• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 춘계학술대회
• /
• pp.666-667
• /
• 2015

스쿨존 시스템에서는 여러 상황을 구성하여 상황인식을 수행할 수 있다. 이렇게 인식된 상황들은 적절한 형태의 출력 양식을 통하여 해당 이벤트에 대한 결과를 알리게 된다. 본 논문에서는 스쿨존 시스템에서 상황 출력에 대한 설계 방안을 제안한다.

• Structural Engineering and Mechanics
• /
• 제48권2호
• /
• pp.221-239
• /
• 2013

This paper focuses on a development of strut-and-tie model (STM) to predict the capacity of an improved longitudinal joint for decked bulb-tee bridge systems. Nine reinforced concrete beam/slab specimens anchored by spliced headed bars with different details were tested. Test results were evaluated and compared with an anticipation of the validated STM. The proposed STM provides a lower bound of the ultimate capacity of the joint zone. It shows that the lap length of headed bars has a significant effect on structural behaviors of the improved joint. To develop a full strength joint, the range of the lap length can be determined by the strength and compatibility requirement. Design recommendations to spliced headed bars, concrete strength, as well as lacer bars in the joint zone are proposed for developing a full strength joint.

• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.183-189
• /
• 2013

In this paper, we propose a capacity modeling method for Bluetooth based LBSs (Location Based Services) between Bluetooth APs(Access Points) and mobile phones. In order to do this, we consider the entrance and exit of the users to and from the AP. Using parameters such as the connection time, data transmission time and number of users in the AP zone, we analyze the capacity of a Bluetooth AP using an appropriate queuing model. The required number of APs in a certain zone is estimated from the number of users in the zone using the proposed queuing model. By performing simulations and experiments, the validity and applicability of the proposed method are verified.

• Wind and Structures
• /
• 제31권3호
• /
• pp.197-207
• /
• 2020

Knowledge on the design value of extreme wind pressure coefficients (EWPC) of a specific zone of buildings is essential for the wind-resistant capacity of claddings. This paper presents a method to estimate the representative EWPC introducing the multivariate extreme value model. The spatial correlations of the extreme wind pressures at different locations can be consider through the multivariate extreme value. The moving average method is also adopted in this method, so that the measured point pressure can be converted to wind pressure of an area. The proposed method is applied to wind tunnel test results of a large flat roof building. Comparison with existing methods shows that it can give a good estimation for all target zones with different sizes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 기술교육전문연구회
• /
• pp.12-15
• /
• 2003

The YBaCuO thick film was deposited by the electrophoresis in the solution with different dimension particles. The morphology of the films deposited from different particles size was compared. The powder made by sol-gel method has the submicron particles, which deposit the most smooth film, and without microcracks after sintering. After sintering of the deposited film, the zone-melting process was carried out in low oxygen partial pressure (100 Pa) and Ag was used as substrate. And the zone-melted YBaCuO was studied by XRD.

• Journal of Electrical Engineering and Technology
• /
• 제9권4호
• /
• pp.1324-1331
• /
• 2014

This paper proposes a compensation PWM technique for the extension of output voltage ranges in three-phase VSI applications using three shunt resistors. The proposed technique aims to solve the dead zone, which occurs in high modulation indexes. In the dead zone, two phase currents cannot be sampled correctly, so that the three-phase VSI cannot be operated up to the maximum output voltage. The dead zone is analyzed in detail, and the compensation PWM algorithm is developed. The proposed algorithm is verified by numerical analysis and experimental results.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2012년도 춘계학술발표대회
• /
• pp.989-992
• /
• 2012

본 논문에서는 안전한 공장 원격제어를 위한 시스템 프레임 워크를 제안한다. 공장기계와 IT의 융합으로 기술 발전함에 따라 공장 제어 시스템을 공장내부에서는 무선 제어시스템, 공장 외부에서는 원격 시스템의 필요성이 대두되어 많은 연구들이 진행되고 있다. 기존의 공장 자동화 시스템 SCADA(Supervisory Control And Data Acquisition)는 생산 공정 및 플랜트의 상태를 감시하고 제어하기 위한 목적으로 개발되었지만 원격제어 관련 내용이 부족하다. 공장 내부 보안을 위한 표준으로 ISA99 Security Standards에서도 통합 공정 제어 Zone & Conduits 방식 제시 공장의 각 영역을 Zone으로 나누고 허가된 사용자만 Conduit를 통해 다른 Zone의 노드와 통신을 하는 방식을 제안하였다. 하지만, 전체적인 프레임워크는 정의를 하고 있으나 외부 원격 제어 내용 부족하다. 따라서 본 논문에서는 스마트폰을 활용한 공장 외부에서의 안전한 원격 제어를 제공하는 통합관제시스템 프레임워크 구조를 제시하여 향후 관련 기술에 대한 기준점을 제시한다.

• Steel and Composite Structures
• /
• 제46권6호
• /
• pp.823-837
• /
• 2023

This paper presents the seismic performance of seven beam-column joints with an eccentricity between beam depths under cyclic loadings. The failure modes of the panel zone were divided into two types. One was the shear force failure that appeared in the entire panel zone (SFEPZ), the other was the shear force failure that appeared in the partial panel zone (SFPPZ). Seven finite element models were established using multi-scale methods. Compared with the experimental specimens, the hysteretic loops exhibited a similar trend. The multi-scale models could accurately simulate the experimental results. Furthermore, the calculation formulas of yield and plastic shear capacity of unequal-depth joints with outer annular stiffener were proposed.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.53-62
• /
• 2010

An airbag is composed of housing assembly, door assembly, cushion assembly, and an inflator. The inflator is the essential part that generates gas for airbag. When an airbag is activated, it effectively absorbs the crash energy of the passenger by inflating a cushion. In this study, tank tests were performed with newly synthesized propellants with various compositions, and the results are compared with the numerical results. In the simulation of inflator, a zonal model has been adopted which consisted of four zones of flow regions: combustion chamber, filter, gas plenum, and discharge tank. Each zone was described by the conservation equations with specified constitutive relations for gas. The pressure and temperature of each zone of the inflator were calculated and analyzed and the results were compared with the tank test data. In the zone of discharge tank the pressure quickly rose, the pattern of pressure curve was very similar to the pressure curve of real test. And in zone 1 & 2 & 3 the mass of products was increased and decreased with time. In zone 4, the mass of products was increased with time like real inflator. From the similarity of pressure curve in zone 4 and closed bomb calculation the modeled results are well correlated with the experimental values.

• 비파괴검사학회지
• /
• 제33권2호
• /
• pp.205-211
• /
• 2013

초음파 감쇠를 이용하여 티타늄 용접부에 대해 기계적 특성, 파단면 및 초음파특성을 연구하였다. 준비된 티타늄 시험편은 아르곤 가스를 이용하여 제작하였다. 티타늄 용접 시험편이 파단 되었을 때 변화하는 초음파 신호변화를 확인하기 위해서 인장시험을 실시하였다. 주사전자현미경을 이용하여 파단면을 관찰하고, 4 MHz 수직 탐촉자를 이용하여 초음파 시계열 신호를 획득하였다. 티타늄 판재에서 용접부는 모재부와 열영향부에 비하여 기계적 특성이 떨어지며 파단면분석을 통해 용접부의 입자크기가 모재부보다 큼을 확인할 수 있었다. RMS 신호 처리한 초음파 포락선의 면적과 인장강도의 상관관계를 나타내었다. 따라서 초음파를 이용하여 티타늄 용접부의 건전성 평가 방법이 유용함을 알 수 있었다.