• 재활복지공학회논문지
• /
• 제11권1호
• /
• pp.63-71
• /
• 2017

본 논문에서는 달팽이관의 정원창 이식용으로 최근 새롭게 제안된 3코일 벨로우즈형 진동체(tri-coil bellows transducer, TCBT)를 이용하는 반이식형 인공중이(semi-implantable middle ear hearing device)를 위한 신호처리회로를 설계하였다. 설계된 반이식형 인공중이는 높은 효율을 가지는 유도결합 방법을 이용하여 귀 뒤편에 착용되는 체외기와 대응되는 피부 내측에 위치하는 체내기 간에 데이터를 전송한다. 귀 뒤 부위의 피부두께를 포함하는 반이식형 인공중이의 송수신 거리를 고려하여 송수신 코일과 신호처리 회로를 설계 및 구현하였다. 또한 데이터 전송 효율을 높이기 위하여, 전력을 충분히 증폭하기 위한 체외기의 출력부도 설계 하였다. 유도결합 방식을 이용한 반이식형 인공중이의 동작을 확인하기 위하여, PSpice를 이용하여 회로해석을 수행하였으며, 활용 가능한 크기의 신호처리 보드를 제작하여 그 성능을 검증하였다.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권6호
• /
• pp.291-297
• /
• 2003

This paper presents a current-source-inverter based on a buck-boost configuration and its application for residential photovoltaic system. The proposed circuit has five switches. Among them, only one switch acts as chopping, and the other determine the polarity of output; therefore, it can reduce the switching loss. Because the input inductor current is operated on the discontinuous conduction mode, high power factor can be achieved without additional input current controller. So the overall system shows a simple structure. The operational modes are analysed in depth, and then it was verified through the experimental results using a 150 [W] prototype equipped with digital signal processor TMS320F241.

• ETRI Journal
• /
• 제26권6호
• /
• pp.513-519
• /
• 2004

This paper presents a low power 16-bit adiabatic reduced instruction set computer (RISC) microprocessor with efficient charge recovery logic (ECRL) registers. The processor consists of registers, a control block, a register file, a program counter, and an arithmetic and logical unit (ALU). Adiabatic circuits based on ECRL are designed using a $0.35{\mu}m$ CMOS technology. An adiabatic latch based on ECRL is proposed for signal interfaces for the first time, and an efficient four-phase supply clock generator is designed to provide power for the adiabatic processor. A static CMOS processor with the same architecture is designed to compare the energy consumption of adiabatic and non-adiabatic microprocessors. Simulation results show that the power consumption of the adiabatic microprocessor is about 1/3 compared to that of the static CMOS microprocessor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1071-1074
• /
• 2002

In this paper, power quality analysis system is proposed where voltage or current waveforms are nonsinusoidal. The proposed system relies on the FFT algorithm to compute real and reactive power. The advantage of system is that harmonic analysis is carried out on a period of the input signal. The proposed system is based on FFT processor which is designed using VHDL(Very high-speed integrated circuit Hardware Description Language). In the design of FFT processor, radix- $2^2$ is adopted to reduce several complex multipliers for twiddle factor. Complex multiplier is implemented as only shifters and adders. Therefore, the system is able to have both high hardware efficiency and high performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.113.3-113
• /
• 2001

In this paper, we have designed the VHDL module of DS/SS QPSK wireless modem processor for digital data communication. The spread spectrum method is used for modern processor, because this method guarantees good frequency efficiency and higher security. Also, it guarantees good performance in digital communication system under multi-path interferences. The differential encoder and decoder are used for simple circuit composition in the signal detection. For the synchronization of receiver, matched filter and power detector are used. And the IF modulation/demodulation of QPSK method is used in the digital level. The transmitter of VHDL modem processor consists of differential encoder, PN code generator, and QPSK ...

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권7호
• /
• pp.317-322
• /
• 2002

This paper presents a linear temperature/voltage relation over a temperature range(0~100$^{\circ}C$) with high-resolution, reasonably god response linearity, reliability, and overall improved performance. A notable feature of the proposed method is that the whole temperature span is divided by 16 subbands thus the variation span of measured voltage is narrowed. Therefore noise characteristic has been improved. The output voltage is amplified after the uniformed DC voltage component is eliminated by offset. We proposed circuit using median value and mean value of digital signal in order to reduce the noise effect. The proposed circuit offers linear temperature/voltage conversion over a wide dynamic range using DSP(TMS320C31) and steinhart equation.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.68.2-68
• /
• 2002

The purpose of this paper is to monitor ECU's self-diagnostic signal without wire. In order to measure the ECU's self-diagnostic signal, the interfaced circuit is developed to communicate ECU with a designed display terminal according to the ISO, SAE regulation of communication protocol standard. An 80C196KC processor is used for communicating ECU's self-diagnostic signal and communication data are sent to PDA monitoring system that is based on the Windows CE. Software on PDA is developed to monitor the ECU's self-diagnostic signal in which RS232 port is programmed by half duplex method. The algorithms for measuring the ECU's self-diagnostic signals are verified to mo...

• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.40-48
• /
• 2015

In this paper, battery charging and discharging circuit with a single voltage power supply is proposed. The proposed circuit has the separated current path and charging-monitoring sequence control scheme. In the charging sequence, the proposed 2-level comparator combined with control signal of the micro-processor can control the constant charging current to protect the over current of the battery. Furthermore, the proposed circuit uses a periodic main power switch control to detect the discharging characteristics to estimate the approximated battery life-time. In the experiments, the proposed emergency power supply for emergency call system has 89% efficiency with 98% power factor. And the proposed sequence control scheme is well operated in the designed emergency power system.

• ETRI Journal
• /
• 제10권2호
• /
• pp.32-39
• /
• 1988

In this paper, we describe an effective trunk loop signal processing method and anlayze execution time of the program in the DTCP (Digital Trunk Circuit Processor) in the TDX-1A digital switching stytem. And we also predict a maximum trunk capacity in the DTCP with respect to scanning period based on the call attempt characteristics which has the Poisson distribution.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.654-657
• /
• 1998

This paper is described a digital implementation of a pulse area modulation (PAM) method for a unity-power-factor buck-boost converter. A digital controller is designed and implemented by a Digital Signal Processor(DSP) to replace the analog control circuit for PAM. Experimental results are presented and compared with simulations.