• 폴리머
• /
• 제24권3호
• /
• pp.350-357
• /
• 2000

인쇄회로기판제조에 사용되는 glass/epoxy 프리프레그의 경화거동을 dielectrometer와 시차주사열분석기를 사용하여 연구하였다. 브롬화한 에폭시수지를 많이 포함하고 있는 본 프리프레그는 약 115$^{\circ}C$에서 가장 낮은 이온점도를 보였으며, 이 이후 경화반응의 진행과 함께 점도가 15$0^{\circ}C$까지는 상승하는 경향을 보여 주었다. 이것은 이 프리프레그의 경화반응이 115$^{\circ}C$ 부근에서 개시됨을 의미하며, 이 온도 이후부터 가속화된 분자간 가교화반응을 통해서 분자량이 현저히 커짐을 의미한다. 본 프리프레그의 dynamic scan에 따른 loss factor 및 tan $\delta$ 값을 측정하였다. 또한 실제 인쇄회로기판 제조에 사용하는 경화주기에 준하여 동일한 실험을 수행하여 그 거동을 비교하였다. 성형한 복합재료는 약30$0^{\circ}C$까지는 열적으로 안정한 것으로 나타났으며 이 온도 이후에서 급격한 열분해 반응이 진행되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.422.1-422.1
• /
• 2016

Graphene quantum dots (GQDs), a new kind of carbon-based photo luminescent nanomaterial from chemically modified graphene oxide (CMGO) or chemically modified graphene (CMG), has attracted extensive research attention in the last few years due to its outstanding chemical, optical and electrical properties. To further extended its potential applications as optoelectronic devices, solar cells, bio and bio-sensors and so on, intensive research efforts have been devoted to the CMG. However, the CMG, a suspension of aqueous, have problematic since they are prone to agglomeration after drying a solvent. In this study, we synthesized the GQDs from graphite and deposited on silicon substrate by kinetic spray. The photo luminescent properties of deposited GQD films were analyzed and compared with initial GQDs suspension. In addition, its carbon properties were investigated with GQDs solution properties. The properties of deposited GQD films by kinetic spray were similar to that of the GQDs suspension in water. We could provide a pathway for silicon-based silicon based device applications. Finally, the well-adjusted GQD films with photo luminescence effects will show Energy-Down-Shift layer effects on silicon solar cells. The GQD layers deposited at nozzle scan speeds of 40, 30, 20, and 10 mm/s were evaluated after they were used to fabricate crystalline-silicon solar cells; the results indicate that GQDs play an important role in increasing the optical absorptivity of the cells. The short-circuit current density (Jsc) was enhanced by about 2.94 % (0.9 mA/cm2) at 30 mm/s. Compared to a reference device without a GQD energy-down-shift layer, the PCE of p-type silicon solar cells was improved by 2.7% (0.4 percentage points).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 춘계학술대회 논문집
• /
• pp.79-84
• /
• 1993

This paper describes the development of lithium rechargeable cell. $LiCoO_2$ is recently recognized as a suitable cathode active material of a high voltage, high energy lithium rechargeable batteries because $Li^+$ ion can be electrochemically deintercalated/intercalated from/to $Li_xCoO_2$. The transition metal oxide of $LiCoO_2$ was investigated for using as a cathode active material of 4V class Li rechargeable cell. $LiCoO_2$ cathode was prepared by using a active material of 85 wt%, graphite powder of 12 wt% as a conductor and poly-vinylidene fluoride of 3 wt% as a binder. The electrochemical and charge/discharge properties of $LiCoO_2$ were investigated by cyclic voltammetry and galvanostatic charge/discharge. The open circuit voltage of prepared $LiCoO_2$ electrode exhibited approximately. potential range between 3.32V and 3.42V. During the galvanostatic charge/discharge, $LiCoO_2/Li$ cell showed stable cycling behavior at scan rate of 1mV/sec and potential range between 3.6V and 4.2V. Also its coulombic efficiency as function of cycling was 81%~102%. In this study the $LiCoO_2/Li$ cell showed the available discharge capacity of 90.1 mAh/g at current density of $1mA/cm^2$ and cell discharge voltage range between 3.6V~4.2V.

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.28-35
• /
• 2005

We propose a method to measure atrial arrhythmias (AA) such as atrial fibrillation (Afb) and atrial flutter (Afl) with a SQUID magnetocardiograph (MCG) system. To detect AA is one of challenging topics in MCG. As the AA generally have irregular rhythm and atrio-ventricular conduction, the MCG signal cannot be improved by QRS averaging; therefore a SQUID MCG system having a high SNR is required to measure informative atrial excitation with a single scan. In the case of Afb, diminished f waves are much smaller than normal P waves because the sources are usually located on the posterior wall of the heart. In this study, we utilize an MCG system measuring tangential field components, which is known to be more sensitive to a deeper current source. The average noise spectral density of the whole system in a magnetic shielded room was $10\;fT/{\surd}Hz(a)\;1\;Hz\;and\;5\;fT/{\surd}Hz\;(a)\;100\;Hz$. We measured the MCG signals of patients with chronic Afb and Afl. Before the AA measurement, the comparison between the measurements in supine and prone positions for P waves has been conducted and the experiment gave a result that the supine position is more suitable to measure the atrial excitation. Therefore, the AA was measured in subject's supine position. Clinical potential of AA measurement in MCG is to find an aspect of a reentry circuit and to localize the abnormal stimulation noninvasively. To give useful information about the abnormal excitation, we have developed a method, separative synthetic aperture magnetometry (sSAM). The basic idea of sSAM is to visualize current source distribution corresponding to the atrial excitation, which are separated from the ventricular excitation and the Gaussian sensor noises. By using sSAM, we localized the source of an Afl successfully.

• Restorative Dentistry and Endodontics
• /
• 제16권1호
• /
• pp.6-15
• /
• 1991

The purpose of this study was to observe in vitro chloride corrosion behavior from 5 kinds of amalgam (Caulk spheracal, Amalcap, Dispersalloy, Tytin, Sybralloy) as a function of time after tritruration by using potentiostat. After each amalgam alloy and Hg was triturated as the direction of the manufacturer by the mechanical amalgamator, the triturated mass was inserted the cyrindrical matal mold ($12{\times}10mm$) and was condensed by using routine manner. The specimen was removed from the mold and was stored at room temperature for 1 week, 1 month and 3 months, and standard surface preparation was routine carried out. The 0.9% saline solution was used as electrolyte in pH 6.8~7.0 at $30{\pm}0.5.^{\circ}C$. The open circuit potential was determined after 30 minutes' immersion of 1 week, 1 month and 3 month old specimens. The scan rate was 1 mV/sec and the surface area of amalgam exposed to the solution was $0.65\;Cm^2$ for each specimen. All potentials reported are with respect to a silver / silver chloride electrode (SSE). The following result was obtained. 1. All amalgam specimens became more noble corrosion potentials which represent the improved corrosion resistance as the time elapsed. 2. Three kinds of high copper amalgam always exhibited more noble potential than low copper amalgam at 1 week, 1 month and 3 months. 3. Two kinds of low copper amalgam had the similar polarization curve pattern with 3 current peaks at each time period and current densities associated with these peaks were decreased as aging especially in caulk spherical amalgam. 4. All kinds of high copper amalgam had the similar polarization curve pattern with absence of prominent current peak at each time period, but the polarization curve of D amalgam had one apparent current peak at 1 week.

• 재활복지공학회논문지
• /
• 제10권3호
• /
• pp.237-242
• /
• 2016

slip-ring 기술을 가진 spiral CT의 주요 장점으로는 X-ray 튜브의 연속적인 회전에 의해 환자에 대한 정보의 손실 없이 데이터를 연속적으로 획득할 수 있다는 것이다. 또한, X-선량의 인체 흡수의 감소를 위해서, 고시그널 저노이즈 및 빠른 데이터 획득 시간을 갖는 시스템이 요구되어 진다. 본 연구에서, CT 적용을 위해 다채널 포토센서 및 데이터 획득 시스템이 개발되어 졌다. 포토센서의 모듈은 16채널 CdWO4 크리스탈 및 실리콘 베이스의 포토다이오드가 사용되었다. 또한, 포토센서로 부터의 입력 신호에 대한 전기적인 증폭을 위해, 트랜스 임피던스 스위치 인테그레이터가 사용되었다. 스위치 인테그레이터는 CT 적용에 대해 적합한 시그널 밴드와 노이즈 퍼포먼스를 갖고 있다. 데이터 획득과 20 bit ADC 의 컨트롤은 FPGA를 이용하였고, 코딩은 VHDL을 사용하였다. CdWO4 기반의 실리콘 포토센서와 고SNR 및 좁은 시그널 밴드를 가진 증폭단 및 FPGA기반의 디지털 하드웨어는 CT적용 이외에 하드웨어 변경 없이 다른 분야에서도 이용 가능하다.

• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.423-446
• /
• 1993

Titanium and its alloys are finding increasing use in medical devices and dental implants. The strong selling point of titanium is its resistance to the highly corrosive body fluids in which an implant must survive. This corrosion resistance is due to a tenacious passive oxide or film which exists on the metal's surface and renders it passive. Potentiodynamic polarization measurement is one of the most commonly used electro-chemical methods that have been applied to measure corrosion rates. And the potentiodynamic polarization test supplies detailed information such as open circuit, rupture, and passivation potential. Furthermore, it indicates the passive range and sensitivity to pitting corrosion. This study was designed to compare the corrosion resistance of the commonly used dental implant materials such as CP Ti, Ti-6A1-4V, Co-Cr-Mo alloy, and 316L stainless steel. And the effects of galvanic couples between titanium and the dental alloys were assessed for their useful-ness-as. materials for superstructure. The working electrode is the specimen , the reference electrode is a saturated calomel electrode (SCE), and the counter electrode is made of carbon. In $N_2-saturated$ 0.9% NaCl solutions, the potential scanning was performed starting from -800mV (SCE) and the scan rate was 1 mV/sec. At least three different polarization measurements were carried out for each material on separate specimen. The galvanic corrosion measurements were conducted in the zero-shunt ammeter with an implant supraconstruction surface ratio of 1:1. The contact current density was recorded over a 24-hour period. The results were as follows : 1. In potential-time curve, all specimens became increasingly more noble after immersion in the test solution and reached between -70mV and 50mV (SCE) respectively after 12 hours. 2. The Ti and Ti alloy in the saline solution were most resistant to corrosion. They showed the typical passive behavior which was exhibited over the entire experimental range. Therefore no breakdown potentials were observed. 3. Comparing the rupture potentials, Ti and Ti alloy had the high(:st value (because their break-down potentials were not observed in this study potential range ) followed by Co-Cr-Mo alloy and stainless steel (316L). So , the corrosion resistance of titanium was cecellent, Co-Cr-Mo alloy slightly inferior and stainless steel (316L) much less. 4. The contact current density sinks faster than any other galvanic couple in the case of Ti/gold alloy. 5. Ag-Pd alloy coupled with Ti yielded high current density in the early stage. Furthermore, Ti became anodic. 6. Ti/Ni-Cr alloy showed a relatively high galvanic current and a tendency to increase.

• 한국전자파학회논문지
• /
• 제30권6호
• /
• pp.467-478
• /
• 2019

본 논문에서는 전자전용 재밍 송신기에 사용하기 위해서 개발된 광대역 평면형 능동위상배열 안테나 시스템의 설계 및 제작 그리고 측정 결과를 소개한다. 설계된 시스템은 $45^{\circ}$ slant 광대역 복사소자를 $8{\times}8$ 삼각 배열 구조로 배치하고, 광대역 GaN 반도체 고출력 증폭기와 GaAs 다기능집적회로(MFC)를 적용한 64개의 송신 채널을 구성하여 개발하였다. GaAs다기능집적회로는 광대역에서 빔 편이 현상을 피하기 위한 실시간 지연소자, 디지털 감쇠기 그리고 GaAs 구동증폭기를 포함하고 있어서 송신 빔 조향을 할 수 있으며, 시스템의 전자적 빔 조향 범위는 방위각/고각 방향으로 각각 ${\pm}45^{\circ}/{\pm}25^{\circ}$ 범위에서 가능하다. 개발된 시스템의 송신 빔 패턴 성능을 확인하기 위해 근접 전계 시험 시설을 이용하였다. 전자전용 송신 시스템 빔 패턴 측정 결과, 시스템의 유효방사출력은 목표성능(P) 대비 최대 9.8 dB 이상을 만족하였고, 방위각/고각 방향으로 각각 ${\pm}45^{\circ}/{\pm}25^{\circ}$ 빔 조향 결과 요구성능에 만족함을 확인하였다.