• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.388-388
• /
• 2016

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated with cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature $T_s$, and substrate dc bias $V_s$ as variables for efficient PEDOT:PSS/crystalline (c-)Si heterojunction solar cells (Fig. 1). The high-speed camera and differential mobility analysis characterizations revealed that average size and flux of PEDOT:PSS mist depend on f, solvent, and $V_s$. The size distribution of mist particles including EG/DI water cosolvent is also shown at three different $V_s$ of 0, 1.5, and 5 kV for a f of 3 MHz (Fig. 2). The size distribution of EG/DI water mist without PEDOT:PSS is also shown at the bottom. A peak maximum shifted from 300-350 to 20-30 nm with a narrow band width of ~150 nm for PEDOT:PSS solution, whose maximum number density increased significantly up to 8000/cc with increasing $V_s$. On the other hand, for EG/water cosolvent mist alone, the peak maximum was observed at a 72.3 nm with a number density of ~700/cc and a band width of ~160 nm and it decreased markedly with increasing $V_s$. These findings were not observed for PEDOT:PSS/EG/DI water mist. In addition, the Mie scattering image of PEDOT:PSS mist under white bias light was not observed at $V_s$ above 5 kV, because the average size of mist became smaller. These results imply that most of solvent is solvated in PEDOT:PSS molecule and/or solvent is vaporized. Thus, higher f and $V_s$ generate preferentially fine mist particle with a narrower band width. Film deposition occurred when $V_s$ was impressed on positive to a c-Si substrate at a Ts of $30-40^{\circ}C$, whereas no deposition of films occurred on negative, implying that negatively charged mist mainly provide the film deposition. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrate by adjusting $T_s$ and $V_s$. The adhesion of CMD PEDOT:PSS to c-Si enhanced by $V_s$ conspicuously compared to that of spin-coated film. The CMD PEDOT:PSS/c-Si solar cell devices on textured c-Si(100) exhibited a ${\eta}$ of 11.0% with the better uniformity of the solar cell parameters. Furthermore, ${\eta}$ increased to 12.5% with a $J_{sc}$ of $35.6mA/cm^2$, a $V_{oc}$ of 0.53 V, and a FF of 0.67 with an antireflection (AR) coating layer of 20-nm-thick CMD molybdenum oxide $MoO_x$ (n= 2.1) using negatively charged mist of 0.1 wt% 12 Molybdo (VI) phosphoric acid n-Hydrate) $H_3(PMo_{12}O_40){\cdot}nH_2O$ in methanol. CMD. These findings suggest that the CMD with negatively charged mist has a great potential for the uniform deposition of organic and inorganic on textured c-Si substrate by adjusting $T_s$ and $V_s$.

• Economic and Environmental Geology
• /
• v.40 no.6
• /
• pp.713-726
• /
• 2007

The Daebong deposit consists of gold-silver-bearing mesothermal massive quartz veins which fill fractures along fault zones($N10{\sim}20^{\circ}W,\;40{\sim}60^{\circ}SW$) within banded gneiss or granitic gneiss of Precambrian Gyeonggi massif. Ore mineralization of the deposit is composed of massive white quartz vein(stage I) which was formed in the same stage by multiple episodes of fracturing and healing and transparent quartz vein(stage II) which is separated by a major faulting event. The hydrothermal alteration of stage I is sericitization, chloritization, carbonitization, pyritization, silicification and argillization. Sericitic zone occurs near and at quartz vein and includes mainly sericite, quartz, and minor illite, carbonates and epidote. Chloritic zone occurs far from quartz vein and is composed of mainly chlorite, quartz and minor sericite, carbonates and epidote. Fe/(Fe+Mg) ratios of sericite and chlorite range 0.36 to 0.59($0.51{\pm}0.10$) and 0.66 to 0.73($0.70{\pm}0.02$), and belong to muscovite-petzite series and brunsvigite, respectively. Calculated $Al_{IV}-Fe/(Fe+Mg)$ diagrams of sericite and chlorite suggest that this can be a reliable indicator of alteration temperature in Au-Ag deposits. Calculated activities of chlorite end member are $a3(Fe_5Al_2Si_3O_{10}(OH){_6}=0.00964{\sim}0.0291,\;a2(Mg_5Al_2Si_3O_{10}(OH){_6}= 9.99E-07{\sim}1.87E-05,\;a1(Mg_6Si_4O_{10}(OH){_6}=5.61E-07{\sim}1.79E-05$. It suggest that chlorite from the Daebong deposit is iron-rich chlorite formed due to decreasing temperature from $T>450^{\circ}C$. Calculated $log\;{\alpha}K^+/{\alpha}H^+,\;log\;{\alpha}Na^+/{\alpha}H^+,\;log\;{\alpha}Ca^{2+}/{\alpha}^2H^+$ and pH values during wall-rock alteration are $4.6(400^{\circ}C),\;4.1(350^{\circ}C),\;4.0(400^{\circ}C),\;4.2(350^{\circ}C),\;1.8(400^{\circ}C),\;4.5(350^{\circ}C),\;5.4{\sim}6.5(400^{\circ}C)\;and\;5.1{\sim}5.5(350^{\circ}C)$, respectively. Gain elements (enrichment elements) during wallrock alteration are $K_2O,\;P_2O_5,\;Na2O$, Ba, Sr, Cr, Sc, V, Pb, Zn, Be, Ag, As, Ta and Sb. Elements(Sr, V, Pb, Zn, As, Sb) represent a potentially tools for exploration in mesothermal and epithermal gold-silver deposits.

• Economic and Environmental Geology
• /
• v.39 no.3 s.178
• /
• pp.329-342
• /
• 2006

The purpose of this study is to determine the geochemical characteristics for the stream sediments in the Konyang area. So we can estimate the environment contamination and understand geochemical disaster. We collect the stream sediments samples by wet sieving along the primary channels and slowly dry the collected samples in the laboratory and grind to pass a 200mesh using an alumina mortar and pestle for chemical analysis. Mineralogy, major, trace and rare earth elements are determined by XRD, XRE, ICP-AES and NAA analysis methods. For geochemical characteristics on the geological groups of stream sediments, the studied area was grouped into quartz porphyry area, sedimentary rock area, anorthosite area and gneiss area. Contents of major elements for the stream sediments in the Konyang area were $SiO_2\;41.86{\sim}76.74\;wt.%,\;Al_{2}O_{3}\;9.92{\sim}30.00\;wt.%,\;Fe_{2}O_{3}\;2.74{\sim}12.68\;wt.%,\;CaO\;0.22{\sim}3.31\;wt.%,\;MgO\;0.34{\sim}3.97\;wt.%,\;K_{2}O\;0.75{\sim}0.93\;wt.%,\;Na_{2}O\;0.25{\sim}1.92\;wt.%,\;TiO_{2}\;0.40{\sim}3.00\;wt.%,\;MnO\;0.03{\sim}0.21\;wt.%,\;P_{2}O_{5}\;0.05{\sim}0.38\;wt.%$. The contents of trace and rare earth elements for the stream sediments were $Cu\;7{\sim}102\;ppm,\;Pb\;15{\sim}47\;ppm,\;Sr\;48{\sim}513\;ppm,\;V\;29{\sim}129\;ppm,\;Zr\;31{\sim}217\;ppm,\;Li\;14{\sim}94\;ppm,\;Co\;5.6{\sim}32.1\;ppm,\;Cr\;23{\sim}259\;ppm,\;Cs\;1.7{\sim}8.7\;ppm,\;Hf\;2.1{\sim}109.0\;ppm,\;Rb\;34{\sim}247\;ppm,\;Sc\;4.5{\sim}21.9\;ppm,\;Zn\;24{\sim}609\;ppm,\;Sb\;0.8{\sim}2.6\;ppm,\;Th\;3{\sim}213\;ppm,\;Ce\;22{\sim}1000\;ppm,\;Eu\;0.7{\sim}5.3\;ppm,\;Yb\;0.6{\sim}6.4\;ppm$. Generally, the contents of $Al_{2}O_{3}\;and\;SiO_2$ had a good relationships with each other in rocks but it had a bad relationships in stream sediments for this study area. The contents of $Fe_{2}O_3$, CaO, MnO and $P_{2}O_{5}$ had a good relationships with major and minor elements in stream sediments of this study area. The contents of Co and V in the stream sediments had a good relationships with other toxic elements.

• Economic and Environmental Geology
• /
• v.31 no.4
• /
• pp.297-310
• /
• 1998

Geochemical characteristics of environmental toxic elements at the Narim mine area were investigated on the basis of major, minor, rare earth element geochemistry and mineralogy. Ratios of $Al_2O_3/Na_2O$ and $K_2O/Na_2O$ in soils and sediments range from 11.57 to 22.21 and from 1.86 to 3.93, and are partly negative and positive correlation against $SiO_2/Al_2O_3$ (3.41 to 4.78), respectively. These suggested that sediment source of host granitic gneiss could be due to rocks of high grade metamorphism originated by sedimentary rocks. Characteristics of some trace and rare earth elements of V/Ni (0.33 to 1.95), Ni/Co (2.00 to 6.50), Zr/Hf (11.27 to 53.10), La/Ce (0.44 to 0.55), Th/Yb (4.07 to 7.14), La/Th (2.35 to 3.93), $La_N/Yb_N$ (6.58 to 13.67), Co/Th (0.63 to 2.68), La/Sc (3.29 to 5.94) and Sc/Th (0.49 to 1.00) are revealed a narrow range and homogeneous compositions may be explained by simple source lithology. Major elements in all samples are enriched $Al_2O_3$, MgO, $TiO_2$ and LOI, especially $Fe_2O_3$ (mean=7.36 wt.%) in sediments than the composition of host granitic gneiss. The average enrichment indices of major and rare earth elements from the mining drainage are 2.05 and 2.91 of the sediments and are 2.02 and 2.60 of the soils, normalizing by composition of host granitic gneiss, respectively. Average composition (ppm) of minor and/or environmental toxic elements in sediments and soils are Ag=14 and 1, As=199 and 14, Cd=22 and 1, Cu=215 and 42, Pb=1770 and 65, Sb=18 and 3, Zn=3333 and 170, respectively, and extremely high concentrations are found in the subsurface sediments near the ore dump. Environmental toxic elements were strongly enriched in all samples, especially As, Cd, Cu, Pb, Sb and Zn. The level of enrichment was very severe in mining drainage sediments, while it was not so great in the soils. Based on the EPA value, enrichment index of toxic elements is 8.63 of mining drainage sediments and 0.54 of soils on the mining drainage. Mineral composition of soils and sediments near the mining area were partly variable being composed of quartz, mica, feldspar, amphibole, chlorite and clay minerals. From the gravity separated mineralogy, soils and sediments are composed of some pyrite, arsenopyrite, chalcopyrite, sphalerite, galena, goethite and various hydroxide minerals.

• Therapeutic Science for Rehabilitation
• /
• v.8 no.4
• /
• pp.19-31
• /
• 2019

Objective : The purpose of this study was to examine differences of psychological symptoms for mothers of infants with autism spectrum disorder(ASD) according to the level of parenting stress. Methods : The subjects were seventy-two mothers of infants with ASD(aged 22 months to 71 months) completed Korean Parenting Stress Index (K-PSI) and Minnesota Multiphasic Personality Inventory(MMPI-2). The data was analyzed using SPSS 23.0 program. Results : First, total and parent domain of parenting stress were positively correlated with several clinical scales of MMPI-2. However, there was no significant association between the child domain of parenting stress and clinical scale MMPI-2. Second, as a result of verified the difference of psychological symptoms according to level of total and parent domain of parenting stress, high-risks group was significantly higher scores in several clinical scales of MMPI-2 relative to those in normal range group. However, regarding the association between the child domain of parenting stress and psychological symptoms, there was no significant difference in psychological symptoms between high-risks group and normal range group. Conclusions : The results of this study have implications for verified the difference of psychological symptoms according to level of parenting stress among mothers of infants with ASD.

• KEPCO Journal on Electric Power and Energy
• /
• v.4 no.1
• /
• pp.25-31
• /
• 2018

A boiler system transforms water to pressured supercritical steam which drives the running of the turbine to rotate in the generator to produce electricity in power plants. Materials for building the tube system face challenges from high temperature creep damage, thermal fatigue/expansion, fireside and steam corrosion, etc. A database on the creep resistance strength and steam oxidation of the materials is important to the long-term reliable operation of the boiler system. Generally, the ferritic steels, i.e., grade 1, grade 2, grade 9, and X20, are extensively used as the superheater (SH) and reheater (RH) in supercritical (SC) and ultra supercritcal (USC) power plants. Currently, advanced austenitic steel, such as TP347H (FG), Super304H and HR3C, are beginning to replace the traditional ferritic steels as they allow an increase in steam temperature to meet the demands for increased plant efficiency. The purpose of this paper is to provide the state-of-the-art knowledge on boiler tube materials, including the strengthening, metallurgy, property/microstructural degradation, oxidation, and oxidation property improvement and then describe the modern microstructural characterization methods to assess and control the properties of these alloys. The paper covers the limited experience and experiment results with the alloys and presents important information on microstructural strengthening, degradation, and oxidation mechanisms.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.116-117
• /
• 2006

We investigated selective emitter effect of Porous Silicon (PSI) as antireflection coatings (ARC). The thin PSi layer, less than 100nm, was electrochemically formed by electrochemical method in about $3{\mu}m$ thick $n^+$ emitter on single crystalline silicon wafer (sc-Si). The appropriate PSi formations for selective emitter effect were carried out a two steps. A first set of samples allowed to be etched after metal-contact processing and a second one to evaporate Ag front-side metallization on PSi layer, by evaluating the I-V features The PSi has reflectance less than 20% in wavelength for 450-1000nm and porosity is about 60%. The cell made after front-contact has improved cell efficiency of about in comparison with the one made after PSi. The observed increase of efficiency for samples with PSi coating could be explained not only by the reduction of the reflection loss and surface recombination but also by the increased short-circuit current (Isc) within selective emitter. The assumption was confirmed by numerical modeling. The obtained results point out that it would be possible to prepare a solar cell over 15% efficiency by the proposed simple technology.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.10
• /
• pp.2272-2281
• /
• 1997

This paepr proposes a shared medium access control protocol for hgih-speed multimedia services of distributed subscriber home and small-sized business ATM networks. This protocol offers not only global fairness for the whole network at the same time, but also local fairness for different prioritytraffics on each node. Considering that the future B-ISDN service si a mixture of real and non-real time traffic data, this protocol is designed to accommodate the real time service, by controlling the priority of the real and non-real time data. The simulation results show that the proposed protocol has better performance than the other protocols.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.81.1-81.1
• /
• 2012

나노임프린트 리소그라피(Nano-Imprint Lithography, NIL) 기술은 기판위의 resin을 나노구조물이 각인된 스탬프로 눌러서 나노구조물을 형성하는 기술로, 경제적이고 효과적으로 나노구조물을 제작할 수 있는 기술이다. 그중에서도 UV 기반의 나노임프린트(UV-NIL) 기술은 resin을 투명한 스탬프로 누른뒤 UV로 경화시켜 나노구조물을 형성하는 기술로써 고온, 고압($140{\sim}180^{\circ}C$, 10~30bar)이 필요한 가열식 나노임프린트 기술에 비해 상온, 상압($20^{\circ}C$, 1bar)에서도 구조물 형성이 가능하여 다층구조 형성에 적합하다. 연속적인 임프린팅 공정에 의해 resin이 quarz 스탬프에 잔류하여 패터닝에 결함을 유발하게 되므로 오염물을 제거하기 위한 세정공정이 필요하다. 하지만 UV에 의해 경화된 resin은 cross-linking을 형성하여 화학적인 내성이 증가하게 되므로 제거하기가 어렵다. 현재는 resin 제거를 위한 세정공정으로 SPM($H_2SO_4/H_2O_2$) 세정이 사용되고 있는데 세정시간이 길고 세정 후에 입자 또는 황 잔유물이 남으며 많은 유해용액 사용의 문제점이 있어 효과적으로 resin을 제거할 세정공정이 필요한 상황이다. 본 연구에서는 친환경적인 UV 세정 및 오존수 세정공정을 적용하여 경화된 resin을 제거하는 연구를 진행하였다. 실험샘플은 약 100nm 두께의 resin을 증착한 $1.5cm{\times}1.5cm$ $SiO_2$ 쿠폰 wafer를 사용하였으며, UV 및 오존수의 처리시간을 달리하여 resin 제거효율을 평가하였다. ATR-FTIR 장비를 사용하여 시간에 따른 resin의 두께를 측정한 결과, UV 세정으로 100nm 높이의 resin중에 80nm의 bulk resin이 단시간에 제거가 되었고 나머지 20nm의 resin thin film은 오존수 세정으로 쉽게 제거되는 것을 확인 하였다. 또한 표면에 남은 resin residue와 particle을 제거하기 위해서 SC-1 세정을 진행하였고 contact angle과 optical microscope 장비를 사용하여 resin이 모두 제거된 것을 확인하였다.

• Anxiety and mood
• /
• v.8 no.1
• /
• pp.16-21
• /
• 2012

Objectives : The current study investigated the personality characteristics of the sexual offender using the Minnesota Multiphasic Personality Inventory (MMPI) test commonly used in clinical medicine. Methods : 30 sexual offenders (30 male) completed the Korean version of the MMPI. 20 of the 30 sexual offenders were patients with paraphilia. The sexual offenders had been admitted to the Institute of Forensic Psychiatry Ministry of Justice, Gongju, for sexual violence. Results : The MMPI scores of the sexual offenders were significantly higher on the psychopathic deviate (Pd), masculinity-feminity (Mf), paranoia (Pa), psychasthenia (Pt), schizophrenia (Sc) than the comparison group. And The MMPI scores of the sexual offenders had higher values for hypochondriasis (Hs), depression (D), hysteria (Hy), hypomania (Ma), social introversion (Si) than the comparison group, but were not significantly higher. Conclusion : Sexual offenders may be antisocial, paranoid, schizoid or psychasthenic. They seem to have psychotic psychopathology rather than neurotic psychopathology. These results suggested that the psychopatholgy of sexual offenders may be different to the control group.