• Proceedings of the KIEE Conference
• /
• 2005.10a
• /
• pp.150-154
• /
• 2005

This paper is presented for the development of the brushless DC(BLDC) spindle motors for hard disk drives. A new BLDC Motor has the use of insulated, compacted, iron powder for the armature core material of BLDC motors. Insulated iron powder in this paper is generally called soft magnet composite(SMC). The SMC is used for the stator of the motor instead of the laminated steel core. The motor used by SMC can have the good advantages in condition of the high frequency input power and small sized motor. It gets much more high efficiency than laminated steel core at same input power. The proposed motor has a technique of speed sensorless control. Experimental results show the performance of the proposed BLDC spindle motors for an HDD.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.1
• /
• pp.48-52
• /
• 2011

Over the years, traditionally, six-switch three-phase inverters have been widely utilized for variable speed alternating current motor drives. Recently, some efforts have been made on the application of four-switch three phase inverter for uninterruptible power supply and variable speed drives. This is due to some advantages of the four-switch three phase inverter over the conventional six-switch three-phase inverters such as reduced price due to reduction in number of switches, reduced switching losses, reduced number of interface circuits to supply logic signals for the switches, simpler control algorithms to generate logic signals, less chances of destroying the switches due to lesser interaction among switches, and less real-time computational burden. However such as slow di/dt and speed limitation, are the inherent characteristics and main drawbacks of the four-switch configuration. Those problems can be overcome in conjugation with Voltage-doublers which has additional advantage, such as unity power factor correction.

• Journal of Power Electronics
• /
• v.18 no.4
• /
• pp.1086-1098
• /
• 2018

This study presents a new sensorless commutation method for brushless direct current motors to replace Hall sensor signals with virtual Hall signals. The importance of the proposed method lies in the simultaneous elimination of the phase shifter and the low-pass filters, which makes the method simple and cost-effective. The method removes high ripple switching noises from motor terminals, thereby decreasing motor losses. The proposed method utilizes unfiltered line voltages with notches caused by current commutation. Hence, specific sign signals are defined to compensate for the effects of commutation noise. The proposed method is free from phase delay that originates from low-pass filters. The method directly produces virtual Hall signals, and thus, it can be interfaced with low-cost commercial commutation integrated circuits based on Hall sensors. Simulation and experimental results show the effectiveness and validity of the proposed method.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.268-270
• /
• 2009

This paper proposes a simple starting method to arrange the rotor position of the blushless DC motor (BLDC) without additional sensors and any information of motor parameters. Both the stator current and time period for arranging the rotor position can be easily adjusted by modulating a pulse width of switching devices. Using the proposed method, it is demonstrated experimentally that the BLDC starts up very smoothly.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.7-9
• /
• 2007

If used to drive the minicar, the BLDC Motor has advantages of weightless, efficient, small-size and credibleness. In this paper at first the position detecting method for BLDC was introduced, secondly the simulation of control algorithm was done and at last the prototype controller based one chip processor MEGA48 was fabricated. The controller proposed has characteristic of cheap cost, reliable performance and totally meeting demands of minicar control.

• International Journal of Control, Automation, and Systems
• /
• v.6 no.4
• /
• pp.477-487
• /
• 2008

This paper proposes a new position sensorless drive for brushless DC (BLDC) motors. Typical sensorless control methods such as the scheme with the back-EMF detection method show high performance only at a high speed range because the magnitude of the back-EMF is dependent upon the rotor speed. This paper presents a new solution that estimates the rotor position by using an unknown input observer over a full speed range. In the proposed method, a trapezoidal back-EMF is modelled as an unknown input and the proposed unknown input observer estimating a line-to-line back-EMF in real time makes it possible to detect the rotor position. In particular, this observer has high performance at a low speed range in that the information of a rotor position is calculated independently of the rotor speed without an additional circuit or complicated operation process. Simulations and experiments have been carried out for the verification of the proposed control scheme.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1087-1089
• /
• 2003

This paper presents a method to reduce commutation torque ripple in a sensorless brushless DC motor drive without current sensors. To compensate the commutation torque ripple completely, the duration of commutation must be known. The proposed method measures the duration of commutation from terminal voltage waveforms, calculates a PWM duty ratio to suppress the commutation torque ripple from the output of speed controller, and applies the calculated PWM duty ratio only during the commutation. Experimental results show that vibrations are considerably reduced when the proposed method is applied to the sensorless brushless DC moter drive for air-conditioner compressor.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.10
• /
• pp.1065-1072
• /
• 2008

A HDD adopts a sensorless brushless DC (BLDC) motor as a spindle motor. Because there is no direct sensor measuring rotor position. open loop commutations with inductive sensing are used to increase the rotor speed up to a certain speed where the zero crossings of the back electromotive force (EMF) voltage are measurable. Therefore, successful open loop commutations are necessary for the stable start-up control of the spindle motors. In this paper, the time scale and the number of the open loop commutations are employed for design parameters to guarantee robustness to torque constant variation and initial rotor position. The design results are verified by experiments on a very low current start-up of the spindle motor with various environment. The experimental results show that the design results can decrease the start-up failure rate considerably.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.646-650
• /
• 2004

This paper presents a novel method to detect the rotor position of the BrushLess DC(BLDC) motor at standstill and a start-up method to accelerate the rotor up to a certain speed where the conventional position sensorless control methods based on the back EMF could work reasonably The proposed initial rotor position estimation method is suitable to avoid the temporary reverse rotation or the starting failure. This method can be implemented using only one current sensor at DC link of the inverter. It does not depend on the model of the motor , and it is robust to motor parameter variations. By the proposed method, it is demonstrated experimentally that a stable starting can be achieved even with severe mechanical disturbance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.109-116
• /
• 2005

The high performance drives of the slotless Permanent Magnet Brushless DC(PM BLDC) motor can be achieved by the current control, where the currents flow according to the rotor position and the current phase is suitably controlled according to the operational condition. Rotor position information can be provided by Hall-IC or sensorless algorithm. So, the Hall-ICs are set up in this motor to detect the main flux from the rotor. Instead of using three Hall-ICs and encoder, this paper uses only two Hall-ICs for the permanent magnet rotor position and the speed feedback signals, and uses a micro-controller of 16-bit type (80C196KC). Also because of low resolution obtained by using Hall-IC even low-cost and simple structure, to improve the wide range of speed response characteristic more exactly, we propose the rotor position signal synthesizer using PLL circuit based on two Hall-ICs.