• 제어로봇시스템학회논문지
• /
• 제9권1호
• /
• pp.10-21
• /
• 2003

During seek operation in disk drives, the recording head is moved toward desired track by seek servo controller and then is settled onto the center of the desired track by settling servo controller. If the head speed at the start of settling servo control is not slow, it may produce overshoot relative to the center of track and thus extend the settling time. The degradation in settling performance will be more severe as the track width becomes smaller for higher density of data storage. We design a new settling servo controller for minimizing settling time based on the pole-zero cancellation. In order to cancel slow poles in settling response, we apply discrete pulse signals to the system in addition to the state feedback control. For exact pole-zero cancellation, we consider the dynamics of power amplifier used for actuator current regulation and the effects of delay in control action. In addition, we present system parameter identification algerian for the robustness of our controller to system parameter variation. In order to demonstrate the practical use of our controller, we present experimental results obtained by using a commercially available disk drive.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제51권6호
• /
• pp.252-257
• /
• 2002

We designed a neuro-fuzzy controller to improve some problems that are happened when the DC servo motor is controlled by a PID controller or a fuzzy logic controller. Our model proposed in this paper has the stable and accurate responses, and shortened settling time. To prove the capability of the neuro-fuzzy controller designed in this paper, the proposed controller is applied to the speed control of DC servo motor. The results showed that the proposed controller did not produce the overshoot, which happens when PID controller is used, and also it did not produce the steady state error when FLC is used. And also, it reduced the settling time about 10%. In addition, we could by aware that our model was only about 60% of the value of current peak of PID controller.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권12호
• /
• pp.616-623
• /
• 2003

Conventional P/PI speed controller of today's servo drives should be manually tuned the controller switching set-point by trial-and-errors, which may translate the drive system down-time and loss of productivity. The adjustable drive performance is heavily dependent on the quality of the expert knowledge and becomes inadequate in applications where the operating conditions change in a wide range, i.e., tracking command, acceleration/deceleration time, and load disturbances. In this paper, the demands on simple controls/setup are discussed for industry servo drives. Analyzing the frequency content of motor torque command, P/PI control mode switching is automatically performed with some prior knowledge of the mechanical dynamics. The dynamic performance of the proposed scheme assures a desired tracking response curve with minimal oscillation and settling time over the whole operating conditions. For comprehensive comparison of traditional P/PI control scheme, extensive test is carried out on actual servo system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.424-427
• /
• 2002

Pneumatic control systems have the potential to provide high output power to weight and size ratios at a relatively low cost. However, they are mainly employed in open-loop control applications where positioning repeatability is not of great importance. This paper presents precision positioning control of pneumatic servo cylinder with on-off valve, Pneumatic low-friction cylinder with servo valve and DC servo motor under parameter variations. Basically positioning control uses PID controller, where needs a linearized model. A neural network is added to a PID controller to compensator nonlinearity of the system and an influence of friction force is consider as disturbance. The performances of the proposed algorithms were compared by experiments with them of PID controller. From those experiments is was shown that the proposed algorithms are more efficient about settling time, steady 7tate error and overshoot than PID control algorithm.

• 전력전자학회논문지
• /
• 제7권5호
• /
• pp.465-471
• /
• 2002

본 논문에서는 산업용 서보 구동 시스템의 새로운 PID 속도 제어기를 제안한다. 제안된 속도 제어기는 전류 제어 루프의 주파수 대역에 의해서 속도 제어 루프의 대역폭이 자동적으로 결정되고, 속도제어 루프의 지연을 고려하여 제어기 이득이 자동적으로 선정이 된다. 제안된 설계 방식은 그 자체로 최소한의 오버슈우트와 진동을 갖는 빠른 속도 응답을 실현한다. 또한, 제안된 방식은 기존의 직렬 구조 형태의 위치제어기에 간단히 적용할 수 있다.

• Journal of information and communication convergence engineering
• /
• 제3권1호
• /
• pp.43-48
• /
• 2005

In this paper, the adaptive fuzzy logic controller(AFLC) is proposed, which uses real-coding genetic algorithm showing a good performance on convergence velocity and diversity of population among evolutionary computations. The effectiveness of the proposed AFLC was demonstrated by computer simulation for speed control system of AC servo motor. As a result of simulation for the AC servo motor, it is shown the proposed AFLC has the better performance on overshoot, settling time and rising time than the PI controller which is used when tuning AFLC.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1988년도 한국자동제어학술회의논문집(국내학술편); 한국전력공사연수원, 서울; 21-22 Oct. 1988
• /
• pp.164-168
• /
• 1988

This paper utilizes an optimal control law for the accurate tracking servo system design. The devivation of a simple control law implementing microprocessor is made to minimize position and speed error of the controller. The 16 bit microprocessor receives command angular position and calculate the control algorithm for accurate tracking and provides control system gain scheduling to achieve very short settling time. Simulation results and some experimental results of the position controlled tracking using 4.5Kw DC servo motor are shown.

• 한국군사과학기술학회지
• /
• 제4권1호
• /
• pp.52-61
• /
• 2001

The purpose of this paper is to study on the control of a self-activated cable spooling system for towed away handling winch using a hydraulic servo driving unit and a cable position measurement mechanism. To design a controller of the cable spooling system, it is carried out the analysis of the hydraulic servo system and derived the relationship of a parameters through the control theory. Also, it is derived from the control specfications using settling rotation angle and spooling safety ratio proposed to the analysis for the behavior of the system. The cable spooling system is tested and evaluated to validate the performance of the controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.250-250
• /
• 2000

The purpose of this paper is to study on the control of a self-activated cable spooling system for towed array handling winch using a hydraulic servo driving unit and a cable position measurement mechanism. To design a controller of the cable spooling system, it is carried out the analysis of the hydraulic servo system and derived the relationship of a parameters through the control theory. Also, it is derived from the control specifications using settling rotation angle and spooling safety ratio proposed to the analysis for the behavior of the system. The cable spooling system is tested and evaluated to validate the performance of the controller.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.544-547
• /
• 2003

The purpose of this paper is to develop the straightforward design guidelines of PD/PID speed controller for Industry servo drives with plug and play concept. The controller gains are uniquely determined from the current control loop dynamics, speed loop delay, and mechanical parameters. In order to eliminate the mechanical friction uncertainties, an automatic PD/PI control mode switching algorithm Is introduced using online spectrum analysis of motor torque command. The dynamic performance of the proposed scheme assures a fast tracking response curve with minimal oscillation and settling time over the whole operating conditions. For comprehensive comparison of conventional PI control scheme, extensive test is carried out on actual servo system.