• 한국해안해양공학회지
• /
• 제13권2호
• /
• pp.177-188
• /
• 2001

전난류에서 파와 해류가 합성하였을 때 발생하는 해저면 마찰력을 계산하는 방법을 고찰하였다. 전난류에서 일방향 흐름에 의한 마찰력의 산정방법으로 절점조정법을 제시하였으며, Bijker의 관측자료와 비교하여 절점조정치를 산정하였다. 파와 해류의 합성류에 의한 마찰력 계산방법으로 수정된 Bkjker 모형(BYO Model)과 수정된 Fredsoe 모형(FY Model)을 Bijker의 관측자료에 적용하였으며, BYO 모형에서 최대마찰력을 산정하는데 있어 새로운 개선책을 제시하였다.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제22권1호
• /
• pp.5-10
• /
• 2011

The effect of sample handling condition on the rheological measurement of regenerated silk fibroin formic acid solution using parallel plate geometry was investigated. In case of loading method, the loading by pouring sample solution resulted in the best reproducibility of rheological measurement. Loading with spoon showed a high variance of viscosity value at low shear rate region ($0.01{\sim}1sec^{-1}$) while loading with syringe exhibited a low reproducibility of viscosity at high shear region ($1{\sim}100sec^{-1}$) with a disappearance of shear thinning phenomenon. It was revealed that the sample loading with small extra amount lead to the most reproducible result. The sample loading with the exact amount for the measuring plate resulted in a lack of reproducibility of high shear viscosity, while the loading with large extra volume produced a limited consistency of low shear viscosity. It was turned out that 3 min. of waiting time before measurement was the optimum condition for reliable result. When the waiting time was less than 1 min., the low shear viscosity was obtained with a lack of consistency. On the other hand, the sample solution started drying when the waiting time increased up to 5 min.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1212-1217
• /
• 2008

In this study, in order to clarify the effect of the direction of cyclic shear on the post-earthquake settlement the multi-directional shear tests were carried out for Toyoura Japan standard sand, Genkai natural sand and the Granulated Blast Furnace Slag (GBFS). In a series of tests, number of strain cycles was changed as n=5-200 and the shear strain amplitude varied from 0.1% to 1.0%. The relative density was also changed as Dr=50, 60 and 70%. From the test results for Toyoura sand and GBFS, it is clarified that the post cyclic settlement is relatively large at the small relative density and becomes large with the shear strain amplitude. When the influence of the direction of cyclic shear is decreases, the post cyclic settlement strain for Toyoura sand is converged to a constant value, but the GBFS is increased with the number of strain cycles.

• Korea-Australia Rheology Journal
• /
• 제15권2호
• /
• pp.55-61
• /
• 2003

The steady shear flow properties of vaseline generally used as a base of the pharmaceutical dosage forms were studied in the consideration of wall slip phenomenon. The purpose of this study was to show that how slip may affect the experimental steady-state flow curves of semisolid ointment bases and to discuss the ways to eliminate (or minimize) wall slip effect in a rotational rheometer. Using both a strain-controlled ARES rheometer and a stress-controlled AR1000 rheometer, the steady shear flow behavior was investigated with various experimental conditions ; the surface roughness, sample preparation, plate diameter, gap size, shearing time, and loading methods were varied. A stress-controlled rheometer was suitable for investigating the flow behavior of semisolid ointment bases which show severe wall slip effects. In the conditions of parallel plates attached with sand paper, treated sample, smaller diameter fixture, larger gap size, shorter shearing time, and normal force control loading method, the wall slip effects could be minimized. A critical shear stress for the onset of slip was extended to above 10,000 dyne/$\textrm{cm}^2$. The wall slip effects could not be perfectly eliminated by any experimental conditions. However, the slip was delayed to higher value of shear stress by selecting proper fixture properties and experimental conditions.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.29-34
• /
• 2002

[ $Nb/MoSi_2-ZrO_2$ ] laminate composites have been successfully fabricated by alternately stacking $MoSi_2-ZrO_2$ powder layer and Nb sheet, followed by hot pressing in a graphite mould. The fabricating parameters were selected as hot press temperatures. The instrumented Charpy impact test was carried out at the room temperature in order to investigate the relationship between impact properties and fabricating temperatures. The interfacial shear strength between $MoSi_2-ZrO_2$ and Nb, which is associated with the fabricating temperature and the growth of interfacial reaction layer, is also discussed. The plastic deformation of Nb sheet and the interfacial delamination were macroscopically observed. The $Nb/MoSi_2-ZrO_2$ laminate composites had the maximum impact value when fabricated at 1623K, accompanying the increase of fracture displacement and crack propagation energy. The interfacial shear strength of $Nb/MoSi_2-ZrO_2$ laminate composites increased with the growth of interfacial reaction layer, which resulted from the increase of fabricating temperature. there is an appropriate interfacial shear strength for the enhancement of impact value of $Nb/MoSi_2-ZrO_2$ laminate composites. A large increase of interfacial shear strength restrains the plastic deformation of Nb sheet.

• 대한치과보철학회지
• /
• 제31권2호
• /
• pp.181-190
• /
• 1993

The purpose of this study was to evaluate the effect of shear bond strength between various percentage of reused dental ceramic alloys and porcelain. One hundred specimens were made of one semiprecious alloy and three nonprecious alloys. Each alloy group was subdevided into five groups according to the additional precentage of new alloy. Group I specimens were made of 100% new alloy and served as the control of the investigation. Group II specimens were made of once-cast alloy with 75% new alloy. Group III specimens were made of once-cast alloy with 50% new alloy. Group IV specimens were made of once-cast alloy with 25% new alloy. Group V specimens were made of 100% recast alloy. Five specimens were made for each group of the alloy combinations. The test specimens were prepared by firing porcelain doughnuts on the alloy rod surface, and invested in dental stone. Bond strengths were measured by Instron universal testing machine at a crosshead speed of 0.5mm/min. The fractured surface of metal specimens were examined under the scanning electron microscope. The obtained results were as follows : 1. The shear bond strength of Albabond showed no significant difference between control group and reused alloy group. 2. The shear bond strength of reused alloy groups of nonprecious alloys were lower than that of control groups. 3. The shear bond strength between porcelain and metal in semiprecious alloy was higher than in nonprecious alloys 4. In nonprecious alloys. Rexillium III showed the highest bond strength value and Excelalloy showed the lowest shear bond strength value. 5. Regardless of the type of alloys and additional proportion of new alloys, scanning electron microscope photographs of the fracture surface between alloy and porcelain revealed simillar semiprecious alloy and nonprecious alloys.

• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.597-606
• /
• 1998

The purpose of this study was to evaluate the shear bond strength of the Compoglass Carvifil bonded on the dentin surface according to etching or non-etching and two time application or three time application of single component. Human non-carious 60 extracted 3rd molar were used. The occlusal dentin surfaces of all teeth were exposed with Diamond Wheel Saw and polished with Lapping & Polishing machine(South Bay Technology Co., U.S.A). The teeth were then distributed randomly into four groups of 15 teeth each and dentin surface were conditioned as following. Control group : Non-etching, two times application of Syntac Single Component. (According to manufacture's instruction) Experimental group 1 : Non-etching, three times application of Syntac Single Component. Experimental group : 2 Etching, two times application of Syntac Single Component. Experimental group 3 : Etching, three times application of Syntac Single Component. Compoglass were bonded to exposed dentin surfaces and all samples were placed in distilled water for 7 days. The shear bond strengths were measured by universal testing machine (SHIMADAZU AUTOGRAPH, AGS-4D., Japan). The results were as follows : 1. Experimental group 3 revealed the highest value (30.75${\pm}$4.74 MPa) and control group revealed the lowest value(14.85${\pm}$2.69 MPa). There was significant difference of shear bond strength among four groups(P<0.01) 2. The acid-etching groups (experimental group 2, 3) had higher shear bond strengths than non etching groups(control group and experimental group 1). 3. The additional application of Syntac single component groups revealed a higher bond strength than two times application groups (control group and experimental group 2).

• 한국지반공학회논문집
• /
• 제20권1호
• /
• pp.5-12
• /
• 2004

본 연구는 암반에 근입된 현장타설말뚝의 화강암과 콘크리트의 부착면에서의 전단거동을 이해하려는 데 있다. 암반에 근입된 현장타설말뚝의 전단거동을 실내에서 실험하기 위해서는 현장에서의 전단거동을 모델링 해야 한다. 따라서, 말뚝의 축방향 대칭성을 고려해 암반에 근입된 전단면을 2차원으로 모델링함으로써 일정수직강성도(conctant normal stiffness; CNS) 조건의 전단시험을 실시할 수 있다. 본 논문에서는 국내 화강암을 대상으로 거칠기, 암의 강도, 응력경계조건 등을 고려하여 암-콘크리트 접촉부에 대한 일정수직강성도 전단시험을 수행하였다. 실험결과 각 변수(요철부의 경사각 및 높이, 수직강성도)에 따른 전단특성(첨두전단강도, 전단응력, 수직응력)은 물론 팽창현상(dilation) 등을 관찰할 수 있었다. 시험결과에 따르면 첨두 전단강도는 요철부의 경사각이 증가할수록, 그리고 수직강성도가 증가할 수록 증가하는 것으로 나타났으며, 팽창량은 요철부의 각도가 클수록 수직강성도가 작을수록 크게 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권5호
• /
• pp.182-189
• /
• 2021

VPS는 중공재의 형상을 최적화 하고 중공재의 부상 및 작업하에 의한 이탈을 방지하는 기능을 가진 기존 중공슬래브공법이다. 본 연구에서는 기존연구에서 제안한 거푸집 패널이 부착된 중공슬래브(VPS)를 활용하여 플랫 플레이트의 뚫림전단 안전성을 검토하였다. 실험 결과, 가력점으로 부터 기둥 폭의 2.0배를 넘어 중공재를 배치한 VSPS 실험체는 기준 실험체에 대비 내력이 9.4%감소하였다. KBC2016에서 제시한 설계 값의 약 1.57배 이상의 강도 값을 나타내었다. 중공재를 배치한 VSPS 실험체가 전단파괴가 발생하기 전까지 기준 실험체 대비 강성의 변화는 없는 것으로 나타났다. 이는 휨 철근을 충분하게 배근하여 본 실험이 전단에 의해 파괴되고 있음을 알 수 있다.

• Elastomers and Composites
• /
• 제45권2호
• /
• pp.122-128
• /
• 2010

소수성실리카를 안정제로 하는 현탁중합반응법을 이용하여 합성한 스티렌(St)/부틸메타크릴레이트(BMA) 공중합체 (co-PSB) 입자의 전단점도를 모세관 레오미터 (capillary rheometer)를 이용하여 $170^{\circ}C$에서 측정하였다. co-PSB 입자의 전단점도는 중량평균분자량이 74,800 g/mol 이하인 경우 낮은 전단속도에서는 뉴톤거동을 보였다. 중량평균분자량이 136,800 g/mol을 초과하면서 전단점도는 전단속도의 전 영역에 걸쳐 감소하였고 전단속도에 대한 기울기의 절대값은 분자량의 증가와 함께 증가하였다. St/BMA의 구성비가 7/3, 5/5 및 3/7의 co-PSB 입자는 유사한 분자량을 나타내었지만 BMA의 구성비가 증가하면서 유리전이온도와 전단점도는 감소하였다. St/BMA의 구성비가 1/9 인 co-PSB의 경우 유리전이온도는 더욱 감소하였으나 초기 전단점도는 크게 증가하였다. 카본블랙을 함유하는 co-PSB 복합체 입자의 전단점도는 카본블랙의 증가에 따라 증가하였으나, 카본블랙의 농도에 따른 전단점도의 변화는 분자량 및/혹은 구성비의 변화 효과에 비교하여 미약하였다.