• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.129-138
• /
• 2006

In this study, we identified the secondary precipitates from Samsan-jeil and Sambong mine, Goseong, Gyeongnam by means of scanning electron microscopy, electron probe microanalysis and X-ray powder diffraction analysis. Copper sulfide minerals had been produced from the mines during last few decades, however they are not worked. White and blue precipitates were found at the downstream of mine rock dump at Sambong mine and green one was at Samsan-jeil mine. The white precipitate covered the host rock surface with thickness of $30{\mu}m$, and is a kind of diatom with $10{\mu}m$ in length and $3{\mu}m$ in width. It is a species Fragilaria constuens, which is contained a order Pennales(pennate diatom) and lives in fresh water. The blue precipitate is the alteration product of chalcopyrite. It resultes in the increase in the ratio Cu:Fe from 5 to 13. The green precipitate has worm-like morphology with $10{\sim}20nm$ in diameter and $200{\sim}300nm$ in length. It is mainly composed of secondary copper sulfate such as woodwardite. However, it could be formed by the activity of microorganism, because the copper content is more than any secondary copper sulfate reported in copper sulfide mine. In order to identity the green precipitate exactly, the further research is needed.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.445-449
• /
• 2000

Nickel ferrite $(Ni_{0.75}Fe_{2.25}O_4$ was synthesized by co-precipitation method in order to investigate its behavior under conditions of the reactor coolant system in pressurized light water nuclear power plants. Ammonia or potassium carbonate was used as a solution pH control agent, and aqueous ammonia or potassium carbonate solution or secondary distilled water was used as a co-precipitate washing agent. The effects of the pH control agent and the co-precipitate washing agent on the production yield on the basis of the Ni/Fe molar ratio and the particle characteristics of final products were investigated by XRD, SEM, EDX and XPS. The production yield was almost congruent with that of the initial aqueous mixture in case of using potassium carbonate as a pH control agent, while in case of using ammonia, it was quite changed. The difference seemed to be due to the effects of $Ni^{2+}{\leftarrow}NH_3$complexation in the aqueous solution and of the pH of co-precipitate washing agent.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.2
• /
• pp.139-151
• /
• 2009

Mineralogical characteristics of secondary precipitate formed at some mineral water springs in Gyeongbuk Province, Korea were studied in relation to water chemistry. The chemical water types of mineral water springs are mostly classified as $Ca-HCO_3$ type, but $Na(Ca)-HCO_3$ and $Ca-SO_4$ types are also recognized. Ca, Fe, and $HCO_3\;^-$ are the most abundant components in the water. The pH values of most springs lie in 5.76${\sim}$6.81, except Hwangsu spring having pH 2.8. Saturation indices show that all springs are supersaturated with respect to iron minerals and oxyhydroxides such as hematite and goethite. The result of particle size analysis shows that the precipitate is composed of the composite with various sizes, indicating the presence of iron minerals susceptible to a phase transition at varying water chemistry or the mixtures consisting of various mineral species. The particle size of the reddish precipitate is larger than that of the yellow brown precipitate. Based on XRD and SEM analyses, the precipitate is mostly composed of ferrihydrite (two-line type), goethite, schwertmannite, and calcite, with lesser silicates and manganese minerals. The most abundant mineral fanned at springs is ferrihydrite whose crystals are $0.1{\sim}2\;{\mu}m$ with an average of $0.5\;{\mu}m$ in size, characterized by a spherical form. It should be interestingly noted that schwertmannite forms at Hwangsu spring whose pH is very low. At Shinchon spring, Gallionella ferruginea, one of the iron bacteria, is commonly found as an indicator of the important microbial activity ascribed to the formation of iron minerals because very fine iron oxides with a spherical form are closely distributed on surfaces of the bacteria. A genetic relationship between the water chemistry and the formation of the secondary precipitate from mineral water springs was discussed.

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.230-235
• /
• 2015

Crystallographic models are effective tools to interpret, calculate and even to predict the preferred crystallographic morphologies of precipitates in various precipitation systems. The present study gives an introduction on the recently developed secondary constrained coincident site lattice (II-CCSL) model. Using the II-CCSL model, the interface matching condition of the ${\beta}-Mg_{17}Al_{12}$ precipitates with ${\alpha}-Mg$ matrix in an aged AZ91 alloy has been analyzed to rationalize the morphologies of the precipitates. The results show that the characteristic crystallographic features of the observed ${\beta}-Mg_{17}Al_{12}$ precipitates, i.e., the habit plane of the ${\beta}-Mg_{17}Al_{12}$ lath with a Burgers orientation relationship (OR) and the growth direction of the ${\beta}-Mg_{17}Al_{12}$ with a Crawley OR exhibit a better lattice matching degree than their vicinal orientations. Moreover, the Crawley OR is preferred to the Burgers OR due to a better lattice match.

• Resources Recycling
• /
• v.10 no.5
• /
• pp.8-15
• /
• 2001

Aluminum dross should be recycled in consideration of characteristics of the dross and its reutilization after processing. In this study, aluminum dross generated in the domestic secondary aluminum industry was processed to use it as raw material for producing aluminum hydroxide. Sample dross was classified according to its size. The dross smaller than $850\mu$m was leached with sodium hydroxide solution to extract the remaining aluminum from the dross into the solution, and then aluminum hydroxide precipitate was recovered (rom the leach liquor. Purity of the obtained aluminum hydroxide was above 98% and size of the sample was in range of $\3~39mu$m. Recovery of aluminum hydroxide precipitate was highest on condition that A/C ratio of the solution was 0.5 and pulp density was 14~16% at the leaching step. From the result, it was suggested that this process could be applicable to recycling of aluminum dross.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.12-19
• /
• 2016

The <100> oriented $Fe_{83}Ga_{17}$ alloys with various contents of NbC or B were prepared by directionally solidification method at the growth rate of $720mm{\cdot}h^{-1}$. With a small amount of precipitates, the columnar grains grew with cellular mode during directional solidification process, while like-dendrite mode of grains growth was observed in the alloys with higher contents of 0.5 at% due to the dragging effect of precipitates on the boundaries. The NbC precipitates disperse both inside grains and along the boundaries of $Fe_{83}Ga_{17}$ alloys with NbC addition, and the Fe2B secondary phase particles preferentially distribute along the grain boundaries in B-doped alloys. Precipitates could affect grain growth and improved the <100> orientation during directional solidification process. Small amount of precipitate element addition slightly increased the magnetostrictive strain, and a high value of 335 ppm under pre-stress of 15 MPa was achieved in the alloys with 0.1 at% NbC. Despite the fact that the effect on magnetic induction density of small amount of precipitates could be negligible, the coercivity markedly increased with addition of precipitate element for $Fe_{83}Ga_{17}$ alloy due to the retarded domain motion resulted by precipitates.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.202-208
• /
• 2001

Aluminum dross should be recycled in consideration of characteristics of the dross and its reutilization after processing. In this study, aluminum dross generated in the domestic secondary aluminum industry was processed to use it as raw material for producing aluminum hydroxide. Sample dross was classified according to its size. The dross smaller than 1mm was leached with sodium hydroxide solution to extract the remaining aluminum from the dross into the solution, and then aluminum hydroxide precipitate was recovered from the leach liquor. Purity of the obtained aluminum hydroxide was above 98 percent, and particle size of the sample was in range of 3-39${\mu}{\textrm}{m}$. From the result, it was suggested that this process could be applicable to recycling of aluminum dross.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.85-90
• /
• 2018

For the recovering rare earths in the spent nickel-metal hydride batteries, 10 M NaOH is added to the solution leached with sulfuric acid. The rare earth powders were precipitated at rate of 98 % at the condition of pH 2.0 or less. The recovered rare earth complex precipitate increased the leaching rate to nitric acid by heat treatment at $800^{\circ}C$ for 4 hours. Subsequently secondary precipitation was performed by adding oxalic acid to the solution in which the rare earth complex precipitate was dissolved. The re-precipitated rare earth powders were converted into oxide form through heat treatment at $800^{\circ}C$ for 4 hours with purity of 99.5 %.

• Resources Recycling
• /
• v.29 no.5
• /
• pp.28-37
• /
• 2020

In this study, the effect of precipitation temperature, ammonium chloride amount and addition method, vanadium and sodium hydroxide content of the solution on the precipitation of ammonium metavanadate were examined by using the sodium vanadate(NaVO₃) solution in alkali region as a starting material. As the pH of solution decreased, the addition amount of ammonium chloride and the vanadium content of the solution increased, the precipitation rate of ammonium metavanadate increased. In this research condition, the basic conditions for obtaining more than 90% of precipitation yield were 10,000mg/L of vanadium content, 2equivalents of ammonium chloride addition, room temperature, and 2 hours of precipitation time. The size of precipitated particles decreased with increasing precipitation rate. Especially when liquid ammonium chloride was injected into the solution, the precipitation rate was the slowest and the particle size of the precipitate was the largest. After the primary precipitation by adding ammonium chloride as a solid, the secondary precipitation was carried out by adding new reactants. At this time, the precipitation with added ammonium chloride solid was not affected by the precipitates present in the solution. However, when liquid ammonium chloride was added, new precipitate was deposited on the surface of the precipitate present in the solution, increasing its size. Due to the difference in ammonium metavanadate solubility to temperature, the precipitation temperature at the vanadium content of 10,000mg/L in the solution affected the precipitation rate of ammonium metavanadate and the precipitation temperature did not affect the precipitation rate at a high concentration of more than 30,000mg/L vanadium content in the solution.

• Resources Recycling
• /
• v.12 no.3
• /
• pp.46-53
• /
• 2003

Recycling of aluminum dross is an important issue in the secondary aluminum industries. In this study, aluminum dross generated in the domestic secondary aluminum industry was processed to use it as raw material for producing alumina refractories. Sample dross was classified according to its size. The dross smaller than 1 mm was leached with sodium hydroxide solution to extract the remained aluminum from the dross into the solution. and then aluminum hydroxide precipitate was recovered from the leach liquor. The waste residue in the leaching was washed, dried and roasted. Most remained metallic components in the residue was changed into oxide through the processes. The roasted dross was made into alumina castable refractories by mixing with aggregates and a binder. Bending strength of the tested castable specimen was over $25\;kg/\textrm{m}^2$ and compressive strength over $80\;kg/\textrm{cm}^2$, which satisfied the Korean Standard value respectively. From the results, it was suggested that this process could be applicable to recycling of aluminum dross.