• Steel and Composite Structures
• /
• 제19권1호
• /
• pp.93-110
• /
• 2015

The thermomechanical bending response of anti-symmetric cross-ply composite plates is investigated by the use of the simple four variable sinusoidal plate theory. The theory accounts for sinusoidal distribution of transverse shear stress, and satisfies the free transverse shear stress conditions on the top and bottom surfaces of the plate without using shear correction factor. By dividing the transverse displacement into bending and shear parts, the number of unknowns and governing equations for the present theory is reduced, significantly facilitating engineering analysis. The validity of the present theory is demonstrated by comparison with solutions available in the literature. Numerical results are presented to demonstrate the behavior of the system. The influences of aspect ratio, side-to-thickness ratio, thermal expansion coefficients ratio and stacking sequence on the thermally induced response are studied. The present study is relevant to aerospace, chemical process and nuclear engineering structures which may be subjected to intense thermal loads.

• 한국전산구조공학회논문집
• /
• 제28권5호
• /
• pp.553-561
• /
• 2015

지수 함수 및 멱 법칙 함수를 이용한 점진기능재료(FGM) 판의 전단 및 두께 방향 변형을 고려한 이론을 정식화하여 동적 평형방정식을 유도하였다. 지수 함수 및 멱 법칙 함수는 두께 방향으로 재료의 변화를 고려할 수 있고 3차원 해석방법은 전단 및 두께 방향 변형을 고려함으로써 점진기능재료의 정확한 구조적 특성을 고려할 수 있다. Pasternak탄성지반 위에 놓인 4변이 단순 지지되고 전단 및 두께 방향 변형이 고려된 점진기능재료 판의 지배방정식을 풀기 위해 Navier 방법을 사용하였다. 거듭제곱 지수와 3차원 해석의 효과를 나타내기 위한 지수 및 멱 법칙 점진기능재료 판의 동적 해석결과를 제시하였다. 기존의 2차원 고차전단변형 이론 및 3차원 이론과의 관계를 수치해석 결과를 통하여 고찰하였다. 또한 (i) 거듭제곱 지수, (ii) 폭-두께 비, 그리고 (iii) 탄성지반 계수, 등이 점진기능재료 판의 자유진동수에 미치는 효과에 대하여 관찰하였다. 본 연구의 결과를 검증하기 위해 참고문헌의 결과들과 비교 분석하였다.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1748-1755
• /
• 2001

The shell and tube heat exchangers were introduced to apply to a big capacity condenser and a high pressure feed water heater for power plant in the beginning of 1990s. Design and manufacturing technology fur shell and tube heat exchangers have been developed until now. But it is very difficult to calculate the expected performance characteristics of the shell and tube heat exchanger, because there are many design parameters to be considered according to internal structure and the shell side heat transfer mechanism complicately related to the design parameters. Design parameters to be considered in the design stage of shell and tube heat exchanger are shell and tube side fluids, flow rate, inlet and outlet temperature, physical properties, type of heat exchanger, outer diameter, thickness, length of tube, tube arrangement, tube pitch, permissive pressure loss on both sides, type of baffle plate, baffle cutting ratio. The propose of study is an analysis TEMA(Tubular Exchanger Manufacturers Association) E shell and tube heat exchanger performance with changing a number of baffles(3, 5, 7, 9, 11) and tubes(16, 20) and determined optimal baffle spacing.

• 대한인간공학회지
• /
• 제25권2호
• /
• pp.107-118
• /
• 2006

Recently, Korean's 3-D foot data have been extensively collected through 5th national anthropometric survey known as 'Size Korea'. In this study, Korean foot shape was investigated and subsequently classified, based on the existing standard for foot shaping. This study analyzed and categorized Korean foot shapes through the following methods. Although the data used in this study were limited to those of Korean adults, major factors affecting the foot shape were deduced and then categorically grouped by the multivariate statistical analysis. For those whose age ranged from 14 to 70, major factors affecting the foot shape for the male were related to foot breadth, ankle thickness, 1st toe shape, malleolus height, heel to top of the foot length, the ratio between toe-side and heel-side and 5th toe shape. For the female, the ball of foot height was added to the above factors. From the factors extracted, the Korean foot shape was categorized into three groups for the male and four groups for the female. They were the ladder type, the inverted triangle type and the square type. For the female, the triangular type was added to the three types. These findings will serve as useful information for the footwear production industry in Korea.

• Steel and Composite Structures
• /
• 제22권6호
• /
• pp.1239-1259
• /
• 2016

The modified couple stress-based third-order shear deformation theory is presented for sigmoid functionally graded materials (S-FGM) plates. The advantage of the modified couple stress theory is the involvement of only one material length scale parameter which causes to create symmetric couple stress tensor and to use it more easily. Analytical solution for dynamic instability analysis of S-FGM plates on elastic medium is investigated. The present models contain two-constituent material variation through the plate thickness. The equations of motion are derived from Hamilton's energy principle. The governing equations are then written in the form of Mathieu-Hill equations and then Bolotin's method is employed to determine the instability regions. The boundaries of the instability regions are represented in the dynamic load and excitation frequency plane. It is assumed that the elastic medium is modeled as Pasternak elastic medium. The effects of static and dynamic load, power law index, material length scale parameter, side-to-thickness ratio, and elastic medium parameter have been discussed. The width of the instability region for an S-FGM plate decreases with the decrease of material length scale parameter. The study is relevant to the dynamic simulation of micro structures embedded in elastic medium subjected to intense compression and tension.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1359-1364
• /
• 2004

An experiment was performed to study the evaporation heat transfer and the pressure drop characteristics of liquid nitrogen in a horizontal stainless steel tube with wire coil inserts. The inner diameter of test tube is 4.3mm and the length is 1.5m. Four wire coils having different pitch and thickness were inserted into the plain test tube. The wire coil length is 1.5m and the diameter is 3.65mm with thickness of 0.5mm and 0.9mm. Experiments were conducted at saturation temperature of $-191^{\circ}C$ mass flux from 200 to 370 $kg/m^{2}s$ and heat flux of 62 $kW/m^{2}$. Direct heating method was used to apply heat to the test section. Boiling heat transfer coefficients of both the plain and the enhanced tubes were calculated. Pressure drops between inlet and outlet side of test section were also measured, and they are used to estimate EPR(Enhancement Performance Ratio).

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1996년도 The 9th KACG Technical Annual Meeting and the 3rd Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.519-521
• /
• 1996

Emerald (3BeO.Al2O3.6SiO2 : Cr3+) single crystals were crystals were grown by reflux method of temperature gradient in the flux solution of Li2O-MoO3-V2O5 system. The composition of flux materials were 3 mole ratio of MoO3-V2O5/Li2O, subtituted 0.2 mole% of K2O, Na2O, Nb2O5 etc to Li2O content, solved 10-15% of beryl to flux quantity and doped 1% of Cr2O3 to emerald amount. Those of mixing were melted at 110$0^{\circ}C$ in Pt containers of the 3 zone furnace of melt-growth-return to circulate continniously, specially it has been grown large emerald single crystal when thermal fluctuation was treated for 2hrs of once time a day at 1050-95$0^{\circ}C$ in growth zone, substitutional solid solution effect of Cr+3 ion for Al+3 to the growth of emerald single crystal was good. Emerald single crystals were c(0001) hexagonal crystal face of preferencial growth direction and m(1010) post side. When it had been durated for 5 months emerald single crystals of the firet size of 0.6mm thickness of seed crystal were grown 32$\times$65mm(c x m) of maximum size and 6.2mm thickness.

• Archives of Plastic Surgery
• /
• 제40권4호
• /
• pp.403-408
• /
• 2013

Background For patients with neuropathy, vasculopathy, and impairment of wound healing, treatment of a diabetic foot ulcer poses many challenges. A large number of dermal analogues have been invented in an effort to overcome these challenges. Matriderm, a dermal analogue, is made from bovine collagen and elastin. This study was conducted in order to evaluate the effectiveness of Matriderm for treatment of diabetic foot ulcers, in comparison with skin grafting. Methods Sixty patients with diabetic foot ulcer were included in this prospective study. The average age of the patients, who had type II diabetes mellitus, was 58 years old. The patients were allocated to an experimental or control group with their consents. The patients were selected with their consent for inclusion in an experimental group and a control group. Patients in the experimental group received a Matriderm appliance and a split-thickness skin graft, while those in the control group received only a split-thickness skin graft. Results A shorter hospitalization period (7.52 weeks) was observed in the experimental group than in the control group (9.22 weeks), and a shorter period of time (8.61 weeks) was required for complete healing, compared with the control group (12.94 weeks), with statistical significance (P<0.05). A higher elasticity ratio of the affected side to the non-affected side was observed in the experimental group, compared with the control group (P<0.01). Conclusions Matriderm enables effective healing and improves elasticity in treatment of patients with diabetic foot ulcer.

• 마이크로전자및패키징학회지
• /
• 제27권3호
• /
• pp.61-67
• /
• 2020

본 논문에서는 FEM(유한요소) 기법을 사용하여 칩이 실장되는 않은 substrate와 칩이 실장된 substrate의 warpage를 해석하여 칩의 실장이 warpage에 미치는 영향을 비교·분석하였다. 또한, warpage를 감소시키기 위한 substrate의 층별 두께의 영향도 분석과 층별 두께 조건을 다구찌법에 의한 신호 대 잡음 비로 분석하였다. 해석 결과에 의하면 칩이 실장되면 substrate의 warpage는 패턴의 방향이 변할 수 있고, 칩이 실장되면서 패키지의 강성도(stiffness)가 증가하고, 패키지 상·하의 열팽창계수의 차이가 작아지면서 warpage는 감소하였다. 또한, 칩이 실장되지 않은 substrate를 대상으로 설계 파라메타의 영향도 분석 결과에 의하면 warpage를 감소시키기 위해서는 회로층 중에서 내층인 Cu1과 Cu4를 중점 관리하고, 다음으로 바닥면의 solder resist 층의 두께와 Cu1과 Cu2 사이의 프리프레그 층의 두께를 관리해야 한다.

• 한국인터넷방송통신학회논문지
• /
• 제20권6호
• /
• pp.21-26
• /
• 2020

본 논문에서는 자수된 SF-MPAA 구현을 위해 방사체를 자수로 구현할 경우 방사체 구조에 따른 SF-MPAA의 특성을 조사 하였다. 자수된 방사체의 길이방향의 그리드 수와 폭 방향의 그리드 수를 줄여서 피치를 늘렸을 때 안테나 이득과 공진주파수는 추세적으로 감소하였다. 그러나 안테나 특성은 폭 방향의 피치에는 크게 영향을 받으나 길이 방향의 피치에는 상대적으로 영향을 적게 받았다. 따라서 도체비율을 줄이기 위해 길이 방향의 그리드 수를 줄이는 것이 유리함을 알 수 있었다. SLL은 피치보다는 길이와 폭 방향 피치의 조합에 영향을 받았다. 자수된 방사체의 도체비율은 자수실 굵기에 대한 피치의 비율로 결정이 되었다. 이 비율이 5이하에서는 도체비율이 급격히 감소했고 5이상에서는 포화되어 서서히 감소했다.