• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.2
• /
• pp.86-88
• /
• 2002

An estimation method for the characteristic parameters in the low frequency signal is proposed in this paper. A low frequency signal is assumed to be modulated or distorted by high frequency terms. The algorithm proposed in this paper is designed to select set of local maximums in a successive manner, hence it is denoted as the iterative peak picking(IPP) algorithm. The IPP algorithm is operating in the time domain and is using only the comparison operation between two neighboring samples. Therefore, its computational complexity is very low and the delay caused by the computation is negligible, which make the real-time operation possible with economic hardware. The proposed algorithm is verified on the pitch estimation of speech signal and blood pulse estimation.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.247-251
• /
• 2003

The velocity of train which is measured from pulse generator attached to TM is used for displaying or control signal of inverter and so on. Measured signals increase and decrease step-by-step by pulse counting or monotonously by F/V conversion. But noises and signal distortions by measuring error like alias make it difficult to provide correct velocity infomation and estimate the acceleration. In this paper, we investigated the performance of Smoothing method for suppressing the noises in velocity signals. And the difference between Smoothed signal and origin velocity signals is inspected and the comparison with low pass filtering show applicable of Smoothing method for noise rejection and the estimation of signal. Finally, acceleration curves estimated from Smoothing method are compared with real accelerator signal attached to train.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.7
• /
• pp.646-652
• /
• 2013

EU's Galileo project is a market-based GNSS (Global Navigation Satellite System) that is under development. It is expected that Galileo will provide the positioning services based on new technologies in 2020s. Because Galileo E1 signal for OS (Open Service) shares the same center frequency with GPS L1 C/A signal, CBOC (Composite Binary Offset Carrier) modulation scheme is used in the E1 signal to guarantee interoperability between two systems. With E1 signal consisting of a data channel and a pilot channel at the same frequency band, there exist several options in designing signal acquisition for Assisted-Galileo receivers. Furthermore, compared to SNR worksheet of Assisted-GPS, some factors should be examined in Assisted-Galileo due to different correlation profile and code length of E1 signal. This paper presents SNR worksheets of Galileo E1 signals in E1-B and E1-C channel. Three implementation losses that are quite different from GPS are mainly analyzed in establishing SNR worksheets. In the worksheet, hybrid long integration of 1.5s is considered to acquire weak signal less than -150dBm. Simulation results show that the final SNR of E1-B signal with -150dBm is 19.4dB and that of E1-C signal is 25.2dB. Comparison of relative computation shows that E1-B channel is more profitable to acquire the strongest signal in weak signal environment. With information from the first satellite signal acquisition, fast acquisition of the weak signal around -155dBm can be performed with E1-C signal in the subsequent satellites.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.1
• /
• pp.39-45
• /
• 2011

In this paper, the design method of portable signal analysis system is proposed and the hardware module is implemented for operation of base stations based on a common platform for mobile WiMax. The new signal analysis method is implemented as two modules; a broadband RF module and a DSP based digital signal analysis module. The RF module performs the RF-IF down conversion and gain control. And the digital module measure the base staion signal. The differences of performance are insignificant in the experiment results performed through the comparison of other fixed-large system and proposed system.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.1
• /
• pp.1-8
• /
• 2017

In this study, to design a multi-GNSS receiver using single RF front-end, the receiving performances for various frequency plans were evaluated. For the fair evaluation and comparison of different frequency plans, the same signal needs to be received at the same time. For this purpose, two synchronized RF front-ends were configured using USRP X310, and PC-based software was implemented so that the quality of the digital IF signal received at each front-end could be evaluated. The software consisted of USRP control, signal reception, signal acquisition, signal tracking, and C/N0 estimation function. Using the implemented software and USRP-based hardware, the signal receiving performances for various frequency plans, such as the signal attenuation status, overlapping of different systems, and the use of imaginary or real signal, were evaluated based on the C/N0 value. The results of the receiving performance measurement for the various frequency plans suggested in this study would be useful reference data for the design of a multi-GNSS receiver in the future.

• Journal of Korean Society of Transportation
• /
• v.20 no.5
• /
• pp.193-206
• /
• 2002

A signal optimization model is proposed by applying the Cell-Transmission Model(CTM) as an embedded traffic flow model to estimate a system-optimal signal timing plan in a transportation network composed of signalized intersections. Beyond the existing signal-optimization models, the CTM provides appropriate theoretical and practical backgrounds to simulate oversaturation phenomena such as shockwave, queue length, and spillback. The model is formulated on the Mixed-Integer Programming(MIP) theory. The proposed model implies a system-optimal in a sense that traffic demand and signal system cooperate to minimize the traffic network cost: the demand departing from origins through route choice behavior until arriving at destinations and the signal system by calculating optimal signal timings considering the movement of these demand. The potential of model's practical application is demonstrated through a comparison study of two signal control strategies: optimal and fixed signal controls.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.12-18
• /
• 2000

This paper describes the analysis of ultrasonic signal and partial discharge(PD) signal patterns for each location of particle in GIS. The characteristics of the ultrasonic signal and PD signal patterns for each location were as follows; in case of particle on the electrode, large ultrasonic signals and large PD signals occurred in positive half-cycle periodically; in case of particle on the spacer, ultrasonic signals and large PD signals occurred in negative half-cycle periodically; in case of the free moving particle, ultrasonic signals and large PD signals occurred by collision non-periodically. As a result, it was confirmed that particle in GIS could be located by the comparison and analysis of ultrasonic signal and PD signal patterns.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.43-52
• /
• 2014

P-wave characteristic in the human electrocardiogram (ECG) is important in the diagnosis of atrial conduction pathology. In this paper, we measured an ECG signal from patient with cardiovascular disease using one lead ECG electrode system which is based on the wireless cardiac monitoring system. And we detected a P-wave in ECG signal using the complex-valued continuous wavelet transforms (CWT) according to two kinds of patch type electrodes such as an existing narrow patch type electrode and the improved wide patch type electrode presented in this paper. Also, we compared the characteristics in detecting the P-wave in terms of the magnitude and the width of P-waves. From the results of comparison we found that the width and the magnitude of P-wave detected using the wide patch type electrode is improved to be interpreted easier compared to those using the narrow patch type electrode. Furthermore, we have also proven that the complex-valued CWT can be used as a robust detector for P-wave in ECG signal analysis.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.11 no.2
• /
• pp.178-183
• /
• 2001

Welding is essential for the manufacture of a range of engineering components which may vary from very large structures such as ships and bridges to very complex structures such as aircraft engines, or miniature components for microelectronic applications. Especially, a domestic situation of the welding automation is still depend on the arc sensing system in comparison to the vision sensing system. Specially, the gap-detecting of workpiece using conventional arc sensor is proposed in this study. As a same principle, a welding current varies with the size of a welding gap. This study introduce to the fuzzy membership filter to cancel a high frequency noise of welding current, and ART2 which has the competitive learning network classifies the signal patterns the filtered welding signal. A welding current possesses a specific pattern according to the existence or the size of a welding gap. These specific patterns result in different classification in comparison with an occasion for no welding gap. The patterns in each case of 1mm, 2mm, 3mm and no welding gap are identified by the artificial neural network.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.12
• /
• pp.1260-1268
• /
• 2009

Three methods(the stepped sine method, the statistical method(random excitation method) and the maximum-length sequence(MLS) method) for head-related transfer functions(HRTFs) are experimentally compared in view point of accuracy and efficiency. First, the stepped sine method has high signal-to-noise ratio, but low efficiency. Second, the statistical method is fast measurement speed, but weak to noise than the other methods. Finally, the MLS method shows both good efficiency and high signal-to-noise ratio, but it needs additional software or equipment such as MLS signal generator. For comparison of measurement accuracy, HRTFs of KEMAR dummy are measured for various azimuths and elevations. Error norms for magnitude and phase of HRTFs are defined and calculated for the measured HRTFs. The calculated error norms show that the methods give similar results in magnitude and phase except a little phase difference in the MLS method.