• Geomechanics and Engineering
• /
• v.14 no.2
• /
• pp.175-185
• /
• 2018

Sand Compaction Piles (SCPs) are constructed by feeding and compacting sand into soft clay ground. Sand piles have been installed with irregular cross-sectional shapes, and mixtures of both sand and clay, which violate the design requirement of circular shape according to the replacement area ratio due to various factors, including side flow pressure. Therefore, design assumptions cannot be satisfied according to the conditions of the ground and construction and the replacement area ratio. Two case histories were collected, examined, and interpreted in order to study the effect of the shape of SCPs. The effects of the distortion of SCP shape and the mixture of sand and clay were studied with the results of large direct shear tests. The design internal friction angle was secured with the irregular cross-sectional sand piles regardless of the replacement area ratio. The design internal friction angle was secured regardless of mixed condition when the mixture of sand and clay was higher than the replacement area ratio of 65%. Therefore, systematic construction management is recommended with a replacement area ratio below 65%.

• Archives of Pharmacal Research
• /
• v.26 no.9
• /
• pp.756-762
• /
• 2003

In the current study, our research focused on the estrogenic activity of isoflavonoids, mainly genistein, biochanin A and daidzein. Genistein enhanced the reporter gene expression of MCF-7-ERE-Luc cells, at a concentration as low as 10 nM, with a concentration of 100 nM the achieved gene expression effects were similar to those of 10 pM 17$\beta$-estradiol. Based on the estrogenic activities of biochanin A and daidzein, hydroxyl groups at the 4 and 5 positions are needed for the maximal effect of the genistein. The estrogenic effects of these isoflavonoids were inhibited by the concomitant treatment with tamoxifen. The data showed that the estrogenic effects of isoflavonoids were mediated through estrogen receptors. When the isoflavonoids were tested as mixtures, the estrogenic effects were lower than the arithmetic sum of those induced by each individual isoflavonoid. The estrogenic potency of each isoflavonoid was presented at EC50 levels with a 17$\beta$-estradiol equivalent concentration (EEQ) based on the dose response of each chemical. The EC50s and EEQs of genistein, biochanin A and daidzein were 4.15, 0.89 and 0.18 $\mu$M, and 15.0, 5.12 and 1.83 $\mu$ M/M, respectively. Our data clearly demonstrated that the pERE-luciferase reporter gene assay was suited for the sensitive and quantitative measurement, and large scale screening, of the estrogenicity of chemicals in vitro.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.19 no.2
• /
• pp.233-241
• /
• 2021

A series of three bench-scale experiments was performed to investigate the conversion of sodium metal to sodium chloride via reactions with non-metal and metal chlorides. Specifically, batches of molten sodium metal were separately contacted with ammonium chloride and ferrous chloride to form sodium chloride in both cases along with iron in the latter case. Additional ferrous chloride was added to two of the three batches to form low melting point consolidated mixtures of sodium chloride and ferrous chloride, whereas consolidation of a sodium-chloride product was performed in a separate batch. Samples of the products were characterized via X-ray diffraction to identify attendant compounds. The reaction of sodium metal with metered ammonium chloride particulate feeds proceeded without reaction excursions and produced pure colorless sodium chloride. The reaction of sodium metal with ferrous chloride yielded occasional reaction excursions as evidenced by temperature spikes and fuming ferrous chloride, producing a dark salt-metal mixture. This investigation into a method for controlled conversion of sodium metal to sodium chloride is particularly applicable to sodium containing elevated levels of radioactivity-including bond sodium from nuclear fuels-in remote-handled inert-atmosphere environments.

• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2753-2760
• /
• 2021

This paper proposes using sodium-cooled fast reactor technologies for use in hydrogen vapor methane (SMR) modification. Using three independent energy rings in the Russian BN-600 fast reactor, steam is generated in one of the steam-generating cycles with a pressure of 13.1 MPa and a temperature of 505 ℃. The reactor's second energy cycles can increase the gas-steam mixture's temperature to the required amount for efficient correction. The 620 ton/hr 540 ℃ steam generated in this cycle is sufficient to supply a high-temperature synthesis current source (700 ℃), which raises the steam-gas mixture's temperature in the reactor. The proposed technology provides a high rate of hydrogen production (approximately 144.5 ton/hr of standard H₂), also up to 25% of the original natural gas, in line with existing SMR technology for preparing and heating steam and gas mixtures will be saved. Also, exergy analysis results show that the plant's efficiency reaches 78.5% using HTR heat for combined hydrogen and power generation.

• Advances in concrete construction
• /
• v.13 no.5
• /
• pp.395-410
• /
• 2022

This study collected the results of material tests and full-scale pumping tests using 127 types of concrete mixtures with compressive strength ranging from 24 to 200 MPa. The results of 242 material tests showed high correlations between the viscosity of the lubricating layer and concrete, between the slump and the yield stress of concrete, between the water-binder ratio and the viscosity of lubricating layer, and between the time required to reach 500 mm of slump flow and concrete viscosity. Based on these correlations, pumpability was predicted using 101 pumping test conditions, and their accuracy was compared to the actual test results. When the rheological properties of concrete and the lubricating layer were directly measured, the prediction result showed the highest accuracy. A high accuracy can be achieved when the measured viscosity of the lubricating layer, a key determinant of concrete pumpability, is reflected in the prediction of pumpability. When measuring rheological properties is difficult, the slump test can be used to quantitatively predict the pumpability despite the lower accuracy than those of other prediction methods.

• Nuclear Engineering and Technology
• /
• v.54 no.5
• /
• pp.1909-1913
• /
• 2022

This work shows the technical feasibility to obtain uranium tetrafluoride through an electrochemical mercury cell. This technique represents a custom scaling-up methodology from our previous studies to obtain UF₄ using the dropping mercury electrode cell. The UF₄ products were obtained from natural UF₆ gas, which was hydrolyzed to obtain a 50 g/L UO₂F₂ solution. The electrolysis cell was made using a mercury reservoir, to reach UF₄ production rates of 1 Kg UF₄/day. This custom design allowed a stable UF₄ production thanks to the mercury cathode, which do not permit the accumulation of solid products in its surface. The cell was tested using current densities from 5.000 to 17.500 A/m² and temperatures from 25 to 65 ℃. The maximum current efficiency achieved under these conditions was 80%. The UF₄ powders possessed spherical morphology, with diameters between 20 and 80 ㎛. Compared to the SnCl₂ precipitation, this process did not allow preferential growth of the precipitates. This improved the compaction of the UF₄ - Mg powders mixtures, with densities between 3.0 and 3.5 g/cm³. The purity of the UF₄ products was over 98%.

• Journal of Powder Materials
• /
• v.9 no.6
• /
• pp.394-408
• /
• 2002

Nanostructured high strength metastable Al-, Mg- and Ti-based alloys containing different amorphous, quasicrystalline and nanocrystalline phases are synthesized by non-equilibrium processing techniques. Such alloys can be prepared by quenching from the melt or by powder metallurgy techniques. This paper focuses on one hand on mechanically alloyed and ball milled powders containing different volume fractions of amorphous or nano-(quasi)crystalline phases, consolidated bulk specimens and, on the other hand. on cast specimens containing different constituent phases with different length-scale. As one example. $Mg_{55}Y_{15}Cu_{30}$- based metallic glass matrix composites are produced by mechanical alloying of elemental powder mixtures containing up to 30 vol.% $Y_2O_3$ particles. The comparison with the particle-free metallic glass reveals that the nanosized second phase oxide particles do not significantly affect the glass-forming ability upon mechanical alloying despite some limited particle dissolution. A supercooled liquid region with an extension of about 50 K can be maintained in the presence of the oxides. The distinct viscosity decrease in the supercooled liquid regime allows to consolidate the powders into bulk samples by uniaxial hot pressing. The $Y_2O_3$ additions increase the mechanical strength of the composites compared to the $Mg_{55}Y_{15}Cu_{30}$ metallic glass. The second example deals with Al-Mn-Ce and Al-Cu-Fe composites with quasicrystalline particles as reinforcements, which are prepared by quenching from the melt and by powder metallurgy. $Al_{98-x}Mn_xCe_2$ (x =5,6,7) melt-spun ribbons containing a major quasicrystalline phase coexisting with an Al-matrix on a nanometer scale are pulverized by ball milling. The powders are consolidated by hot extrusion. Grain growth during consolidation causes the formation of a micrometer-scale microstructure. Mechanical alloying of $Al_{63}Cu_{25}Fe_{12}$ leads to single-phase quasicrystalline powders. which are blended with different volume fractions of pure Al-powder and hot extruded forming $Al_{100-x}$$(Al_{0.63}Cu_{0.25}Fe_{0.12})_x$ (x = 40,50,60,80) micrometer-scale composites. Compression test data reveal a high yield strength of ${\sigma}_y{\geq}$700 MPa and a ductility of ${\varepsilon}_{pl}{\geq}$5% for than the Al-Mn-Ce bulk samples. The strength level of the Al-Cu-Fe alloys is ${\sigma}_y{\leq}$550 MPa significantly lower. By the addition of different amounts of aluminum, the mechanical properties can be tuned to a wide range. Finally, a bulk metallic glass-forming Ti-Cu-Ni-Sn alloy with in situ formed composite microstructure prepared by both centrifugal and injection casting presents more than 6% plastic strain under compressive stress at room temperature. The in situ formed composite contains dendritic hcp Ti solid solution precipitates and a few $Ti_3Sn,\;{\beta}$-(Cu, Sn) grains dispersed in a glassy matrix. The composite micro- structure can avoid the development of the highly localized shear bands typical for the room temperature defor-mation of monolithic glasses. Instead, widely developed shear bands with evident protuberance are observed. resulting in significant yielding and homogeneous plastic deformation over the entire sample.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.3
• /
• pp.63-74
• /
• 2016

The objective of this study was to investigate the variations of physico-chemical properties during the swine manure composting, sawdust as the bulking agent was composted at different points (Top layer, Side of middle layer, Bottom layer). Air suction system with constant bottom aeration in bench scale reactors (30 L). The highest temperature was reached in the range of $58^{\circ}C$ to $62^{\circ}C$ on $3^{rd}$ day and this thermophilic phase (> $50^{\circ}C$) was continued for 3 days in all the treatment mixtures. However, the temperature was gradually decreased to room temperature at the end of 60 day composting process. Except control, the discharged ammonia ($NH_3$) was a maximum in the treatment order of Top layer>Bottom layer>Side of middle layer as 500 ppm, 162 ppm and 120 ppm, respectively, on the $4^{th}$ day and showing that Top layer point Air suction produce much more ammonia content than the other point. During the composting process, the total Kjeldahl nitrogen (TKN) was gradually increased due to the mass loss in the composting mixtures. At the same time, C/N ratio was decreased to Top layer, 13; Side of middle layer, 12 and Bottom layer, 13 at Air suction points. The significant reduction of C/N ratio in all different air suction system when manure was matured. The $NH_4-N$ to $NO_3-N$ ratio was recorded as 10.52 at the initial stage of the compost mixtures and reduced to 0.97 (Top layer), 0.70 (Side of middle layer), 3.2 (Bottom layer) because of manure decomposition. The overall results revealed that Top layer and Side of middle layer Air suction is a suitable option when compared other point for high quality composts.

• Journal of the Korean Society of Tobacco Science
• /
• v.27 no.1 s.53
• /
• pp.141-152
• /
• 2005

This study focused on the relationships among leaf and smoke components and sensory properties following tobacco leaf blending. A completely randomized experimental design was used to evaluate components of leaf and smoke and sensory properties for sample cigarettes with four mixtures of flue cured and burley tobacco (40:60, 60:40, 80:20 and 100:0). Eleven leaf components, six smoke components, and eight sensory properties of smoking taste were analyzed. A sensory evaluation method known as quantitative descriptive analysis was used to evaluate perceptual strength on a fifteen score scale. Raw data from ten trained panelists were obtained and statistically analyzed. Based on the MANOVA, clustering analysis, correlation matrix and partial least square (PLS) method were applied to find out which smoke component most affected sensory properties. The PLS method was used to remove the influence between explanatory variables in the leaf, smoke components derived from the results. High correlations (p<0.0l) were found among ten specific leaf and smoke components and sensory attributes. Total nitrogen, ammonia, total volatile base, and nitrate in the leaf were significantly correlated (p<0.05) with impact, bitterness, tobacco taste, irritation, smoke volume, and smoke pungency. From the results of PLS analysis, influence variables are used to explain about the correlation. In terms of bitterness, with only two explanatory variables, Leaf $NO_3$ and Leaf crude fiber were enough for guessing their correlation. In the distance weighted least square fitting analysis, carbon monoxide highly influenced bitterness, hay like taste, and smoke volume.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.12
• /
• pp.2792-2799
• /
• 2015

In this paper, we utilize source mel-frequency cepstral coefficients (SMFCCs), skewness, and kurtosis extracted in glottal flow signals to improve speaker recognition performance. Generally, because the high band magnitude response of glottal flow signals is somewhat flat, the SMFCCs are extracted using the response below the predefined cutoff frequency. The extracted SMFCC, skewness, and kurtosis are concatenated with conventional feature parameters. Then, dimensional reduction by the principal component analysis (PCA) and the linear discriminat analysis (LDA) is followed to compare performances with conventional systems under equivalent conditions. The proposed recognition system outperformed the conventional system for large scale speaker recognition experiments. Especially, the performance improvement was more noticeable for small Gaussan mixtures.