• 콘크리트학회논문집
• /
• 제16권4호
• /
• pp.467-476
• /
• 2004

철근콘크리트(RC)의 경우 철근과 콘크리트의 부착특성에 의한 균열의 제어로 균열 후의 재료모델은 무근콘크리트(PL)와 다르다. 수평력을 받는 RC 기둥의 비선형 거동특성을 기둥의 단면을 영역화(RC영역과 PL영역)하여 각기 다른 재료모델을 적용하여 3차원 해석으로 모사였다. 파괴시 면외방향으로의 전단변형률은 비균일성을 나타내면서 진전되고 이러한 경향은 면외방향으로의 두께가 클수록 강하게 나타났다. 이러한 변형률의 분포특성을 고려하지 않는다면 2차원 해석에서는 기둥의 내하력과 변위성능을 과다하게 예측하게 된다. 인장과 전단모델에서 적절한 등가 경화계수를 도입함으로써 2차원 해석에서도 3차원 해석과 유사한 결과를 얻을 수 있음을 확인하였다.

• 콘크리트학회논문집
• /
• 제13권6호
• /
• pp.602-609
• /
• 2001

중앙부 철골조와 단부 RC조로 이루어진 혼합구조보인 RS보의 전단강도를 예측하기 위한 해석모델로서 Strut-and-Tie Model을 개발하였다. 또한 제안된 모델은 강재매입구간에서의 RC부위에 발생한 전단균열에 의한 콘크리트의 강도저하를 고려하기 위하여, 콘크리트의 연화효과를 고려할 수 있는 모델로 제안되었다. 제안모델은 전단균열이 발생된 혼합구조 보에서 평형방정식, 적합방정식, 구성방정식을 이용하여 전단강도를 구할 수 있으며, 이에 따라 구성재료의 파괴를 예측할 수 있다. 따라서 기존의 식에서 예측하지 못한 콘크리트의 파괴에 의한 전단강도를 예측할 수 있음을 확인하였다. 해석결과 예측전단강도대비 실험강도의 비가 평균 1.02, 표준편차 0.126의 매우 만족스러운 결과를 보였다.

• 한국지반공학회논문집
• /
• 제23권2호
• /
• pp.35-45
• /
• 2007

본 연구에서는 낙동강하상모래에 소량의 포틀랜드시멘트를 고결작용제로 사용한 시멘트혼합토의 제체재료의 적합성검토 설계 및 해석에 필요한 기초자료를 제공하고자 배수조건의 삼축압축시험을 수행하여 시멘트혼합율의 증가에 따른 전단거동을 분석하였다. 시멘트혼합율의 증가에 따라 첨두강도 및 탄성계수는 증가 하였고 시멘트의 결합력에 의하여 다일레이션이 억제되었으나 시멘트 결합력의 파괴후 다일레이션은 증가하였다. 그리고 응력-변형률 곡선에서 연화거동이 나타났으며 시멘트혼합율의 증가에 따라 점착력 및 내부마찰각이 증가하였다.

• 한국재료학회지
• /
• 제23권7호
• /
• pp.373-378
• /
• 2013

In order to clarify the effect of C/Ti atom ratios(${\chi}$) on the deformation behavior of $TiC_{\chi}$ at high temperature, single crystals having a wide range of ${\chi}$, from 0.56 to 0.96, were deformed by compression test in a temperature range of 1183~2273 K and in a strain rate range of $1.9{\times}10^{-4}{\sim}5.9{\times}10^{-3}s^{-1}$. Before testing, $TiC_{\chi}$ single crystals were grown by the FZ method in a He atmosphere of 0.3MPa. The concentrations of combined carbon were determined by chemical analysis and the lattice parameters by the X-ray powder diffraction technique. It was found that the high temperature deformation behavior observed is the ${\chi}$-less dependent type, including the work softening phenomenon, the critical resolved shear stress, the transition temperature where the deformation mechanism changes, the stress exponent of strain rate and activation energy for deformation. The shape of stress-strain curves of $TiC_{0.96}$, $TiC_{0.85}$ and $TiC_{0.56}$ is seen to be less dependent on ${\chi}$, the work hardening rate after the softening is slightly higher in $TiC_{0.96}$ than in $TiC_{0.85}$ and $TiC_{0.56}$. As ${\chi}$ decreases the work softening becomes less evident and the transition temperature where the work softening disappears, shifts to a lower temperature. The ${\tau}_c$ decreases monotonously with decreasing ${\chi}$ in a range of ${\chi}$ from 0.86 to 0.96. The transition temperature where the deformation mechanism changes shifts to a lower temperature as ${\chi}$ decreases. The activation energy for deformation in the low temperature region also decreased monotonously as ${\chi}$ decreased. The deformation in this temperature region is thought to be governed by the Peierls mechanism.

• 대한기계학회논문집
• /
• 제17권7호
• /
• pp.1700-1709
• /
• 1993

The stepped specimen which is subjected to step loading is modeled to study the initiation and growth of adiabatic shear band using explicit time integration finite element method. Three different clearance sizes are tested. The material model for the stepped specimen includes effects of strain hardening, strain rate hardening and thermal softening. It is found that the material inside the fully grown adiabatic shear band experiences three phase of deformation, (1) homogeneous deformation phase, (2) initiation/incubation phase, and (3) fast growth phase. The second phase of deformation is initiated after sudden shear stress drop which occurs at the same time regardless of the clearance size. The incubation time prior to fast growth phase increases, as the clearance size of the stepped specimen increases. Whereas, after incubation period, the growth rate of the adiabatic shear band decreases, as the clearance size decreases. It is also found that two adiabatic shear band may develop instead of one for the smaller clearance size.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.423-436
• /
• 2023

In this research, we tested 10 simply supported concrete-encased composite columns under monotonic eccentric loads and investigated their shear behaviour. The specimens tested were two reinforced concrete specimens, three steel-reinforced concrete (SRC) specimens with an H-shaped steel section (also called a beam section), and five SRC specimens with a cruciform-shaped steel section (also called a column section). The experimental variables included the transverse steel shape's depth and the longitudinal steel flange's width. Experimental observations indicated the following. (1) The ultimate load-carrying capacity was controlled by web compression failure, defined as a situation where the concrete within the diagonal strut's upper end was crushed. (2) The composite effect was strong before the crushing of the concrete outside the steel shape. (3) We adjusted the softened strut-and-tie SRC (SST-SRC) model to yield more accurate strength predictions than those obtained using the strength superposition method. (4) The MSST-SRC model can more reasonably predict shear strength at an initial concrete softening load point. The rationality of the MSST-SRC model was inferred by experimentally observing shear behaviour, including concrete crushing and the point of sharp variation in the shear strain.

• Computers and Concrete
• /
• 제2권6호
• /
• pp.499-516
• /
• 2005

A composite model is used to represent the heterogeneity of plain concrete consisting of coarse aggregates, mortar matrix and the mortar-aggregate interface. The composite elements of plain concrete are modeled using triangular finite element units which have six interface nodes along the sides. Fracture is captured through a constitutive single branch softening-fracture law at the interface nodes, which bounds the elastic domain inside each triangular unit. The inelastic displacement at an interface node represents the crack opening or sliding displacement and is conjugate to the internodal force. The path-dependent softening behaviour is developed within a quasi-prescribed displacement control formulation. The crack profile is restricted to the interface boundaries of the defined mesh. No re-meshing is carried out. Solutions to the rate formulation are obtained using a mathematical programming procedure in the form of a linear complementary problem. An event by event solution strategy is adopted to eliminate solutions with simultaneous formation of softening zones in symmetric problems. The composite plain concrete model is compared to experimental results for the tensile crack growth in a Brazilian test and three-point bending tests on different sized specimens. The model is also used to simulate wedge-type shear-compression failure directly under the loading platen of a Brazilian test.

• 한국추진공학회지
• /
• 제11권6호
• /
• pp.18-25
• /
• 2007

열적으로 민감한 재료의 소성 변형에 있어서, 전단력에 의한 전단밴드(shear band)는 많은 공학적인 재료에서 관찰되고 있으며 전단밴드의 형성이 가속화됨에 따라 밴드의 변화량이 많고 폭이 좁은 국부화(localization) 현상이 발생하게 되는데, 이는 가공물에 치명적인 파단을 가져올 수 있는 현상이다. 본 연구에서는 텅스텐 중합금(tungsten heavy alloy, WHA)의 관통 메커니즘을 분석하기 위해 높은 변형률의 조건하에서 관찰될 수 있는 전단밴드(shear band)의 형성과 국부화 현상에 대하여 열적 조건을 고려하여, 고속변형률에서 다결정 금속의 전단밴드 구성에 기초를 둔 메커니즘을 수치적으로 연구하였다.

• Geomechanics and Engineering
• /
• 제12권3호
• /
• pp.399-415
• /
• 2017

A series of direct shear tests were conducted to investigate the frictional properties of the interface between structures and the filling soil of Chongqing airport fourth stage expansion project. Two types of structures are investigated, one is low carbon steel and the other is the bedrock sampled from the site. The influence of soil water content, surface roughness and material types of structure were analyzed. The tests show that the interface friction and shear displacement curve has no softening stage and the curve shape is close to the Clough-Duncan hyperbola, while the soil is mainly shear contraction during testing. The interface frictional resistance and normal stress curve meets the Mohr-Coulomb criterion and the derived friction angle and frictional resistance of interface increase as surface roughness increases but is always lower than the internal friction angle and shear strength of soil respectively. When surface roughness is much larger than soil grain size, soil-structure interface is nearly shear surface in soil. In addition to the geometry of structural surface, the material types of structure also affects the performance of soil-structure interface. The wet interface frictional resistance will become lower than the natural one under specific conditions.

• 소성∙가공
• /
• 제9권4호
• /
• pp.395-403
• /
• 2000

Formation of Shear Band under the adiabatic condition is widely observed In the engineering materials during rapidly forming process lot a thermally rate-dependent material. The shear band stems from evolution of a narrow region in which an intensive plastic flow occurs. The shear band often plays a role of a precursor of the ductile fracture during a forming process. The objective of this study is to investigate the localization behavior using numerical method. In this work, the implicit finite difference scheme is employed due to the ease of convergence and the numerical stability It is noted that physical and mechanical properties of materials determine how the shear band is formed and then localized. Material properties can be characterized with inertia number dissipation number and diffusion number. It is observed that the dimensionless numbers effect on localization. Using a parametric study, comparison was made between CRS-1018 steel with WHA (tungsten heavy alloy). The deformation behavior of material in this study include an isotropic hardening as well as thermal softening. Moreover, this study suggests that a kinematic hardening constitutive relation be required to predict a more accurate strain level at a shear band.