• 대한안전경영과학회지
• /
• 제13권4호
• /
• pp.213-223
• /
• 2011

Recent cross-country competition and Chinese steel industry because of the emerging steel industry in Korea is a very difficult situation. Therefore, the steel industry in order to overcome this difficult market environment, the quality, cost competitiveness, enhance customer service levels and enhance international competitiveness through is needed. In this study, the purpose of strengthening the competitiveness of steel companies in order and hit the recovery of raw materials have been developed to optimize the model, developed before and after the results were analyzed. In addition, when applied to other products in order to minimize risk and optimize cutting trial stage of development details of the model is presented in detail. Therefore, the developed model was applied to order the recovery of raw materials hits and significantly improved production planning time has been shortened dramatically. In the present study the contents of other products when properly applied and the competitiveness of companies to improve customer service levels are expected to be helpful.

• 한국지진공학회논문집
• /
• 제5권4호
• /
• pp.83-95
• /
• 2001

내진상세가 적용되지 않은 철근콘크리트 교각의 거동특성 및 내진성능을 살펴보기 위해서 축소교각모형실험을 수행하였다. 횡방향 철근이 심부를 구속할 만큼 충분히 배근되어 있지 않은 중심 원형 단면의 실교각을 대상으로 기초 상단의 소성 힌지 부위에서 겹침이음이 된 주철근을 사용했을 때와 연속철근을 사용했을 경우로 구분되도록 철근상세를 결정하였다. 이에 따라 3기의 축소교각시험체를 제작하여 수직방향 축하중을 가한 상태에서 준정적 반복하중을 재하하는 실험을 수행하였다. 실험결과를 통해서 겹침이음이 있는 교각시험체는 연성거동을 하지 않지만, 겹침이음이 없이 연속철근을 사용한 교각시험체는 어느 정도의 한정연성거동을 하는 것으로 분석되었다.

• Geomechanics and Engineering
• /
• 제15권2호
• /
• pp.775-781
• /
• 2018

Shake table tests were conducted on scaled tunnel model to investigate the mechanism and effect of seismic loadings on horseshoe scaled tunnel model in ground fissure site. Key technical details of the experimental test were set up, including similarity relations, boundary conditions, sensor layout, modelling methods were presented. Synthetic waves and El Centro waves were adopted as the input earthquake waves. Results measured from hanging wall and foot wall were compared and analyzed. It is found that the seismic loadings increased the subsidence of hanging wall and lead to the appearance and propagation of cracks. The values of acceleration, earth pressure and strain were greater in the hanging wall than those in the foot wall. The tunnel exhibited the greatest earth pressure on right and left arches, however, the earth pressure on the crown of arch is the second largest and the inverted arch has the least earth pressure in the same tunnel section. Therefore, the effect of the hanging wall on the seismic performance of metro tunnel in earth fissure ground should be considered in the seismic design.

• Structural Engineering and Mechanics
• /
• 제12권5호
• /
• pp.559-572
• /
• 2001

A numerical model, in the form of a computer program, for evaluating the fire resistance of insulated wide-flange steel columns is presented. The three stages associated with the thermal and structural analysis in the calculation of fire resistance of columns is explained. The use of the computer program for tracing the response of an insulated steel column from the initial pre-loading stage to collapse, due to fire, is demonstrated. The validity of the numerical model used in the program is established by comparing the predictions from the computer program with results from full-scale fire tests. Details of fire tests carried out on wide-flange steel columns protected with ceramic fibre insulation, together with results, are presented. The computer program can be used to evaluate the fire resistance of protected wide-flange steel columns for any value of the significant parameters, such as load, section dimensions, column length, type of insulation, and thickness of insulation without the necessity of testing.

• Steel and Composite Structures
• /
• 제46권6호
• /
• pp.773-791
• /
• 2023

Connections with damage concentrated to pre-selected components can enhance seismic resilience for moment resisting frames. These pre-selected components always yield early to dissipate energy, and their energy dissipation mechanisms vary from one to another, depending on their position in the connection, geometry configuration details, and mechanical characteristics. This paper presents behaviour insights on two types of beam-to-beam connections that the angles were designed as energy dissipation components, through the results of experimental study and finite element analysis. Firstly, an experimental programme was reviewed, and key responses concerning the working mechanism of the connections were presented, including strain distribution at the critical section, section force responses of essential components, and initial stiffness of test specimens. Subsequently, finite element models of three specimens were established to further interpret their behaviour and response that were not observable in the tests. The moment and shear force transfer paths of the composite connections were clarified through the test results and finite element analysis. It was observed that the bending moment is mainly resisted by axial forces from the components, and the dominant axial force is from the bottom angles; the shear force at the critical section is primarily taken by the slab and the components near the top flange. Lastly, based on the insights on the load transfer path of the composite connections, preliminary design recommendations are proposed. In particular, a resistance requirement, quantified by a moment capacity ratio, was placed on the connections. Design models and equations were also developed for predicting the yield moment resistance and the shear resistance of the connections. A flexible beam model was proposed to quantify the shear resistance of essential components.

• 콘크리트학회논문집
• /
• 제16권6호
• /
• pp.867-873
• /
• 2004

It has been known that debonding failures between CFS(Carbon Fiber Sheet) and concrete in the strengthened RC beams are initiated by the peeling of the sheets in the region of combined large moment and shear forces, being accompanied by the large shear deformation after flexural cracks. These shear deformation effects are seldom occurred in small-scale model tests, but debondings due to the large shear deformation effects are often observed in a full-scale model tests. The premature debonding failure of CFS, therefore, must be avoided to confirm the design strength of full-scale RC beam in strengthening designs. The reinforcing details, so- called 'U-Shape fiber wrap at mid-span' which wrapped the RC flexural members around the webs and tension face at critical section with CFS additionally, were proposed in this study to prevent the debonding of CFS. Other reinforcing detail, so called 'U-Shape fiber wrap at beam end' were included in this tests and comparisons were made between them.

• 한국산학기술학회논문지
• /
• 제17권10호
• /
• pp.54-60
• /
• 2016

BIM은 단일모델을 이용해 다양한 시나리오로 활용 가능하다는 이점이 있다. BIM 모델을 통해 2D 도면을 자동으로 추출하는 점도 그 중의 하나이나, 이를 실무에서 그대로 활용하기에는 현실적으로 어려움이 따른다. 건축 상세도면은 실내재료 마감 및 복잡한 시공방법을 표현할 뿐 아니라 공사비 산정에 있어 매우 중요한 요소이다. 하지만 이를 BIM 환경에서 표현하는 공통적인 규칙이나 약속이 없고, 설계사별로 같은 의미의 상세도면을 각기 다른 형태로 보유하고 있어 건설산업차원에서의 정보공유 및 교환을 어렵게 한다. 따라서 본 연구에서는 건축 상세도면의 BIM 활용을 위해 부분상세 정보를 체계화하는 방법을 제시하고, BIM 라이브러리와 어떻게 연계되어 수량 및 공사비 산정의 기초자료로 활용되는지 파악한다. 본 연구는 건축 설계자가 설계 업무 진행시 BIM 라이브러리를 통하여 부분상세정보를 확인하고 단가정보, 자재정보 등과 연계되어 수량 및 공사비를 산출하는데 활용될 수 있다. 또한 BIM 라이브러리-기술콘텐츠 연계기술로 인해 BIM기반의 설계효율과 프로세스를 개선해 중소설계사무소의 효율적인 BIM 활용에 도움이 될 것이다.

• Ocean Systems Engineering
• /
• 제3권1호
• /
• pp.35-53
• /
• 2013

In this study, a hybrid floating structure with cylinder was introduced to reduce the hydrodynamic motions of the pontoon type. The hybrid floating structure is composed of cylinders and semi-opened side sections to penetrate the wave impact energy. In order to exactly investigate the hydrodynamic motions and structural behavior of the hybrid floating structure under the wave loadings, integrated analysis of hydrodynamic and structural behavior were carried out on the hybrid floating structure. Firstly, the hydrodynamic analyses were performed on the hybrid and pontoon models. Then, the wave-induced hydrodynamic pressures resulting from hydrodynamic analysis were directly mapped to the structural analysis model. And, finally, the structural analyses were carried out on the hybrid and pontoon models. As a result of this study, it was learned that the hybrid model of this study was showed to have more favorable hydrodynamic motions than the pontoon model. The surge motion was indicated even smaller motion at all over wave periods from 4.0 to 10.0 sec, and the heave and pitch motions indicated smaller motions beyond its wave period of 6.5 sec. However, the hybrid model was shown more unfavorable structural behavior than the pontoon model. High concentrated stress occurred at the bottom slab of the bow and stern part where the cylinder wall was connected to the bottom slab. Also, the hybrid model behaved with the elastic body motion due to weak stiffness of floating body and caused a large stress variation at the pure slab section between the cylinder walls. Hence, in order to overcome these problems, some alternatives which could be easily obtained from the simple modification of structural details were proposed.

• 한국재난관리표준학회지
• /
• 제3권1호
• /
• pp.33-42
• /
• 2010

본 논문에서는 전체해석과 국부해석 조합방법을 이용하여 국부손상 또는 균열의 영향을 반영한 트러스교의 전체지간에서의 응력거동을 예측하였다. 이를 위해서 전체 구조체는 프레임요소에 의한 해석을 수행하고 국부 상세부분은 쉘요소에 의한 해석을 수행하여 두 결과를 조합함으로써 교량의 연결부처럼 응력분포가 복잡한 부분에서 이동하중에 따른 응력이력을 손쉽게 산정하게 된다. 트러스 연결부의 실제 기하학적 형상 및 강성을 전체 프레임해석에 고려하기 위해 국부 쉘모델과 프레임모델의 변위 비교를 통해 프레임 모델의 단면수정계수를 산정하였으며, 실제 공용중인 트러스교의 실험값과 해석값을 비교하여 전체해석-국부해석 조합방법을 검증하였으며, 더 나아가 국부손상의 영향이 반영된 국부 쉘모델 해석결과를 전체해석에 반영시켰다.

• 콘크리트학회논문집
• /
• 제15권2호
• /
• pp.263-272
• /
• 2003

내진상세가 적용되지 않은 RC중공구형단면 교각의 지진 시 거동특성 및 내진성능을 파악하기 위하여 축소모델 실험을 수행하였다. 축소모델은 교각의 소성힌지영역내에 동일한 위치에서 모든 주철근이 겹침이음된 모델과 연속된 철근을 사용하여 겹침이음을 없앤 모델로 설계하였다. 실험은 축력이 재하된 상태에서 준정적 반복하중을 재하하였다. 실험결과 겸침이음모델은 주철근의 겹침이음부에서의 부착파괴가 발생하였지만 비교적 큰 연성거동을 나타냈으며 연속철근을 사용한 모델은 전형적인 휨파괴 특성과 매우 큰 연성거동을 보였다.