• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.3
• /
• pp.31-35
• /
• 2022

Recently, with the 4th industrial revolution, the demand for high-density semiconductors for large-capacity data processing is increasing. Researchers are interested in researching the reliability of surface mount technology (SMT). In this study, the effect of PCB pad design on assembly and adhesion reliability of passive component was analyzed using design of experiment (DOE). The DOE method was established using the pad length, width, and distance between pads of the PCB as variables. The assembly defect rate of the passive element after the reflow process was derived according to the misplacement direction of the chip resistor. The shear force between the passive element and the PCB was measured using shear tests. In addition, the shape of the solder according to the pad design was analyzed through cross-sectional analysis.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.5
• /
• pp.211-217
• /
• 2022

New buildings have been designed using different seismic design standards that have been revised. However, the seismic performance of existing buildings is evaluated through the same performance evaluation guidelines. Existing buildings may not satisfy the performance targets suggested in the current guidelines, but there are practical limitations to discriminating the existing buildings with poor seismic performance through a full investigation. In this regard, to classify buildings with poor seismic performance according to the applied standard, this study aimed to evaluate performance-based investigation of the seismic design proposals of buildings with different design standards. The target buildings were set as RC ordinary moment frames for office occupancy. Changes in seismic design criteria by period were analyzed, and the design spectrum changes of reinforced concrete ordinary moment resisting frames were compared to analyze the seismic load acting on the building during design. The seismic design plan was derived through structural analysis of the target model, compared the member force and cross-sectional performance, and a preliminary evaluation of the seismic performance was performed to analyze the performance level through DCR. As a result of the seismic performance analysis through the derived design, the reinforced concrete ordinary moment frame design based on AIK 2000 has an insufficient seismic performance level, so buildings built before 2005 are likely to need seismic reinforcement.

• Wind and Structures
• /
• v.35 no.4
• /
• pp.269-285
• /
• 2022

The pressure-mitigating effects of a high-speed train passing through a tunnel with a partially reduced cross-section are investigated via the numerical approach. A compressible, three-dimensional RNG k-ε turbulence model and a hybrid mesh strategy are adopted to reproduce that event, which is validated by the moving model test. Three step-like tunnel forms and two additional transitions at the tunnel junction are proposed and their aerodynamic performance is compared and scrutinized with a constant cross-sectional tunnel as the benchmark. The results show that the tunnel step is unrelated to the pressure mitigation effects since the case of a double-step tunnel has no advantage in comparison to a single-step tunnel, but the excavated volume is an essential matter. The pressure peaks are reduced at different levels along with the increase of the excavated earth volume and the peaks are either fitted with power or logarithmic function relationships. In addition, the Arc and Oblique-transitions have very limited gaps, and their pressure curves are identical to each other, whereas the Rec-transition leads to relatively lower pressure peaks in C_Pmax, C_Pmin, and ΔC_P, with 5.2%, 4.0%, and 4.1% relieved compared with Oblique-transition. This study could provide guidance for the design of the novel railway tunnel.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.7
• /
• pp.27-36
• /
• 2007

A model test was performed to evaluate the stability of a new earth retention system with a prestressed wale. For the model test, the dimensional analysis of a full-scaled earth retention system with prestressed wales was performed. Details of the dimensional analysis of the new earth retention system were presented in this paper. Based on the results of the dimensional analysis, the model-scaled earth retention system with a prestressed wale was simulated. The lateral earth pressures on the wall, the lateral deflection of the prestressed wale, the sectional force on members of the prestressed wale system, and the loads of struts were measured during construction simulation. The measured results were evaluated and compared with those of the design criterion. From the measurements, the behavior of this earth retention system was investigated.

• Geomechanics and Engineering
• /
• v.35 no.5
• /
• pp.487-497
• /
• 2023

Penetration rate (PR) and penetration depth (Pe) are crucial parameters for estimating the cost and time required in tunnel construction using tunnel boring machines (TBMs). This study focuses on investigating the impact of rock strength on PR and Pe through full-scale experiments. By conducting controlled tests on rock-like specimens, the study aims to understand the contributions of various ground parameters and machine-operating conditions to TBM excavation performance. An earth pressure balanced (EPB) TBM with a sectional diameter of 3.54 m was utilized in the experiments. The TBM excavated rocklike specimens with varying uniaxial compressive strength (UCS), while the thrust and cutterhead rotational speed were controlled. The results highlight the significance of the interplay between thrust, cutterhead speed, and rock strength (UCS) in determining Pe. In high UCS conditions exceeding 70 MPa, thrust plays a vital role in enhancing Pe as hard rock requires a greater thrust force for excavation. Conversely, in medium-to-low UCS conditions less than 50 MPa, thrust has a weak relationship with Pe, and Pe becomes directly proportional to the cutterhead rotational speed. Furthermore, a strong correlation was observed between Pe and cutterhead torque with a determination coefficient of 0.84. Based on these findings, a predictive model for Pe is proposed, incorporating thrust, TBM diameter, number of disc cutters, and UCS. This model offers a practical tool for estimating Pe in different excavation scenarios. The study presents unprecedented full-scale TBM excavation results, with well-controlled experiments, shedding light on the interplay between rock strength, TBM operational variables, and excavation performance. These insights are valuable for optimizing TBM excavation in grounds with varying strengths and operational conditions.

• Food Science of Animal Resources
• /
• v.44 no.5
• /
• pp.1181-1194
• /
• 2024

This study assessed and compared meat quality and fiber characteristics of longissimus lumborum (LL), psoas major (PM), and semimembranosus muscles among Hanwoo (HW), Jeju black (BL), and their crossbred (BH) cattle. Twelve carcasses from each breed (36 in total) were used in this study. BL and BH had higher moisture and crude ash contents and lower crude fat and protein contents than HW, regardless of the muscle type. BL had higher CIE a^*, cooking loss, and shear force values than did the other breeds for all muscle types. The muscle fiber size (cross-sectional area) of BL and BH was larger than that of HW for all muscle types. Type IIX was the dominant muscle fiber type in both BL and BH, regardless of muscle type; however, HW had the highest composition of type I compared to the other types (IIA, IIAX, and IIX) in PM. Higher total fiber density was observed in the LL and PM muscles of HW than in those of BL and BH. Meat quality and muscle fiber characteristics of BL and BH were distinct from those of HW.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.1 no.2
• /
• pp.17-29
• /
• 1997

Single-mode spectral analysis method is usually applied to a small-scale bridges with the simple geometric shape and uses only fundamental period to estimate the elastic earthquake forces and the displacements of the substructure. On the other hand, multi-mode spectral analysis method may be used instead if the possibilities of potential damage are developed when considering significance, scale, and geometric shape of briages. Since the dynamic responses of bridge can be significantly different depending on the modeling techniques for the restraint and support conditions etc, it may be misled to the unexpected results. In this study the dynamic analysis program which can model and analyze the bridge as a two- or three-dimensional framed structure is developed and verified with the results of other reliable program. Using this program together with the post processor, the designer can easily and readily obtain the reponses(moments, base shears, and displacements)of bridges necessary to design purpose. And further from the analysis results according to the variations of type, scale, and restraint and supprot conditions of bridges including sectional properties, applications of the effective and desirable seismic design are presented.

• Journal of the Korea Concrete Institute
• /
• v.24 no.6
• /
• pp.727-735
• /
• 2012

Recently, a high-strength strand of 2400 MPa was developed using domestic technologies. In 2011, KS D 7002 was revised to cover the newly developed high-strength strands to support their practical usage. Presently, however, discussions and evaluations are not sufficient on the mechanical properties of the strands and their performance in structural members. Also, there were no detailed reviews on the need to revise the current design code for practical use of the high-strength strands. In this study, flexural behavior of a member with the high-strength strands was estimated through sectional analysis and a review and comparison of the domestic and foreign design codes were conducted considering the analysis results. Also, the need for the revision of the design code was discussed. Such discussion especially focused on the estimation of the stress in strand, which related with various issues such as determination methods for yield point of strands, time-dependent loss of prestressing force, estimation of stress in strand at member failure, and net strain limit for ductile failure of member. The discussion revealed that some parts in the design code need a revision and the further studies are required.

• Journal of Preventive Medicine and Public Health
• /
• v.38 no.3
• /
• pp.291-297
• /
• 2005

Objectives : The effects of exercise on bone density have been found to be inconsistent in previous studies. We conducted a cross-sectional study in premenarcheal girls to test two hypotheses to explain these inconsistencies. Firstly,'the intensity of mechanical strain, in terms of the ground reaction force(GRF), has more important effects on the bone mass at a weight-bearing site', and secondly, 'calcium intake modifies the bone response to exercise'. Methods : The areal bone mineral density was measured at the Os calcis, using peripheral dual energy X-ray absorptiometry, in 91 premenarcheal girls aged between 9 and 12 years. The intensity of mechanical strain of exercise was assessed by a self-report questionnaire and scored by the GRF as multiples of body weight, irrespective of the frequency and duration of exercise. The energy and calcium intake were calculated from the 24-hour dietary recall. An analysis of covariance(ANCOVA) was used to determine the interaction and main effects of exercise and calcium on the bone density, after adjusting for age, weight, height and energy intake. Results : The difference in the bone density between moderate and low impact exercise was more pronounced in the high than low calcium intake group. The bone density for moderate impact exercise and high calcium intake was significantly higher than that for low impact exercise (p=0.046) and low calcium intake, after adjusting for age, weight, height and energy intake. Conclusions : Our study suggests that the bone density at a weight-bearing site is positively related to the intensity of mechanical loading exercise, and the calcium intake may modify the bone response to exercise at the loaded site in premenarcheal girls.

• Journal of Korea Water Resources Association
• /
• v.44 no.2
• /
• pp.157-167
• /
• 2011

A numerical model was developed to predict the stage-discharge curve and lateral distribution of unit discharge in open channels with nonuniform cross section or compound open-channels. The governing equation is the one-dimensional momentum equation based on assumptions of the steady and uniform flow conditions in the longitudinal direction and the uniform water surface elevation in a cross section. Vegetative drag force term was included in governing equation in order to reflect the effect of floodplain vegetation on the flow characteristics. Finite element method was applied to obtain the numerical solution of the governing equation. Stage-discharge curve and lateral distribution of unit discharge for a given water surface are calculated based on input data, such as the cross sectional geometry, Manning's roughness coefficient, vegetative information and longitudinal slope of channel bed. The developed model was verified by comparing the calculated results with the observed data and the results of Darby and Thorne's(1996) model and the nonlinear k-$\epsilon$ model. The verified model was applied to estimate the upstream boundary conditions in two-dimensional flow model. The numerical results using laterally distributed unit discharge were compared with those obtained using uniformly distributed unit discharge in two-dimensional flow model.