• Journal of the Korean Ceramic Society
• /
• v.32 no.7
• /
• pp.817-824
• /
• 1995

TiB2 was simultaneously synthesized and densified with concurrent self-propagating high-temperature synthesis and direct contact-heating by electrcial power input and pressure. Density of TiB2 synthesized by self-propagating high-temperature synthesis and consolidated simultaneously by direct contact-heating and pressure was maximum 80% of the theoretical density (4.52g/㎤). Temperature profile was analyzed by solving heat balance equation with numerical method (FTCS method). The temperature of the sample was sufficiently raised to that temperature sufficient to be densified. It was ascertained that the density of the SHS synthesized TiB2 is exponentially proportinal to the input thermal energy per mass.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1325-1326
• /
• 2006

Tungsten-molydiside $W_xMo_{1-x}Si_2$ was synthesized by self-propagating high temperature synthesis (SHS). The SHS product with the initial composition of (0.5Mo+0.5W+2Si) contains 23.9% $MoSi_2$, 40.89% $WSi_2$ with remaining 9.11% Mo, 9.16% Si and 16.94%W. Lattice parameters of the $MoSi_2$ and $WSi_2$ determined by Rietvelt analysis were a=0.3206 nm, c=0.7841 nm and a=0.3212 nm, c=0.7822 nm, respectively.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.268-269
• /
• 2006

Preparation processing of sintered silicon nitride ceramics was emphatically investigated with Self-Propagating High-Temperature Synthesis (SHS) of silicon nitride prepared by ourselves as raw material. The results indicate that good sinter ability can be obtained with cheaply SHS of silicon nitride preparing silicon nitride materials. The cost of silicon nitride materials will be lowered.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.931-937
• /
• 1995

AlN powder and whiskers were synthesized by direct nitridation of aluminum powder in pure nitrogen atmosphere. The nitridation reaction of aluminum powder was initiated by heating the sample to the ignition temperature and the reaction was finished in less than 3 minutes. AlN whisker-shaped morphology was observed predominantly when the sample was heated above 90$0^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.620-623
• /
• 2001

The peculiarities of using Self-propagating High-temperature Synthesis (SHS) and solid state phase synthesis for production of high temperature superconductor materials are discussed. Oxide superconductors with general formula $ReBa_2$$Cu_3$$O_{7-x}$ (Re= Y, Yb, Sm, Nd) have been made with using barium oxide initial powder instead of traditional barium carbonate. X-ray powder diffraction showed a single phase orthorhombic perovskite structure was produced in all reactions. Phenomena observed during the grinding of the reactant mixture are presented. Mechano-chemical activation - as a pretreatment of the reactant mixture - strongly influences the kinetic parameters, the reaction mechanism, and the composition and structure of the final product.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1283-1292
• /
• 1994

Ultra-fine $\beta$-SiC powders were fabricated by self-propagating high temperature synthesis process (SHS) using chemical furnace. The dependences of the C powders with different surface areas, the molar ratios of C/Si, the weight ratios of chemical fuel content, and pellet diameter-size on synthesis were investigated. Compositional and structural characterization of these powders was carried out by scanning electron micrograph and X-ray diffraction. The $\beta$-SiC powders which had C/Si mole ratio=1.05, 3 times chemical fuel contents, and pellet diameter=20 mm were optimum for synthesis efficiency. By optimizing process-variables, it is possible to fabricate $\beta$-SiC powders which have little secondary phases ($\alpha$-SiC).

• Composites Research
• /
• v.33 no.5
• /
• pp.256-261
• /
• 2020

In this study, the ignition temperature of the Al-Ti-C reaction system, the microstructure and the mechanical properties of the TiC/Mg composite which produced by the self-propagating high-temperature synthesis (SHS) followed by stir casting process were investigated. Mg based composite with uniformly dispersed 0, 10, 20, and 30 vol.% TiC were fabricated, and higher volume fraction of TiC reinforced composite showed superior compressive strength and wear resistance as compared with Mg matrix. It is attributed to the less contamination, defects, impurities in TiC/Mg composite by the in-situ SHS yield effective load transfer from the matrix to the reinforcement.

• Applied Microscopy
• /
• v.26 no.3
• /
• pp.379-388
• /
• 1996

Structure of premartensite in $Ti_{50}Ni_{49}Fe_1\;and\;Ti_{50}Ni_{50}$ prepared by self-propagating high temperature synthesis (SHS) method has been investigated by a detailed transmission electron microscopy. $Ti_{50}Ni_{49}Fe_1$ consists of microdomain area and needle type domain area. On the other hand, $Ti_{50}Ni_{50}$ consists of microdomain-free and microdomain area, and needle type domain area. Various types of extra superreflections, such as 1/2<100>, 1/2<110> and 1/4<210> type superreflection have been observed in the selected area electron diffractions from microdomain area. Such extra superreflections are due to transformation from B2 structure to distorted B2 structure or premartensite. The present study shows that incommensurate phase forms as an intermediate phase during martensitic transformation. Particularly, in Fe-free $Ti_{50}Ni_{50}$, two types of matrix phases have been observed, microdomain and microdomain-free area. Types of extra superreflections in $Ti_{50}Ni_{50}$ are different from those in $Ti_{50}Ni_{49}Fe_1$, i.e. 1/7<321> type superreflections have been observed, instead of 1/2<110>, 1/2<100>, 1/4<210> types in $Ti_{50}Ni_{49}Fe_1$.

• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.29-35
• /
• 2010

We produced cylindrical porous TiNi bodies by Self-propagating High-temperature Synthesis (SHS) process, varying the heating schedule prior to ignition of a loose preform compact made from (Ti+Ni) powder mixture. To investigate the effect of the heating schedule on the behaviour of combustion wave propagation and the structure of porous TiNi shape-memory alloy (SMA) body, change of temperature in the compact during SHS process was measured as a function of time and used for determining combustion temperature and combustion wave velocity. Microstructure of produced porous TiNi SMA body was observed and the results were discussed with the combustion characteristics. From the results it was concluded that the final average pore size could be controlled either by the combustion wave velocity or by the average temperature of the preform compact prior to ignition.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.3
• /
• pp.275-280
• /
• 2002

The peculiarities of using Self-propagating High-temperature Synthesis (SHS) and solid-stave chase synthesis for production of high temperature superconductor materials were discussed. Oxide superconductors with general formula of $ReBa_2Cu_3O_{7-x}$ (Re=Y, Sm) haute been made by using barium oxide initial powder instead of traditional barium carbonate. Phenomena observed during the grinding of the reactants mixture are presented. Mechano-chemical activation - as a pre-treatment of the reactants mixture - strongly influences the kinetic parameters, the reaction mechanism, and the composition and structure of the final product.