• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.74-81
• /
• 2010

A modeling methodology for the analysis of injection-locked Fabry-Perot laser diodes (FP-LDs), promising for cost-effective WDM-PON sources, is proposed. The time-domain large-signal model that is used is found to provide quite similar results to some experimental ones. With our methodology, we model characteristics of FP-LDs, such as influence of reflectivity at a facet and detuning on injection-locking. The eye diagram characteristics are also investigated. It is observed that the facet reflectivity at the injection side should be lower than 1% to provide stable operation in terms of good side-mode suppression ratio and independence from detuning between narrow-band injection noise and LD modes. It is also observed that good eye opening can be obtained for 155 Mbps modulation while the parameters such as the active region thickness should be properly optimized to obtain reasonable eye opening at 1.25 Gbps.

• Journal of Oral Medicine and Pain
• /
• v.48 no.3
• /
• pp.106-111
• /
• 2023

Purpose: In this study, we evaluate the potential of the relative ratio of capsular width (RCW) between the affected side (Aff) and non-affected side (Non-aff) in patients with temporomandibular joint (TMJ) arthralgia. We assessed whether RCW may hold greater diagnostic significance than the objective capsular width (CW) reported in previous studies when diagnosing arthralgia using ultrasonography (US). Methods: Forty-nine patients were assessed using US, excluding four patients with bilateral arthralgia. The patients were divided into two groups: 40 with unilateral arthralgia (UA), and nine without arthralgia (NA). We measured CW and masseter muscle thickness using US. Moreover, we employed RCW to analyze the variances between the groups. The numerical rating scale (NRS) and RCW were compared before and after dexamethasone injection in 10 patients who underwent follow-up evaluations. Results: Within the UA group, CW on the Aff was found to be significantly larger compared to the Non-aff (p<0.001). Additionally, RCW in the UA group was greater than that in the NA group (p<0.01). Furthermore, after dexamethasone injection, a reduction in the NRS and RCW values was observed in the 10 patients who were followed up. Conclusions: While previous studies have suggested a link between arthralgia and TMJ effusion, making CW a possible indirect diagnostic indicator for arthralgia, our findings propose that RCW could hold more diagnostic value than objective CW. However, additional studies are required to standardize the protocols for interpreting US results and determining the cutoff value of RCW in diagnosing TMJ arthralgia.

• Structural Engineering and Mechanics
• /
• v.89 no.6
• /
• pp.557-570
• /
• 2024

Due to interfacial ageing, chemical action and interfacial damage, the interface debonding may appear in the interfaces of composite laminates. Particularly, the laminates display a side-dependent effect at small scale. In this work, a three-dimensional (3D) and anisotropic thick nanoplate model is proposed to investigate the effects of imperfect interface and nonlocal parameter on the bending deformation, vibrational response and buckling stability of one-dimensional (1D) hexagonal quasicrystal (QC) layered nanoplates. By combining the linear spring model with the transferring matrix method, exact solutions of phonon and phason displacements, phonon and phason stresses of bending deformation, the natural frequencies of vibration and the critical buckling loads of 1D hexagonal QC layered nanoplates are derived with imperfect interfaces and nonlocal effects. Numerical examples are illustrated to demonstrate the effects of the imperfect interface parameter, aspect ratio, thickness, nonlocal parameter, and stacking sequence on the bending deformation, the vibrational response and the critical buckling load of 1D hexagonal QC layered nanoplate. The results indicate that both the interface debonding and nonlocal effect can reduce the stiffness and stability of layered nanoplates. Increasing thickness of QC coatings can enhance the stability of sandwich nanoplates with the perfect interfaces, while it can reduce first and then enhance the stability of sandwich nanoplates with the imperfect interfaces. The biaxial compression easily results in an instability of the QC layered nanoplates compared to uniaxial compression. QC material is suitable for surface layers in layered structures. The mechanical behavior of QC layered nanoplates can be optimized by imposing imperfect interfaces and controlling the stacking sequence artificially. The present solutions are helpful for the various numerical methods, thin nanoplate theories and the optimal design of QC nano-composites in engineering practice with interfacial debonding.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.95-100
• /
• 2022

In this paper, a power loss analysis technique of a high-frequency transformer of a bidirectional DAB (Dual Active Bridge) converter is reported. To miniaturize the transformer of the dual active bridge converter, a resonant inductor was designed with an air gap included low-coupled rate state core to combine leakage inductor with the resonant inductor which is required for soft-switching. In this paper, leakage inductance and magnetizing inductance, core material, type of winding and winding method are included in the dual active bridge transformer loss analysis process to enable optimal design at the initial design stage. Transformer loss analysis for dual active bridge with a switching frequency of 200 kHz and maximum output of 5 kW was executed, and elements necessary for design based on the number of turns on the primary side were graphed while maintaining the transformer turns ratio and window area. In particular, it was possible to determine the optimal number of turns and thickness of the transformer, and ultimately, the total loss of the transformer could be estimated.

• Wind and Structures
• /
• v.34 no.1
• /
• pp.151-159
• /
• 2022

The aerodynamics of blunt bodies with separation at the sharp corner of the leading edge and reattachment on the body side are particularly important in civil engineering applications. In recent years, a number of experimental and numerical studies have become available on the aerodynamics of a rectangular cylinder with chord-to-thickness ratio equal to 5 (BARC). Despite the interest in the topic, a widely accepted set of guidelines for grid generation about these blunt bodies is still missing. In this work a new, well resolved Direct Numerical Simulation (DNS) around the BARC body at Re=3000 is presented and its results compared to previous DNSs of the same case but with different numerical approaches and mesh. Despite the simulations use different numerical approaches, mesh and domain dimensions, the main discrepancies are ascribed to the different grid spacings employed. While a more rigorous analysis is envisaged, where the order of accuracy of the schemes are kept the same while grid spacings are varied alternately along each spatial direction, this represents a first attempt in the study of the influence of spatial resolution in the Direct Numerical Simulation of flows around elongated rectangular cylinders with sharp corners.

• Journal of Welding and Joining
• /
• v.26 no.1
• /
• pp.69-75
• /
• 2008

Spot welding which use the main process for side block production of stainless steel railway vehicle is legged behind in laser welding about a quality and productivity. Although the laser welding has many potential advantages such as low heat input and aspect ratio of weld bead, its application to a new structural component still is required many engineering data including mechanical properties such as tensile, fatigue strength, etc on. Therefore, experimental analysis was carried out to understand the fatigue phenomena of different thickness stainless steel overlap joining panels by Nd:YAG laser welding. The fatigue life curves were obtained through fatigue tests with the various levels of applied load. The fatigue life is related with the parameters such as gap size and penetration depth through experiment. As the results, tensile strength and fatigue life were proportional in heat input level and gap was identified the major factor for fatigue life. Also we could know that deferent a-ferrite content at HAZ depend on welding heat input was important factor to determine a formation of initial crack and total fatigue life cycle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.262-273
• /
• 1991

In the present study, the steady, incompressible, isothermal, developing flow in a 90.deg. rectangular cross sectional strongly curved duct with aspect ratio 1:1.5 and Reynolds number of 9.4*10$^{4}$ has been investigated. Measurements of components of mean velocities, pressures, and corresponding components of the Reynolds stress tensor are obtained with a hot-wire anemometer and pitot tube. In general, flow in a curved duct is characterized by the secondary vortices which are driven mainly by centrifugal force-radial pressure gradient imbalance, and the stress field stabilizing effects near the convex wall and destablizing effects close to the concave wall. It was found that the secondary mean velocities attain values up to 39% of the bulk velocity and are largely responsible for the convections of Reynolds stress in the cross stream plane. Therefor upstream of the bend the Reynolds stress are low. Corresponding to the small boundary layer thickness. At successive planes, large values of Reynolds stress were observed near the concave surface and the side wall.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.37-40
• /
• 2005

High Performance Concrete(HPC) has been widely used in high-rise building. The HPC has several benefits including high strength, high fluidity and high durability. However. spatting is susceptible to occur in HPC and HPC also tends to be deteriorated in the side of fire resistance performance at fire. This paper focuses on the analysis of the temperature history and residual compressive strength with finishing material, in order to protect HPC from sudden-high-temperature, which is one of the main reason spatting occurs. Test results show that spalling occurs in all specimens. The most serious spalling took placed in HPC covering fire enduring spray-on material, whose covering thickness is 20mm but temperature history indicates that fire enduring spray effectively protected HPC from fire for more than 2hours. In addition, residual compressive strength ratio of HPC using fire enduring paint was more than $90\%$ of original strength, thus minimizing spatting and indicating significant fire resistance performance.

• Smart Structures and Systems
• /
• v.21 no.1
• /
• pp.75-97
• /
• 2018

In this paper, a novel higher-order shear deformation theory (HSDT) is proposed for the analysis of the hygro-thermo-mechanical behavior of functionally graded (FG) plates resting on elastic foundations. The developed model uses a novel kinematic by considering undetermined integral terms and only four variables are used in this model. The governing equations are deduced based on the principle of virtual work and the number of unknown functions involved is reduced to only four, which is less than the first shear deformation theory (FSDT) and others HSDTs. The Navier-type exact solutions for static analysis of simply supported FG plates subjected to hygro-thermo-mechanical loads are presented. The accuracy and efficiency of the present model is validated by comparing it with various available solutions in the literature. The influences of material properties, temperature, moisture, plate aspect ratio, side-to-thickness ratios and elastic coefficients parameters on deflections and stresses of FG plates are also investigated.

• Structural Engineering and Mechanics
• /
• v.75 no.2
• /
• pp.193-209
• /
• 2020

This paper presents a new hyperbolic shear deformation plate theory including the stretching effect for free vibration of the simply supported functionally graded plates in thermal environments. The theory accounts for parabolic distribution of the transverse shear strains and satisfies the zero traction boundary conditions on the surfaces of the plate without using shear correction factors. This theory has only five unknowns, which is even less than the other shear and normal deformation theories. The present one has a new displacement field which introduces undetermined integral variables. Material properties are assumed to be temperature-dependent, and graded in the thickness direction according to a simple power law distribution in terms of the volume power laws of the constituents. The equation of motion of the vibrated plate obtained via the classical Hamilton's principle and solved using Navier's steps. The accuracy of the proposed solution is checked by comparing the present results with those available in existing literature. The effects of the temperature field, volume fraction index of functionally graded material, side-to-thickness ratio on free vibration responses of the functionally graded plates are investigated. It can be concluded that the present theory is not only accurate but also simple in predicting the natural frequencies of functionally graded plates with stretching effect in thermal environments.