• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.2
• /
• pp.138-143
• /
• 2004

This experimental paper deals with the performance of tanks that are turned the active A.R.T(Anti-Rolling Tank) when the fluid transfers from wing tank to the opposite tank by the power developed by the automatic control system (INTERING Stabilizer), which was installed in the fishery training ship T/S. A - RA (G/T:990 tons) of Cheju National University. In this paper, the author has tested the performance of INTERING Stabilizer for the signals obtained by the inclinometer in irregular waves and compared with the results obtained in passive mode operation at stop and at various ship speeds. The performances of the system were confirmed the results as follows through the tests: 1. The average amplitude and significant roll (${\pi}$1/3) of the passive and active mode operations in the condition of stoped engine and underway were obtained 8.30$^{\circ}$, 4.37$^{\circ}$, 8.30$^{\circ}$, 4.37$^{\circ}$, and 5.01$^{\circ}$, 4.36$^{\circ}$, 5.50$^{\circ}$, 5.10$^{\circ}$, respectively. 2. The rates of performance of active mode operations were carried out during a sea trial in the condition of stop engine and underway resulted in 47.5%, 12.7%, respectively, therefore the active mode operation estimated to be improved more than passive mode operation. 3. Active - A.R.T by INTERING Stabilizer didn't affect the amplitude of pitching.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2877-2883
• /
• 2010

The folding kinetics of $WT^*$ ubiquitin variant with valine to alanine mutation at sequence position 26 (HubWA) was studied by stopped-flow fluorescence spectroscopy. While unfolding kinetics showed a single exponential phase, refolding reaction showed three exponential phases. The semi-logarithmic plot of urea concentration vs. rate constant for the first phase showed v-shape pattern while the second phase showed v-shape with roll-over effect at low urea concentration. The rate constant and the amplitude of the third phase were constant throughout the urea concentrations, suggesting that this phase represents parallel process due to the configurational isomerization. Interestingly, the first and second phases appeared to be coupled since the amplitude of the second phase increased at the expense of the amplitude of the first phase in increasing urea concentrations. This observation together with the roll-over effect in the second folding phase indicates the presence of intermediate state during the folding reaction of HubWA. Quantitative analysis of Hub-WA folding kinetics indicated that this intermediate state is on the folding pathway. Folding kinetics measurement of a mutant HubWA with hydrophobic core residue mutation, Val to Ala at residue position 17, suggested that the intermediate state has significant amount of native interactions, supporting the interpretation that the intermediate is on the folding pathway. It is considered that HubWA is a useful model protein to study the contribution of residues to protein folding process using folding kinetics measurements in conjunction with protein engineering.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.2
• /
• pp.148-156
• /
• 2008

In this study it will be discussed how to solve the problem of discomfort from rolling motion on the fishing boats. Most discomfort is caused by the short cycle of rolling due to the light weight of the boats. The light weight is due to the FRP material which dries a boat. A way to improve the feeling of boarding by using fish hold was researched. The experiment was done on experimental fishing boat made by FRP in Jeju. An existing fish hold was designed and manufactured through the rolling test and that was used for a marine experiment. The rolling condition of the U-tank boat ideally designed was compared to that of an existing fishing boat using the same conditions. The experiments were carried out two times on the stop engine in the outward Sehwa fishing port, which the experimental data had analysed for effects of rolling reduction to compare the U - tank with the of exiting fish hold. The results were confirmed that the U-boat tank in the roll period and GoM were more safe than the existing fish hold and the average amplitude and significant of rolling angles were decreased relatively.

• Journal of Navigation and Port Research
• /
• v.42 no.2
• /
• pp.127-136
• /
• 2018

The motion response of floating structures is of significant concern in marine engineering. Floating structures can be disturbed by waves, winds, and currents that create undesirable motions of the vessel, therefore causing challenges to its operation. For a floating structure, mooring lines are provided in order to maintain its position; these should also produce a restoring force when the vessel is displaced. Therefore, it is important to investigate the tension of mooring lines and the motion responses of a twin barge when moored to guarantee the safety of the barge during its operation. It is essential to precisely identify the characteristics of the motion responses of a moored barge under different loading conditions. In this study, the motion responses of a moored twin barge were measured in regular waves of seven different wave directions. The experiment was performed with regular waves with different wavelengths and wave directions in order to estimate the twin-barge motions and the tension of the mooring line. In addition, the motion components of roll, pitch, and heave are completely free. In contrast, the surge, sway, and yaw components are fixed. In the succeeding step, a time-domain analysis is carried out in order to obtain the responses of the structure when moored. As a result, the Response Amplitude Operator (RAO) motion value was estimated for different wave directions. The results of the experiment show that the motion components of the twin barge have a significant effect on the tension of the mooring lines.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.6_1
• /
• pp.907-915
• /
• 2020

Specification selection, Layout, specifications and combinations of Power Drives, and Ship motions were studied for FGPP(Floating Gas-fired Power Plants), which are still needed in areas such as the Caribbean, Latin America, and Southeast Asia where electricity is not sufficiently supplied. From this study, the optimal equipment layout in ships was derived. In addition, the difference between engine and turbine was verified through LCOE(Levelized Cost of Energy) comparison according to the type and combination of Power Drives. Analysis of Hs(Significant Height of wave) and Tp(spectrum Peak Period of wave) for places where this FGPP will be tested or applied enables design according to wave characteristics in Brazil and Indonesia. Normalized Sloshing Pressures of FGPP and LNG Carrier are verified using a sloshing analysis program, which is CFD(Computational Fluid Dynamics) software developed by ABS(American Bureau of Shipping). Power Transmission System is studied with Double bus with one Circuit Breaker Topology. A nd the CFD analysis allowed us to calculate linear roll damping coefficients for more accurate full load conditions and ballast conditions. Through RAO(Response Amplitude Operator) analysis, we secured data that could minimize the movement of ships according to the direction of waves and ship placement by identifying the characteristics of large movements in the beam sea conditions. The FGPP has been granted an AIP(Approval in Principle) from a classification society, the ABS.

• Wind and Structures
• /
• v.23 no.2
• /
• pp.127-142
• /
• 2016

Aerodynamic effects, such as drag force and flow-induced vibration (FIV), on civil engineering structures can be minimized by optimally modifying the structure shape. This work investigates the turbulent wake of a square prism with its faces modified into a sinusoidal wave along the spanwise direction using three-dimensional large eddy simulation (LES) and particle image velocimetry (PIV) techniques at Reynolds number $Re_{Dm}$ = 16,500-22,000, based on the nominal width ($D_m$) of the prism and free-stream velocity ($U_{\infty}$). Two arrangements are considered: (i) the top and bottom faces of the prism are shaped into the sinusoidal waves (termed as WSP-A), and (ii) the front and rear faces are modified into the sinusoidal waves (WSP-B). The sinusoidal waves have a wavelength of $6D_m$ and an amplitude of $0.15D_m$. It has been found that the wavy faces lead to more three-dimensional free shear layers in the near wake than the flat faces (smooth square prism). As a result, the roll-up of shear layers is postponed. Furthermore, the near-wake vortical structures exhibit dominant periodic variations along the spanwise direction; the minimum (i.e., saddle) and maximum (i.e., node) cross-sections of the modified prisms have narrow and wide wakes, respectively. The wake recirculation bubble of the modified prism is wider and longer, compared with its smooth counterpart, thus resulting in a significant drag reduction and fluctuating lift suppression (up to 8.7% and 78.2%, respectively, for the case of WSP-A). Multiple dominant frequencies of vortex shedding, which are distinct from that of the smooth prism, are detected in the near wake of the wavy prisms. The present study may shed light on the understanding of the underlying physical mechanisms of FIV control, in terms of passive modification of the bluff-body shape.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.2
• /
• pp.200-206
• /
• 2013

The paper was investigated on the mooring forces(or tension) and motion response characteristics for a 8-point mooring floating dock in regular waves using a commercial code(AQWA). To achieve the aim of the research, a numerical simulation was adapted on an inner port environment condition, which the water depth is 10 meters, significant wave amplitude(1.05 m). wave period(3.85 sec), wind speed(20.21 m/s), wind and current direction ($90^{\circ}$), incident waves(${\chi}=180^{\circ}$, $135^{\circ}$ and $90^{\circ}$). The dimension of the numerical model is length(140 m), breadth(32 m), depth(14.6 m). The maximum length of a mooring line is 120m. We can expected that roll and pitch motions appeared in beam seas better than head sea. the mooring forces also indicated higher in bean seas than in head seas including wind forces.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.889-901
• /
• 2021

The tension of cables and motion response significantly affect safety of an immersed tunnel element in the immersion process. To investigate those, a hydrodynamic scale-model test was carried out and the model experiments was conducted under wind, current and wave loads simultaneously. The immersion standby (the process that the position of the immersed tunnel element should be located before the immersion process) and immersion process conditions have been conducted and illustrated. At the immersion standby conditions, the maximum force of the cables and motion is much larger at the side of incoming wind, wave and current, the maximum force of Element-6 (6 cables directly tie on the element) is larger than for Pontoon-8 (8 cables tie on pontoon of the element), and the flexible connection can reduce the maximum force of the mooring cables and motion of element (i.e. sway is expecting to decrease approximate 40%). The maximum force of the mooring cables increases with the increase of current speed, wave height, and water depth. The motion of immersed tunnel element increases with increase of wave height and water depth, and the current speed had little effect on it. At the immersion process condition, the maximum force of the cables decrease with the increase of immersion depth, and dramatically increase with the increase of wave height (i.e. the tension of cable F4 of pontoons at wave height of 1.5 m (83.3t) is approximately four times that at wave height of 0.8 m). The current speed has no much effect on the maximum force of the cables. The weight has little effect on the maximum force of the mooring cables, and the maximum force of hoisting cables increase with the increase of weight. The maximum value of six-freedom motion amplitude of the immersed tunnel element decreases with the increase of immersion depth, increase with the increase of current speed and wave height (i.e. the roll motion at wave height of 1.5 m is two times that at wave height of 0.8 m). The weight has little effect on the maximum motion amplitude of the immersed tunnel element. The results are significant for the immersion safety of element in engineering practical construction process.

• Journal of Biomedical Engineering Research
• /
• v.34 no.3
• /
• pp.129-134
• /
• 2013

The essential tremor is an involuntary oscillatory movement of body parts. Conventional treatments of essential tremor have little effects in some patients and also leads to significant side effects. Alternative to these treatments, sensory stimulation may have beneficial effects on the essential tremor. The purpose of this study was to analyze an effect of sensory stimulation on essential tremor. Ten patients with essential tremor ($67.4{\pm}8.82$ yrs, 5 men and 5 women) participated in this study. Three-axis gyro sensors were attached on index finger, hand and forearm of patients. Task of 'arms outstretched forward' was performed with and without sensory stimulation. Vectorsum of three dimensional angular velocities (pitch, roll, yaw) was calculated. Outcome measures included root-meansquare (RMS) mean of the vector-sum amplitude, total power, peak power and peak frequency. RMS amplitude, total power and peak power were reduced by sensory stimulation (p < 0.05). Peak frequency was not affected by sensory stimulation. The results indicate that the sensory stimulation is useful to suppress the essential tremor.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.7
• /
• pp.904-914
• /
• 2020

Through the Ministry of Trade, Industry, and Energy, South Korea is trying to support the "Building Project for Liquified Natural Gas (LNG) Bunkering Ship," centered on the Korea Gas Corporation, while the Ministry of Maritime Af airs and Fisheries is pushing to construct an LNG bunkering terminal at Busan New Port. LNG bunkering ships are essential for supplying LNG fuel from the terminal to the ships, resulting in the need for safety operation procedures. Therefore, in this study, the stability of a coastal LNG bunkering ship operating from Busan New Port to the anchorage in Busan Port was assessed to investigate the need for operational procedures for coastal LNG bunkering ships. Seakeeping analysis of the LNG bunkering ship was performed for each significant wave height by combining the response amplitude operator from the ship motion analysis under the potential flow theory with the actual observed sea data for five years and Texel, Marsen, and Arsloe (TMA) spectrum suitable for the Busan coast. The results showed that the roll and horizontal acceleration were the main risks that affected the navigation seakeeping performance above a significance wave height of 2 m. The operational periods of the LNG bunkering ship ranged from 83.3% to 99.9% of the total observation period.