분리공정을 각각 모사하였다. 증류탑 상부 흐름이 친수성 막을 통과하여 물을 높은 순도로 분리하는 공정을 모사하였다. 실험과 문헌에서 얻은 친수성 막의 투과도를 토대로 막 모델을 만들어 막 면적을 계산하였다. 제시한 공정의 최적화를 위해, 목적함수를 연간 총 비용으로 정하고 주요 설계 변수들을 최적화 변수로 하여 최적화 문제를 구성하였다. 또한, 혼성공정의 각 최적화 변수의 변화에 따른 목적함수 값의 변화 추세를 나타내고 최적화 변수를 최적점에 가까운 값으로 쉽게 추측할 수 있는 방법을 제안하였다.

• KIEAE Journal
• /
• 제16권4호
• /
• pp.71-77
• /
• 2016

Purpose : The energy saving in a residential building (apartment) sector is known as one of the effective solution of energy reduction. In South Korea, the government has recently reinforced regulations associated with the energy performance of buildings. However, there is a lack of research on the methods for the energy performance diagnosis that is used to analyze the wall thermal performance of the existing apartments. Because a reliable diagnosis is necessary to save the building energy, this study analyzed wall thermal performance of an existing apartment in Seoul. Method : This paper applied two methods for analysis of the thermal insulation performance; HFM(Heat Flow Meter) method and ASTR(Air-Surface Temperature Ratio) method. The HFM method is suggested by ISO9869-1 code to measure the thermal performance. The ASTR method is proposed by this study for the simplified In-situ measurement and it uses three temperature data (interior wall surface, interior and exterior air) and the overall heat transfer coefficient. This study conducted the experiment of an existing apartment in Seoul using these methods and analyzed the results. Furthermore, the energy simulation tool of the building was used to suggest retrofit of the building based on the results of measurements. Result : The error rate of HFM method and ASTR method was analyzed in about 17 to 20%. As the results of comparison between the initial design values of the wall and the measured values, the 26% degradation of insulation thermal performance was measured. Lastly, the energy simulation tool of the building shows 10.8% energy savings in accordance with the construction of suggested retrofit.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.1
• /
• pp.535-540
• /
• 2006

The relationship between the observable noise model and the satellite elevation angle can be modeled quite well by an exponential function.[Jin, 1996] Noise size and dependence on the elevation angle are, however, different for each observation and receiver type. Therefore, the coefficient determination of this model is an issue, and various methods including PR-CP, single difference, and time difference have been suggested. The limitations of them are difficulty to model the carrier phase noise and to eliminate bias. To overcome these disadvantages for using Jin's model, we suggest zero baseline double difference (DD) and noise sorting algorithm. Data DD technique in zero baseline is useful to eliminate all the troublesome GPS biases, and the remaining error is the sum of GPS measurement noises from two satellites. These DD residuals for hours should be sorted by the combination of satellite elevation angles, and then variance value of the residual for each combination can be estimated. Using these values, we construct an over-determined linear equation whose solution is a set of noise variance for each satellite elevation angle. With 24hr Trimble 4000ssi data, we easily worked out the coefficients of the noise model not only for pseudorange but also for carrier phase. We estimated the standard deviation of the measurement DD using our model, and plotted 1 and 3 sigma lines for every epoch to verify the representation of the residual error. 63.3% of pseudorange residual and 65.9% of phase error did not exceed the 1 sigma lines. Additionally, 99.2% and 99.5% of them lied within 3sigma line. These figures prove that the Gaussian property of measurement noise, and that the suggested model by our algorithm corresponds to the observable noise information.

• KIEE International Transactions on Power Engineering
• /
• 제5A권1호
• /
• pp.85-92
• /
• 2005

In this paper, Nash equilibriums of generation markets are investigated using a game theory application for simplified competitive electricity markets. We analyze the characteristics of equilibrium states in N-company spot markets modeled by uniform pricing auctions and propose a new method for obtaining Nash equilibriums of the auction. We assume that spot markets are operated as uniform pricing auctions and that each generation company submits its bids into the auction in the form of a seal-bid. Depending on the bids of generation companies, market demands are allocated to each company accordingly. The uniform pricing auction in this analysis can be formulated as a non-cooperative and static game in which generation companies correspond to players of the game. The coefficient of the bidding function of company-n is the strategy of player-n (company-n) and the payoff of player-n is defined as its profit from the uniform price auction. The solution of this game can be obtained using the concept of the non-cooperative equilibrium originating from the Nash idea. Based on the so called residual demand curve, we can derive the best response function of each generation company in the uniform pricing auction with N companies, analytically. Finally, we present an efficient means to obtain all the possible equilibrium set pairs and to examine their feasibilities as Nash equilibriums. A simple numerical example with three generation companies is demonstrated to illustrate the basic idea of the proposed methodology. From this, we can see the applicability of the proposed method to the real-world problem, even though further future analysis is required.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.73-86
• /
• 1995

The automatic control system in the greenhouse have to be developed to the direction of considering various factors the variables such as condition of the cultivation and greenhouse, the properties and types of products. Therefore, it is more important to set up variables appropriately than the problems of automatic control system itself, and the automatic control system which satisfy these problems should be simplified in the aspect of operation. In addition, even the individual automations are not perfect yet, so more studies are required for the development of comprehensive automatic system in korea. This study was carried out to automatize environment control systems for greenhouse, especially from most intensive labor requiring parts such as watering, irrigating liquefied fertilizer, spraying chemicals, mixing and ventilation system, etc. The results are summarized as follows. 1. Control type tensiometer was expected to be desirable in the automation of watering system, therefore, a new tensiometer was designed and developed through this study. 2. The chemical spraying system developed through this study was found to be excellent in the aspect of operation. 3. When pulse type water discharge meter was used in the mixing of liquefied fertilizer and chemical solution, the error of mixing were range $\pm$0.1~0.15%. 4. The water level switch of electrod type used for controlling water level was found to be affective in both control performance and operation cost. 5. The water and level control system can be omitted if each tank size are standardized in accordance with greenhouse size, therefore, the installation cost might be significantly reduced. 6. The developed general controller was excellent in hardware parts, but still remained to be improved in software parts.