• Journal of the Korean Wood Science and Technology
• /
• 제13권3호
• /
• pp.49-53
• /
• 1985

The effects of pre-treatments, the hot water extraction of wood meal and the addition of chemical ($CaCl_2$) to wood-cement water system on the properties of wood-cement composite such as modulus of rupture (MOR), modulus of elasticity (MOE), water sorption ratio and swelling ratio of resulting boards were studied in this experiment. The wood meals through 0.83mm(20 mesh) and retained on 0.42mm(35 mesh) screen were prepared from Pinus densiflora S. at Z. and Larix leptolepsis G. For hot water extraction, 500 grams of wood meal for each species were heated to boiling with 1,500ml of distilled water in 2-liter beaker for 6 hours. Every 2 hours, the wood meals were washed with boiling distil1ed water and reheated to boiling again. After 6 hours boiling, the boiled wood particles were collected by pouring this particles on 200 mesh screen. The collected particles then washed twice with hot distilled water and dried for 24 hours in an oven at $109{\pm}20^{\circ}C$. A mixture of 663.4 grams of cement with 331.7 grams of wood meal based on oven-dry weight were dry-mixed in a plastic vessel. The mixture was kneaded with 497.6ml of distilled water in the ratio of 1.5ml of water to a gram of wood meal. To add calcium chloride to the mixture as an accelerator, $CaCl_2$ 4% solution by weight per volume, was added to pine-or larch-cement board in the ratio of 3% to cement weight. To set wood-cement board, this mixture was clamped at 30cm ${\times}$ 30cm, in thickness of 1.5cm for 3 days at room temperature, declamped and then placed at open condition for 17 days. The target density was 1.0. The four specimens sized to 5cm in width and 28cm in length were used for MOR and MOE test for each treatment. After MOR test, the tested specimens were cut to the size of 5cm ${\times}$ 5cm for water sorption and swelling test. The twenty specimens used to measure the water sorption ratio (soaking 24 hours) and ten of these were used for swelling ratio measurement The results obtained were as follows: 1) Larch was not suitable for wood-cement boards because larch-cement board developed no strength, but pine showed 97.9kg/$cm^2$ by hot water extraction. 2) To increase MOR, hot water extraction was more effective than the addition of $CaCl_2$ in pine and larch because the $CaCl_2$ addition was seemed to speed up the ratio of cement hydration without reacting with the wood substances. 3) The water sorption ratio was lowered by the addition of $CaCl_2$ to wood-cement system because the chemical additive accelerated the rate of cement hydration. 4) In pine-cement board, the swelling ratio from 0.37 to 0.42 percent was observed in length and the swelling ratio from 0.88 to 2.0 percent in thickness. As a rule, the swelling ratio of wood-cement board was very low and the swelling ratio in thickness was higher than in length.

• 한국통신학회논문지
• /
• 제42권4호
• /
• pp.716-722
• /
• 2017

본 논문에서는 은 나노 분말과 카본 잉크를 이용하여 13.56 MHz에서 동작하는 완전 인쇄형 NFC 태그를 설계 및 제작하였다. 제안된 NFC 태그는 50 pF의 내부 커패시턴스를 갖는 NFC 태그 IC에 적용하기 위해서, $2.74{\mu}H$의 인덕턴스를 갖는 원형 코일을 PI 필름 위에 설계하였으며, 전통적인 회로 제작 방식인 PCB 제조 공정에 비해 대면적 및 대량 생산, 저비용, 친환경공정 등의 장점을 가진 인쇄 전자 기술인 스크린 프린팅 기법을 이용하여 제작하였다. 제안된 구조는 단일 층으로 구현된 원형 코일, 코일 외곽과 중심부 사이에 칩 실장을 위한 점퍼 패턴, 그리고 코일과 점퍼 패턴과의 절연을 위한 절연 패턴으로 구성되어 있으며, 은 나노 분말과 카본 잉크를 이용하여 전도성 패턴과 절연 패턴을 중첩 인쇄하여 구현하였다. 본 논문에서 제안된 NFC 태그의 성능 검증을 위해 인쇄선폭, 두께, 선저항, 밀착력 그리고 환경 신뢰성 평가 등을 수행하였으며, 완전 인쇄형 제작 방식 기반 NFC 태그의 적합성을 확인하였다.

• 청정기술
• /
• 제19권4호
• /
• pp.410-415
• /
• 2013

폴리이미드(polyimide) 필름 위에 은(Ag) 나노 페이스트(paste)가 인쇄된 집전체 및 활성탄소(activated carbon)를 이용하여 제조한 페이스트와 5% potassium polyacrylate (PAAK) 겔(gel) 전해질을 이용하여 슈퍼캐패시터(supercapacitor) 반쪽전지(half cell)를 제작하였다. 집전체 및 전극은 스크린 인쇄를 이용하여 제작하였으며 인쇄된 집전체의 두께는 $7.3{\mu}m$이고 면저항은 $5{\sim}7m{\Omega}/square$이다. 전극 페이스트는 비표면적 $1,968m^2/g$인 활성탄소이고 도전재는 카본 블랙(carbon black)을 사용하였으며 바인더로는 poly (4-vinylphenol)를 7:1:3 비율로 혼합하고 2-(2-buthoxyethoxy) 에틸아세테이트(BCA)를 주 용매로 사용하여 제조하였다. 전기화학적 분석을 위해 순환-전압 전류법(cyclic voltammetry)을 이용하여 전기화학적 특성과 안정도를 평가하였으며 순환-전압전류법 측정을 위한 인가 전압의 범위는 -0.5 V~0.5 V이고 주사속도(scan rate)의 범위는 10~500 mV/s로 하였다. 제작된 슈퍼캐패시터 반쪽전지의 비축전 용량은 주사속도가 10 mV/s, 500 mV/s일 때 각각 44.04 F/g, 8.62 F/g이었다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제20권2호
• /
• pp.49-55
• /
• 1997

This study was carried out to investigate radiographical and operating conditions of X-ray units and exposure doses to patients during chest radiography, so that the results could provide basic data used for reducing the exposure dose and for providing the diagnostic information with better quality. The conditions and exposure doses of 100 X-ray units mainly used for chest radiography were examined and also 100 radiological technologists mainly handling those apparatus at 76 medical facilities in Pusan were surveyed using a questionnaire from October 1 to December 31 in 1995. The following results were obtained from the study : 1. It was found that most units were capable of taking a high tube voltage radiography by showing 67% of the units equipped with the maximum tube voltage of 150 kV, 94% with more than 500 mA for the rating capacity and 85% with the full wave type of a signal phase. 2. For actual chest radiographical conditions, however, 80% of the units were operated at $60{\sim}100\;kVp$ and only 14% at 100 kVp and over for the high tube voltage. 3. The average exposure time was less than 0.1 second, and eighty four percent of the units adapted the X-ray tube currents ranging from 200 to 300 mA, 80% the focus-film distances between 180 and 210 cm, and 63% the focus sizes of more than 2.0 mm. 4. Most units(98%) employed additional filters made of aluminum, 75% the thickness of filters less than 2.0 mm, and only 2 units the compound filters. 5. Ortho chromatic system was only adopted in 13% of screen film system for the units, and 73% used the grid ratio at 8 : 1 for the low tube voltage during chest radiography. 6. The average exposure dose of all X-ray units during chest radiography was $371\;{\mu}Sv$ with a difference of about 16 times between the minimum to the maximum, and $386\;{\mu}Sv$ both at hospitals and at health centers, followed by $380\;{\mu}Sv$ at general hospitals and $263\;{\mu}Sv$ at university hospitals without showing any statistically significant differences. In conclusion, since patients during chest radiography at medical facilities in Pusan exposed to high levels of radiation, it is recommended that appropriate added filters and grids necessary for the high tube voltage radiography and high-speed screen systems should be adopted and used as soon as possible in order to reduce exposure dose to the patients.

• Design & Manufacturing
• /
• 제11권1호
• /
• pp.1-6
• /
• 2017

In these days, due to generalization of using smart mobile phone and wearable device such as smart watch, demand of Cover-glass and touch screen panel for protecting display increases. With increasing the demand of Cover-glass, slimming technique is promising for weight lightening, zero bezel. Cover-glass produced by this technique is required to decreasing thickness with increase strength. In the Cover-glass manufacturing process, mechanical processing and chemical processing has improve in the strength. Generally, Diamond electrodeposition wheel is used in mechanical process. Reinforced glass with the characteristics of the brittle and high hardness was manufactured by using a diamond electrodeposition wheel. At this time, Because of surface of the tool present non-uniform distribution of diamond particle, it has generate Loading of wheel and it has been decrease life of grinding tool, efficiency of grinding, quality and shape accuracy of workpiece. Thus Research is needed to controling particle distribution of diamond electrodeposition wheel uniformly. And it is necessary to study micro hole machining such as proximity senser hole, speaker hole positioned Cover-glass. Reinforced glass with the characteristics of the brittle and high hardness is difficult to machining. Processing of reinforced glass have generated wear of tool, micro cracks. Also, it is decreasing shape accuracy. In this paper, We conducted a study on how to control particle distribution uniformly about the diamond tool manufactured using elecetodeposition processing. It analyzed the factors that affect the arrangement of the particles in the electrodeposition process by design of experiment. And There is produced the grinding tool, which derives an optimum deposition conditions, for processing Cover-glass edge and the machinability was evaluated.

• 한국세라믹학회지
• /
• 제42권2호
• /
• pp.117-122
• /
• 2005

나노 코팅 기술로써 빠른 증착 속도와 미세구조 제어가 용이하여 항공기 엔진 부품 열차폐 코팅으로 널리 이용되는 Electron Beam Physical Vapor Deposition (EB-PVD)세라믹 코팅 기술을 연료전지 전해질 제조에 적용하였다. EB-PVD 법을 이용하여 NiO-YSZ 기판에 YSZ 전해질을 약 10$\mu$m의 두께로 짧은 시간에 코팅하였으며 증착온도에 따라 나노 구조의 표면을 가진 YSZ 막을 얻을 수 있었다. 연료전지 전해질로서의 특성을 평가하기 위하여, 같은 조건의 코팅으로 $Al_{2}O_3$기판에 전해질을 동일한 조건으로 코팅하여 전해질의 전기적 특성을 평가하였다. 또한 양극물질로서 $LaSrCoO_3$ 분말을 일반적인 스크린 프린팅 기법으로 코팅하여 EB-PVD의 코팅을 이용한 고체산화물 연료전지 제조 가능성에 대하여 논의하였다

• Transactions on Electrical and Electronic Materials
• /
• 제18권5호
• /
• pp.261-264
• /
• 2017

$Ni_{0.79}Co_{0.15-x}Cu_xMn_{2.06}O_4$ ($0{\leq}x{\leq}0.09$) thick films were fabricated using the conventional solid-state reaction method and screen-printing method. Structural and electrical properties of specimens based on the amount of Cu were observed in order to investigate their applicability in the infrared detector. All specimens showed a single spinel phase with a homogeneous cubic structure. As the amount of Cu increased, the average grain size increased and was found to be approximately $5.01{\mu}m$ for the $Ni_{0.79}Co_{0.06}Cu_{0.09}Mn_{2.06}O_4$ specimen. The thickness of all specimens was approximately $55{\sim}56{\mu}m$. As Cu content increased, the resistivity and TCR properties at room temperature decreased, and these values for the $Ni_{0.79}Co_{0.06}Cu_{0.09}Mn_{2.06}O_4$ specimen were $502{\Omega}-cm$ and $-3.32%/^{\circ}C$, respectively. The responsivity and noise properties decreased with an increase in Cu content, with the specimen with a Cu content of x=0.09 showing 0.0183 V/W and $5.21{\times}10^{-5}V$, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1246-1247
• /
• 2008

With recent advanced in portable electric devices, wireless sensor, MEMS and bio-Mechanics device, the new typed power supply, not conventional battery but self-powered energy source is needed. Particularly, the system that harvests from their environments are interests for use in self powered devices. For very low powered devices, environmental energy may be enough to use power source. Therefore, in other to made piezoelectric energy harvesting device, PMN-PZT thick film was formed by the screen printing method on the Ag/Pd coated alumina substrate. The layer was 8 layers and slurry where a-terpineol, ethycellulose, ferro B-75001 as Vehicle, PMN-PZT powder used are fabricated by ball mill. The output power quality was be also investigated by changing the load resistance, weight and frequency. The made piezoelectric energy harvesting device was resulted from the conditions of 33$k{\Omega}$, 0.25g, 197Hz respectively. The thick film was prepared at the condition of 2.75Vrms, and its power was 230${\mu} W$ and its thickness was 56${mu}m$. The piezoelectric energy harvesting device output voltage was increased, when the load weight, load resistance was increasing and resonance frequency was diminishing. The other side, resonance frequency was diminished, when the weight was increasing. And output power was continuously it changed by load resistance, output voltage, weight and resonance frequency.

• Advances in materials Research
• /
• 제2권3호
• /
• pp.133-140
• /
• 2013

This paper aims to focus on the microwave processing of thick films which is a fast, cheap technique and could be the alternative to the currently used conventional high temperature processing technique. Microwave processing has gained worldwide acceptance as a novel method for heating and sintering a variety of materials, as it offers specific advantages in terms of speed, energy efficiency, process simplicity, finer microstructures and lower environmental hazards. Silver conducting thick films were prepared and processed in the household microwave oven. The films sintered at different time period by keeping the other parameter such as microwave power, film thickness etc constant. The microstructure analysis revealed that the surface morphology of the microwave processed films become compact with respect to the processing time. The sheet resistance for microwave sintered silver films is in the range of 0.003 to $1.207{\Omega}/{\Box}$ where as the films fired at 750 and $850^{\circ}C$ showed the resistance of 0.009 and $0.003{\Omega}/{\Box}$ which can be comparable. The results revealed that the microstructure of the microwave sintered films has more uniform and compact surface than that of the conventionally fired films. The paper reports upon the preparation of silver thick film by screen printing technique and processing the same by microwave which also compared with the conventionally processed thick films.

• 복식문화연구
• /
• 제25권4호
• /
• pp.448-457
• /
• 2017

This study aims to analyze the changes in the mechanical properties of interlock fabrics knitted with three types of fibers (i.e., cotton, wool, and polyester) by bonding fusible interlinings with varying deniers (i.e., 10D, 20D, and 30D) for a 3D virtual try-on system. We experimented with four properties and thicknesses of twelve specimens of interlining bonded knitted fabrics including face fabrics and interlinings. The results showed that the tensile property changed values (i.e., LT increased, and WT and RT decreased) according to the denier of interlinings; however, the change was slight. On the other hand, the bending property increased significantly as the denier of the interlining increased on both the wale and the course. Among shearing properties, the value of G increased as the denier of the interlining increased on both the wale and the weft; however, 2HG decreased. Additionally, changes in the compression property varied according to the fibers and the denier of the interlinings. The thickness of the knitted fabrics increased or decreased slightly by bonding the interlining. based on these results, we conclude that the 3D virtual system users need to reflect these numerical changes of interlock fabrics by bonding interlinings when they perform fitting tasks on the screen to accurately express the to accurately express the manufacturing conditions of the real garment.