• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.4
• /
• pp.332-337
• /
• 2023

Korea is not only surrounded by the sea on three sides, but also has national and local rivers extending 26,843 km, so it has a geographical feature in which abundant sea and inland water surface coexist. As the number of ships operating in the inland waters is continuously increasing due to the improvement of national income, the risk of ship accidents and human casualties in the inland waters is also increasing. In this study, a macroscopic plan for the safety management of inland water ships was presented through investigation of inland water related laws and operation status analysis. As an improvement plan, as a hardware infrastructure it is proposed to secure sufficient inland water fire-boats to secure the golden time for early response to accidents and lifesaving, and to operate an institution specializing in the prevention of inland water ships accidents. And as a software infrastructure, establish departure control standards for inland water ships and the safety diagnosis system currently applied only to sea going ships, the introduction of a system tailored to the characteristics of inland water ships. The proposed inland water safety management policy is expected to contribute to the preparation of prompt and systematic countermeasures in the event of an inland water ship accident, and it is hoped that it will serve as an opportunity to continue to pay attention to safety-related research on inland water ships, which was briefly activated after the sinking of M/V Sewol.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.3
• /
• pp.108-114
• /
• 2015

Ballast water is carried by ships to ensure stability, trim and structural integrity. When a ship loads cargo, the ballast water is discharged. When foreign marine microorganisms are introduced into new marine environments, they pose a threat to the local marine ecological system. UV system is commonly used for the disinfection of waste and surface water. This method would not be as efficient because some species do survive to form viable populations, much of the sediment and organisms at the bottom of tanks, and may become serious pests. In this paper, we designed and implemented ballast water treatment system using fuzzy PID controller to prevent lamp damage, and to reduce the formation of the viable populations. The experiments were conducted with ballast water treatment system using fuzzy PID controller with short time exposure to the temperature above $40^{\circ}C$. This system was shown to be effective by significantly reducing bacterial population and lamp life extension through appropriate temperature of ballast water.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.5
• /
• pp.488-497
• /
• 2009

The freak wave, also known as New-Year-Wave in the north Atlantic, is relatively large and spontaneous ocean surface wave that can sink even large ships and destroy maritime structures. To understand oceanic conditions that develop freak waves, we simulated and generated two versions of scale-downed waves (1:64 and 1:42) in a numerical wave tank and compared the results with the experiment in wave flume. Both of the breaking and non-breaking waves were generated in the simulation. The numerical simulation was implemented based on the finite volume method and a genetic optimization algorithm. Random values were assigned as the initial values for the parameter in the control function, which produced signals representing the motion of wave-maker. The same signal obtained from the optimization process was used for both of the simulation and the experiment. By varying the object function and restrictions of the simulation, a best profile of design wave was selected based on the characteristics, height and period of simulated waves. Results showed that the simulation and experiment with the scale of 1:42 agreed better with freak waves in the natural condition. The presented simulation method will contribute to saving the time and cost for conducting subsequent response analyses of motion under freak waves in the course of the model test for ship and maritime structure.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.6
• /
• pp.51-60
• /
• 2010

In this study, the performance evaluation of a conventional wave resonator at the entrance of a port or a pier against secondary undulation has been performed using 2D hydrodynamic modeling within port. A wave resonator has been designed for the attenuation of the secondary undulation induced by the long-periodic waves. The controlled performance of the wave resonator has been numerically investigated for CGWAVE MODULE of finite-element model of SMS (Surface water Modeling System) based on the elliptic mild-slope wave equation. SMS was verified though the comparisons with analytical solution performed by Ippen and Goda (1963). Also, It was confirmed that a wave resonator of a rectangular model harbor is effective enough to control the secondary undulation when it compares variation of water level with the case of no resonance system. From the above results, amplification phenomenon induced by long-period waves transferred from 1900 sec to 2100 sec when it applied a wave resonator in Busan Gamcheon Port which is a deep-sea. And it was confirmed that a wave resonator of Pohang New Port attenuates largely long-period waves which are within the range of 300 sec induced by long-period motion of the moored ship.

• Journal of Power System Engineering
• /
• v.20 no.2
• /
• pp.51-57
• /
• 2016

Non-esterified biodiesel fuel is cheaper than esterified that because of a simple manufacturing process that only consists of filtering. Applicability of this on diesel engine with electronic control system was accomplished, then optimization adopting a fractional factorial design and response surface methodology was carried out at 25% and 50% of engine load in this study. Pressure of common rail and injection timing mainly effected on responses as specific fuel oil consumption and nitrogen oxides regardless of engine load. Estimations were 310.3 g/kWh of specific fuel oil consumption and 237 ppm of nitrogen oxides at 25% load, and 233.2 g/kWh of specific fuel oil consumption and 730 ppm of nitrogen oxides at 50% load. Tests to verify these estimations were accomplished and as the results, specific fuel oil consumption was 300.4 g/kWh and NOx was 277 ppm at 25% load and 236.8 g/kWh and 573 ppm at 50% load.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.15 no.1
• /
• pp.17-23
• /
• 2009

Current status on consumption and packaging of sweet persimmons in USA was surveyed by visiting the market, and three sea shipments were conducted as model export trial from Korean to USA with measurement in ship container temperature and fruit quality. Strategy to promote the export of Korean persimmons was derived. There have been gradual decrease in the price of persimmons due to their increases production, but there seems potential growth in consumption of the fruits from Asian, Hispanic and American people. Compared to the fruits from other countries, Korean persimmons are desired to have higher soluble solid content with stronger red color, but too large sizes are not favored in American market. There has often been temperature fluctuation in shipment container during the sea transport to USA, resulting in surface blackening, skin black spotting and flesh softening. Plastic bag packages with inappropriate unitizing crimping were found to sometimes build up unproper modified atmosphere (high $O_2$ and low $CO_2$) giving high rate of physiological injury.

• Journal of Navigation and Port Research
• /
• v.37 no.3
• /
• pp.257-262
• /
• 2013

A ship operating in rough sea may suffer from an undesirable motion which may severely degrade the performance of equipment onboard and give a person an uncomfortable feeling. Hence, roll stabilization received a considerable attention and various devices including bilge keels, stabilizing fins, gyroscopic, anti-rolling tanks, rudders and flaps have been conceived and utilized for the purpose. The Coanda effect is evident when a jet stream is applied tangential to a curved surface of a hydrofoil since then the jet increases the circulation around the foil and consequently the lift. Model tests and numerical simulation have been conducted to examine the practicality of a fixed type fin stabilizer augmented by the Coanda jet. The results show that the lift coefficient of the modified Coanda fin at the zero angle of attack identically coincides with that of the original fin at ${\alpha}=\26^{\circ}$ when Coanda jet is supplied at the rate of $C_j$ = 0.25. It is also shown that fixed type fin stabilizers for active control of the motions of ships and the other mobile units without rotation can be put to practical use if the Coanda effect is applied.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.