• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.234-235
• /
• 2017

The bonding of the asphalt-based waterproof sheet is carried out in such a manner that the sheet and the sheet are adhered together and the lower adhesive layer of one sheet is adhered to the upper film layer of the other sheet, and the asphalt layer and the PE or HDPE film layer are bonded. When the joints are formed in the form of junctions between heterogeneous materials and exposed to the concrete joint movements and other deteriorating factors, the integrity of the joints can deteriorate and problems such as lifting and peeling off of the joints can occur. Therefore, this study was carried out to prevent unstable joint adhesion of the asphalt compound and film layer and to prevent defects in the adhesion between self - adhesive waterproof sheets. The self-adhesive waterproof sheet of this study can maximize bond stability by inducing bond between asphalt compounds during sheet-to-sheet bonding, thereby improving bonding strength.

• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.13-18
• /
• 2013

Slider bearing is a widely used load-carrying element in the industry. While a large number of studies have investigated the effect of overall surface curvature, very few have considered sinusoidal surface. Recently, consideration of surface roughness/waviness or intentional wave design has been identified as an important issue in the manufacture of hard disk driver, mechanical seal, hydraulic machine, and etc. This study investigated the load-carrying capacity of a finite-width slider bearing with a wavy surface. Film thickness ratios, length-width ratio, ambient pressure, amplitude, and partial distribution were selected as the simulation parameters. The calculation results showed that the load-carrying capacity rapidly varied at small film thickness ratio, but the waviness near the area of minimum film thickness made much more influence with an increase in film thickness ratio. As the length-width ratio of bearing was increased, ambient pressure became more influential at small film thickness ratios. Furthermore a particular partial distribution of the wavy area led to higher load-carrying capacity than did the whole distribution. Consequently, the results of this study are expected to be of use in surface micro-machining of finite-width slider bearings.

• Food Science and Industry
• /
• v.50 no.2
• /
• pp.12-26
• /
• 2017

Processing steps such as washing and cutting, involved in preparing fresh-cut produce causes tissue damage, leading to rapid quality deterioration. Major defects of fresh-cut produce are discoloration, softening, off-odor development, and microbial growth. Packaging of fresh-cut produce has been changed to reduce these quality problems. Flexible packaging film is widely used to pack fresh-cut produce. Vacuum packaging was the popular packaging method in the beginning of fresh-cut industry in Korea. Vacuum packaging creates high $CO_2$ and low $O_2$ levels to control browning of fresh-cut produce. However, these conditions induce some visual defects and off-odor development. Discoloration problem was also found when fresh-cut produce was packaged with conventional packaging film or plastic tray. Modified atmosphere (MA) packaging is effective for prolonging shelf-life of fresh-cut produce by decreasing $O_2$ and increasing $CO_2$ concentration in the package. Retail MA packaging using different oxygen transmission rate (OTR) film and micro-perforated film has started to be applied to fresh-cut produce in Korea. Proper MA package design that provides optimum range of $O_2$ and $CO_2$ partial pressures is one of the major challenges in the industry. An initial package flushing with $N_2$ or an low $O_2$/high $CO_2$ atmosphere is also used to more rapidly establish steady-state MA condition. Film OTR and $O_2$ flushing affects the fermentative volatile production, off-odor development, electrolyte leakage, discoloration, $CO_2$ injury, microbial population of fresh-cut produce. There is also a demand for convenient packaging to attract consumers. Rigid fresh-cut produce container for retail market has increased since the packaging provides excellent protection from physical damage during transport. Rigid tray used as actual serving vessel for the consumer is increasing in Korea. The tray with flexible lid to wrap or seal fresh-cut produce is more and more gaining popularity. Further practical technology to control quality change and microbial growth for each fresh-cut product has been studied since various fresh-cut items were required. The fresh-cut industry also focuses on searching for more convenient and environmentally friendly packaging.

• Korean Journal of Food Science and Technology
• /
• v.43 no.3
• /
• pp.321-328
• /
• 2011

Edible films were developed from jujube (Zizyphus jujube Miller) using depolymerization processes of ultrasound and high-pressure homogenization. A 4.6% (w/w) jujube hydrocolloid was treated by ultrasound (600W, 20 min) or homogenized at high pressure (172 MPa, 6 s) and mixed with whey protein isolate, glycerol, xanthan, and sucrose esters of fatty acids to form film-forming solutions from which films were formed by drying. The film prepared by highpressure homogenization (HPH film) produced more homogeneous films without particles than those prepared without depolymerization or with the ultrasound treatment. HPH films possessed the highest tensile strength (4.7MPa), the lowest water vapor permeability ($2.9g{\cdot}mm/kPa{\cdot}h{\cdot}m^2$), and the most uniform and dense microstructures among the films. Flavor profiles of jujube powder and the films were distinguishable. Heat seal strength and oxygen permeability of the HPH films were 44.4 N/m and $0.025mL{\cdot}{\mu}m/m^2$/day/Pa, respectively. Antioxidant activities of jujube power and HPH films were not significantly different.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.5
• /
• pp.69-74
• /
• 2011

This paper deals with the detail rotordynamic analysis for the vertical rotor system as development of vertical sea water lift pump for FPSO deep well. In a vertical rotor system, since linearized stiffness and damping coefficients of fluid film bearing are no longer be valid, hence the transient response analysis considering a fluid film force for every journal position in the bearing needs to be required. In this study, the transient response analysis of the proposed vertical pump rotor system was carried out in dry-run and wet-run conditions, respectively. The results show that orbital vibration responses of the rotor system remain stable at rated speed and thereby operating reliability of the vertical rotor system is confirmed. To overcome complexity of calculation pr ocedure and time consuming calculation of transient analysis, the calculating technique of steady-state response analysis is also proposed. The results of steady-state response obtained by applying the proposed technique to the rotor system are good agreement with the reference results, that is, transient responses.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.8
• /
• pp.1085-1096
• /
• 2000

An experimental study was performed to examine the heat and mass transfer characteristics of $LiBr-H_2O$ solution flowing over a single horizontal tube with the water vapor absorption. Effects of the flow rate and the temperature of the solution at the top of the tube, the absorber pressure and the drainage pattern were considered. The absorption rate depends highly on the absorber pressure at the low flow rate condition while on the solution inlet temperature at the high flow rate condition. Also, when the flow rate is low, the absorption performance with the sheet flow drainage appeared to be higher than that with the dripping/jet drainage. However, at the high flow rate condition, the case became reversed. The liquid film became wavy with the higher absorption rate. The waves were more probable to form with the lower flow rate and temperature of the solution, and with the higher absorber pressure.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.3
• /
• pp.15-20
• /
• 2013

The graphites as airtight structure seals prevent high-pressure and high-temperature gas from flowing into actuator of propulsion system and generate lubricant film during wear procedure to assist lubricant and sealing. In this study, the tribological characteristics of the graphite in high-temperature are evaluated. In order to evaluate the tribological characteristics of high density graphite(HK-6), variables which are temperature, sliding speed and contact load are set. this study suggest optimized environment conditions through the wear properties of graphite. Consequeantly, high temperature is better than at room temperature to generate lubricant film, so that friction coefficient of graphite is lower at high temperature than at room temperature.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.3
• /
• pp.7-13
• /
• 2011

In Korea, the car mobile phone service had started in 1961 and with this Korea Mobile Telecommunications Services was established in 1984. Its service was mainly focused on the mobile phone service for the car which led the popularity of the full-scale mobile phone service. There are many kinds of materials, colors and patterns which are the elements of surface coating techniques. In light of that, we are focused on the UV coating that is ranked as an important part of the techniques in this study. In the first, the use of various materials for the cellular phone and surface processing techniques for the cellular phone were searched. On the basis of the results, the experiments of actual consumer experience with the exfoliation of the surface were done and through that we proposed the best way of processing the surface for the cellular phone and the materials. The result of the Wear Test showed that thick coating was detached more slowly and each company differed in their results with UV paints despite the same thickness of UV coating. The seal (UV) exfoliation of cellular phone is deeply related with the film thickness and the film formation when the users use the cellular phones and the exfoliation of the cellular phone surface will be decreased if the manufacturers meet the best conditions for the cellular phone.

• Food Science and Preservation
• /
• v.6 no.1
• /
• pp.11-15
• /
• 1999

Grapes (large seed strains)were treated with fumigation using SO\ulcorner and seal-packaged by PE film, then storage at 0$^{\circ}C$ at 90$^{\circ}C$ RH for the test of storage life. The fruits weight loss and abnormal fruits increased with storage. The abnormal fruits were rapidly produced after 80 days, however, these rates of Rubel muscat and Shingyoku were only 8.0 and 8.3%, respectively. After 90 days, the rate of Rubel muscat was 19.1%, resulting in the least rate. Moisture content of Kaiji and Honey black slightly increased and that of other grapes decreased. Soluble solids content and acidity decreased except Shingyoku and Honey black, however, sugar/acid ratio increased with these strains. The external appearances were depressed with storage but sensory test value of Shingyoku, Honey black, Rubel muscat were ranged from 7 to 9, showing good evaluation. The hardness of Honey black after 90 days resulted in the highest value 0.51 and that of Izunishiki and Kaiji were 0.23-0.25, showing the least value.

• The Journal of Korean Academy of Prosthodontics
• /
• v.9 no.1
• /
• pp.79-83
• /
• 1969

1) 가능(可能)한한 조직(組織)이 변형(變形)되지 않아야 한다. 2) Atmospheric pressure를 이용(利用)하기 위(爲)하여 peripheral border 에 있어서의 조직변형(組織變形)이 필요(必要)한 경과(境過)는 그 정도(程度)가 eiastic force가 retentive force 보다 크지 않도록 최소한(最小限)으로 해야 한다. 3) Denture base와 조직(組織)의 원형간(原形間)에는 접촉(接觸)이 밀접(密接)해야 한다. 그래야 saliva의 film 균일(均一)하고 얇게 될 수 있다. 4) Atmospheric pressure는 denture의 retention과 중요(重要)한 연관성이 있으므로 physiologic seal area를 형성(形成)해 주는 것이 유리(有利)하다. 5) Ridge의 형태(形態)도 denture의 retention 대(對)한 하나의 중요(重要)한 인자(因子)이다. 6) Denture에 의(依)해서 피개(被蓋)되는 면적(面積)은 retention에 관계(關係)되는 한 인자(因子)로써 피개면적(被蓋面積)이 클수록 유지력(維持力)이 커진다. 7) Saliva의 viscosity도 retention의 한 인자(因子)가 된다. 8) Friction은 retention의 한 인자(因子)가 될수는 있으나 병인적(病因的)인 증상(症狀)을 유발(誘發)할수 있으므로 이용(利用)해서는 않된다.