• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.125-126
• /
• 2021

In order to improve the housing culture, construction changes for the utilization of diverse and multifunctional spaces are appearing in response to the increasing diverse needs of consumers. Cellular Light-weight Concrete (CLC) is being developed for use in fire-resistant heat-insulating walls and non-bearing walls. However, manufacturing non-uniformity has become a problem as a drawback due to the use of foamed bubbles and normal temperature curing, and additional research is required. Therefore, in order to suppress cracks due to drying shrinkage, silica sand is mixed with CLC to try to understand its characteristics. In the experiment, the compressive strength from 7 to 28 days of age was measured via a constant temperature and humidity chamber, and the drying shrinkage was analyzed according to each condition using a strain gauge. The compressive strength of matrix tends to decrease as the substitution rate of silica sand increases. This is judged by the result derived from the fact that the specific surface area of silica sand is smaller than that of slag. Based on KS F 2701 (ALC block), the compressive strength of 0.6 products is 4.9 MPa or more as a guide, so the maximum replacement rate of silica sand that satisfies this can be seen at 60%. Looking at the change in drying shrinkage for just 7 days, the shrinkage due to temperature change and drying is 0.7 mm, and the possibility of cracking due to shrinkage can be seen, and it seems that continuous improvement and supplementation are needed in the future.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.150-151
• /
• 2021

This study aims to achieve an enhancement in the quality of high strength concrete through a reduction in autogenous shrinkage by supplying the moisture needed for hydration through recycled aggregates that retain high amounts of moisture. The result showed that, moisture supply increased with the higher replacement rate, autogenous shrinkage dropped by up to 45 percent.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.437-442
• /
• 2002

Drying shrinkage is the decrease in the volume of a concrete element when it loses moisture by evaporating. Because of low water/binder ratio(W/B) and the use of chemical and mineral admixtures for high-strength concrete, the evolutions of moisture and the rate of cement hydration in high- strength concrete are significantly different from those in normal strength concrete. In this study, the drying shrinkage of high-strength concrete with and without fly ash was measured up to the age of 200 days. From the experimental test results, it was observed that the drying shrinkage decreased as the W/B decreased. As the W/B is lowered from 0.50 to 0.27, the difference of drying shrinkage between the fly ash concrete and the ordinary concrete is gradually increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.308-311
• /
• 2004

Nowadays, plastic industry has needed to produce parts that require high precision and quality. To make a high precision and quality part, before injection molding, plastic material is investigated about their properties such as shrinkage, warpage, etc. In this study, experiments were conducted with PA6(polyamid) to figure out shrinkage behavior according to three type aspect ratio of samples. The injection speed that affects on shear rate, molecular orientation within plastic part was determined as main variable of experiment. As a result of experimental study, part shrinkage had a tendency to be decreased by increasing injection speed and aspect ratio of samples.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.718-724
• /
• 1999

Densification and grain growth behavior of bimodal size distributed alumina powder mixtures were investigated as a function of amount of coarse alumina powder. The specimens which contained coarse alumina powder for 60to 80wt% showed the highest green density. The amount of shrinkage of sintered specimen lineraly decreased with the increase of coarse alumina powder up to the content that showed the highest green density and then further addition of coarse alumina powder led to drastic decrease of shrinkage of specimen. Especially crack-like void were concurrently revealed in the sintered body with addition of coarse alumina powder above 60wt% When the sintering temperature increased up to 1650$^{\circ}C$ the amount of shrinkage of specimen linearly decreased and the grain growth were also retarded with increase of coarse lauminia powder.

• Journal of the Korean Home Economics Association
• /
• v.17 no.4
• /
• pp.15-22
• /
• 1979

This paper was studied changes of physical properties of Lining fabrics by washing and difference between dry method. I experimented four kinds of Lining fabrics for the sample . The analysis was performed by correlation coefficient analysis and significance tested between correlation coefficients. The results are summarized as follows : 1) Increasing rate of shrinkage tends to call high density and weight. 2) Rayon fabrics is shown the most high rate of shrinkage and decreasing strength by increasing washing times. 3) Drip dry makes little change of physical properties. 4) Polyester fabrics is little by washing times and dry method.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.4
• /
• pp.393-400
• /
• 2012

The effect of ground granulated blast-furnace slag (GGBS) and alkaline activator on the properties of setting, compressive strength, drying shrinkage and resistance of carbonation was assessed to develop high volume slag concrete, the GGBS replacement rate of which was more than 80 percent. The changes in the concrete as the replacement rate of GGBS increases were as follows. Initial and final setting time was delayed by two and a half hours, and the compressive strength development properties of concrete in early and long term age were decreased. Drying shrinkage was satisfactory as below $6{\times}10^{-4}$ in every mixture, and yet showed a tangible trend by replacement rate. Carbonation was materially increased. Setting time and early strength development property, however, were extremely advanced by the addition of the alkaline activator. While drying shrinkage was improved by the alkaline activator, resistance to carbonation was not.

• Journal of Adhesion and Interface
• /
• v.5 no.3
• /
• pp.10-17
• /
• 2004

We investigated the effect of stabilization processing parameters on the thermal shrinkage, thermal stability and microstructure of rayon fabrics stabilized under various conditions such as heating rate, stabilization temperature, atmosphere gas, and chemical treatment. The presence and absence of phosphoric acid treatment and the heating rate have most importantly influenced the thermal shrinkage and the weight change of rayon fabrics. Especially, the phosphoric acid treatment decreases the reduction of thickness, length, and weight of the fabrics by about 80%, 20%, and 26%, respectively, in comparison with the untreated counterparts, showing the protective effectiveness of the thermal shrinkage involved. The thermal stability of stabilized rayon fabrics is also affected by all the processing conditions used: stabilization temperature, phosphoric acid treatment, atmosphere gas, and heating rate. In addition, the surface and diameter of the stabilized fiber significantly depend on the treatment of phosphoric acid prior to stabilization process.

• Journal of Biosystems Engineering
• /
• v.41 no.1
• /
• pp.34-42
• /
• 2016

Purpose: This study was performed to improve the drying quality and drying rate of ginseng slices by combining microwave and far-infrared drying techniques. Methods: Based on single-factor experiments and analyses, a quadratic regression orthogonal rotation combination design was adopted to study the effects of the moisture content at the conversion point between the microwave and far-infrared techniques, the ginseng slice thickness and the far-infrared drying temperature on the chip drying time, the surface color difference value, the nutritional composition and the surface shrinkage rate index. Results: Compared to the far-infrared drying alone, the combined microwave and far-infrared drying resulted in an increase in the saponin content of the ginseng slices and reductions in the drying time, surface color difference, and shrinkage rate. Conclusions: We established a mathematical model of the relationships between the surface shrinkage rate index and the experimental factors using the multi-objective nonlinear optimization method to determine the optimal parameter combination, which was confirmed to be the following: microwave and far-infrared moisture contents of 65%, a ginseng slice thickness of 1 mm, and a far-infrared drying temperature of $54^{\circ}C$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.6
• /
• pp.99-104
• /
• 2019

In the present study is focused on the evaluation of the shrinkage characteristics of mix proportion using viscosity agent for printing. Also, another purpose is to compare the shrinkage properties of the mold cast specimen with the additive manufactured specimen using 3D printing techniques. Viscosity agent makes the shrinkage was reduced by an average of 25% (as of 56 days) compared to the reference mix. The effects of reduced shrinkage were also founded, with a reduction of about 15% (as of 28 days).As a result of evaluating the shrinkage using the additive manufactured specimen and the mold cast specimen prepared by the printing mix, the shrinkage of the additive manufactured specimen was reduced by about 25% (based on 28 days). Based on the results of this study, it is possible to predict the shrinkage rate and the occurrence of cracks due to shrinkage on the printing of cement-based composite materials using 3D printing.