• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.1
• /
• pp.45-51
• /
• 1989

In metal cutting various types of chips are produced in consequence of cutting conditions. According to the type of chips the cutting mechanism is to be changed. Most of the cutting theory is based on the continuous chip because of its convenient analysis, but the occurrence of the saw-toothed chip depends upon the workpiece and/or the cutting conditions, one of which is titanium alloy used widely. Nowadays titanium alloys are used widely with the rapid development of aerospace structural engineering application, whereas the theory of cutting mechanism has not been established yet, and the formatting process has not been understood satisfactorily, either. Unfortunately several misconceptions, conflicting statements and statements needing further clarifi- cation are also found. In this paper an attempt is made to clarify the formation process of saw-toothed chips which are to be produced during the orthogonal cutting process of titanium alloys. They were machined at low speed to avoid the rapid tool wear. We observed the SEM-photographs of chips taken at the quick-st- opping device. It is hoped that a rational model of the mechanics of cyclic chip formation can be developed. The results obtained are as follows. 1. When a saw- toothed chip is formed, the shear band begins at the primary shear zone and trans- fers to the free surface, so that a segment is produced and it is completed by upsetting between the formatting segment and the formatted segment. 2. As the rake angle or the clearance angle increases in the machining of the titanium alloy, the chip approaches to that of the continous type. 3. When the rake angle and the clearance angle are increased the shear energy and the unit friction energy decrease, which shows the same aspect as that of the continuous chip.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.1
• /
• pp.29-39
• /
• 2007

This study were obtained elapsed time phase-by-phases, displacement, user angle, velocity and angular velocity to analyse kinematically contributing factors at impact of forehand drive motion, on targeting three male players. The results of the study were presented as follows; In the forehand drive swing, the elapsed time by phases was a total of .52 seconds: .30 seconds from backswing to impact and .22 seconds from impact to follow-through, Considering the mean change in locations of COM of each(part$\rightarrow$body segment) at impact, racket head, left shoulder, right wrist and left hip, the left-right directions(X-axis) were showm to be each $.61{\pm}.03$, $1.19{\pm}.08$, $.66{\pm}.03$, $.94{\pm}.06$, and $.45{\pm}.03m$. The displacement differences of COM of each body segment were shown to be -.57, -.05, -.33, and .16m. For the vertical direction(Z-axis), the center of mass was lowest at impact and highest at E3. For the displacement of the right wrist on the left hip, the right wrist moved to .82m to the lower direction without change in the locations of the hip from E1 from E2. When the left hip moved .02m from E2 to E3, the right wrist moved .7m in the upper direction. In respect to the velocity of each body segment, the hip and the shoulder joint accelerated and then the wrist followed. Then the right wrists of all the subjects and their racket heads showed maximum speed, and an effective swing was observed. At the angle of each part, the angle of the right wrist was the smallest at the backswing and the largest at the moment of the impact. Then it increased gradually in the follow-through section. In respect of angular velocity for subject A, the hip moved and the largest change occurred. Immediately before the impact, the subject made a swing using his right wrist, his hip, and the shoulder joint, showing the maximum value, which was judged to be effective.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.8
• /
• pp.796-804
• /
• 1992

This paper presents a design of a backbone network which uses a rigister-Insertion ring structure, The introduction of a high speed register in sertton backbone ring enables high performance inter-network 4ommunicatlons In a simple and modular structure at low cost and Its concurrent communications.. Two or more bridge nodes can be used to construct a register Insertion backbone ring network. The high bandwidth of the backbone ring sup ports heavy traffic for Inter-segment Eornrnunicatlons. The bridge node does both local address filtering to block data entering the ring and remote address filtering to block data entering the local LAN segment . Title local address greatly reduces the rate on the backbone ring and the remote address filterlng greatly reduces the traffic rate on each LAN segment. An feature makes the network the network reconflguratlon simpler and transparent to users. A throughput analysis Is used to deterrune the bandwidth of the backbone rlr)g transmission medium.

• World Technopolis Review
• /
• v.3 no.3
• /
• pp.139-152
• /
• 2014

The current transportation regime is largely based on two alternatives: (1) fixed route public transit, and (2) private ownership of internal combustion engine (ICE) powered vehicles per households. This paper analyzes one possible transportation alternative, Micro Electric Vehicles or MEVs, and compares with the ICE vehicles in terms of social, economic and environmental benefits, especially emphasizing its environmental advantage over ICE vehicles for future sustainability. While some representative models of MEVs exist in a limited market capacity, but global technical standards are generally insufficient and non-homogenous across nations, which restricts the development of the proposed transportation sector. The focus of this paper is to analyze the characteristics and potential benefits of MEVs in economical and environmental perspectives, including development status and technical standards, with a particular focus in the E.U., the U.S., Japan, and Korea. Based on the data of analysis, this paper aims to derive and propose a cooperative and adaptive global policy framework designed to speed up adoption and expansion of the global MEV market, including passenger and utility vehicles. We propose MEV to be a new mobility segment in the global transportation market because of their advantage in environmental impact, sustainability, overall cost of ownership, and safety.

• Design & Manufacturing
• /
• v.2 no.3
• /
• pp.32-39
• /
• 2008

after using dom die, this sheet pressed from a variation condition of size, of die holder power,of rpm speed, accordingly the kind of material, the conditionof deformation movement between both sheets is analyzed, is investigated in the Press machine. even if the change quantity which formed raises a blank holder pressure, the change quantity which is special is not visible from the segment where there is not a bead, the segment where there is a bead to the other side does change quantity schedule to initially and the features of press holding power which the change quantity diminishes is showed consequently from pressurization change quantity it is visible but until a rupture territory from the rpm, it goes but the features where the change quantity does not change a lot is observationd, from the CR2-sheet the quality comes out though well but a possibility of getting a result under same conditions of AL-sheet does not become the formation which stands is. It is like that though press-die which uses the drawing-sheet it exchanges the sheets, when AL-sheet with doing, the conclusion for maintain which have a formation sincerity healthy characteristic is same with afterwords.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.4
• /
• pp.201-207
• /
• 2001

This paper describes an automated detection algorithm of ST-T episodes using global curvature which can connect the isoelectric level in ECG and can eliminate not only the slope of ST segment, but also difference of the baseline and global curve. This above method of baseline correction is very faster than the classical baseline correction methods. The optimal values of parameters for baseline correction were found as the value having the highest detection rate of ST episode. The features as input of backpropagation Neural Network were extracted from the whole ST segment. The European ST-T database was used as training and test data. Finally, ST elevation, ST depression and normal ST were classified. The average ST episode sensitivity and predictivity were 85.42%, 80.29%, respectively. This result shows the high speed and reliability in ST episode detection. In conclusion, the proposed method showed the possibility in various applications for the Holter system.

• Journal of the Korea Society for Simulation
• /
• v.10 no.3
• /
• pp.47-58
• /
• 2001

Evaluation of Freeway Congestion Management Using Mesoscopic Traffic Simulator A mesoscopic simulation study to measure the effects of trip generation caused by rampant expansion of residential area around the Kyungbu corridor has been conducted. Some alternatives, which seem to be judgememtally plausible and technically feasible to mitigate such congestion, have been carefully examined and evaluated by the simulation model called INTEGRATION. Alternatives are mostly network improvements. Banpo IC dedicated ramp construction (A1), Seocho IC TSM based weaving elimination (A2), dedicated local and express separation over Seocho-Yangjae segment (A3), Heonleung IC (A4) and Daewang If installations (A5), Pangyo IC improvement (A6), Baikhyun IC (A7) and Dongbaek IC installations (A8) along with Shingal-Pangyo segment capacity addition (A9). The most capital intensive ones are A9, A5, and A4 in that order. A1, A6, A7, and A8 are short in distance but they are also capital intensive and need some construction periods. The least capital driven alternatives are h2 and A3, the h2 is easier to do, but A3 needs traffic diversion scheme during construction. The A1, A7, and A8 have been identified cost effective in terms of speed increase and travel time saving. Along with these results, some limitations and future research agenda regarding simulation have also been presented.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4625-4635
• /
• 2022

A low-energy dielectric loaded accelerator with a non-uniform, multi-segment structure is studied and optimized. So far, no analytical solution is provided for such structures. Also, due to the existing nonlinear behavior and a large number of geometric parameters, the problem of numerical optimizations is complex. For this reason, a method is presented to design and optimize such structures using the Genetic Algorithm (GA). Moreover, the GA output results are compared with Trust Region (TR) and Nelder-Mead Simplex (NMS) methods. Comparative results show that the GA is more efficient in achieving optimization goals and also has a higher speed than the two other methods. Finally, an optimized accelerating tube is integrated into a proper coupler. Then, the accelerator is simulated for full electromagnetic investigations using the CST suite of codes. This design leads to a structure with a power of about 80 kW in the X-band, which delivers electrons to the output energy in the range of 300-459 kV. The length and outer diameter of the accelerating tube obtained are 10 cm and 1 cm, respectively.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.75-82
• /
• 2012

Elimination of rotor position sensors mechanically coupled with the rotor shaft is attractive to variable speed drives primarily due to increased system reliability and cost reduction. In this regard, search for a simple and robust position sensorless control has been intensified in past few years specifically for low-cost, high-volume applications such as home appliances. This paper describes a new parameter insensitive position sensorless control for switched reluctance motor (SRM) drives satisfying such a need in this market segment. Two consecutive switch-on times of the controllable switch in hysteresis current control are compared to estimate the rotor position and speed. The proposed sensorless control algorithm is very simple to implement since it does not depend on extensive computation or any additional hardware. In addition, the proposed method is robust in that its dynamic performance is least affected by system parameter variations. The proposed approach is demonstrated on a single-controllable-switch-converter-driven SRM with two-phases that lends itself to a system with low cost and compact packaging which comes close to the intended applications. Analysis and simulation results followed by experimental verification are presented to demonstrate the feasibility of the proposed sensorless control method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.4
• /
• pp.79-86
• /
• 2007

The shape of excessive penetration mainly depends on welding conditions(welding current and welding voltage), and welding process(groove gap and welding speed). These conditions are the major affecting factors to width and height of back bead. In this paper, back-bead prediction and weldability estimation using artificial neural network were investigated. Results are as follows. 1) If groove gap, welding current, welding voltage and welding speed will be previously determined as a welding condition, width and height of back bead can be predicted by artificial neural network system without experimental measurement. 2) From the result applied to three weld quality levels(ISO 5817), both experimented measurement using vision sensor and predicted mean values by artificial neural network showed good agreement. 3) The width and height of back bead are proportional to groove gap, welding current and welding voltage, but welding speed. is not.