• Journal of Forest and Environmental Science
• /
• 제28권4호
• /
• pp.263-267
• /
• 2012

Characteristics of charcoals manufactured in each temperature as 400, 600 800, 1,000 and $1,200^{\circ}C$ were examined. Sapwood and heartwood of Quercus variabilis that one of major species in charcoal materials were used for this experiment. Charcoal density was decreased highly 38-60% compared with wood density and density of sapwood was slightly decreased but heartwood was not changed with increasing carbonization temperature increase. Weight loss of sapwood and heartwood charcoal increased as carbonization temperature increases, and there is no difference between sapwood and heartwood charcoal. Refining degree of sapwood and heartwood charcoal was zero in charring over $800^{\circ}C$. Moisture and ash of sapwood and heartwood charcoal in each carbonization temperature were not differed between sapwood and heartwood. Volatile of sapwood charcoal was slightly higher than that of heartwood, and decreased as carbonization temperature increases. As the carbonization temperature increased, fixed carbon of sapwood and heartwood charcoal increased. Calorific values of charcoal prepared at $600^{\circ}C$ were 7,200-7,300 cal/g and then decreased slightly as carbonization temperature increased.

• Journal of the Korean Wood Science and Technology
• /
• 제23권1호
• /
• pp.28-34
• /
• 1995

Korean pine(Pinus koraiensis S. et Z.) is an economically important species in Korea because it will be harvested largely within next 20~30 years. The purpose of this study was to investigate changes in green moisture content, specific gravity and shrinkage in the stems of a Korean pine trees to provide fundamental information for technical processes. The followings are the results of this study. 1. There were about 110% differences in the heartwood and sapwood' green moisture contents (heartwood=59.5%; sapwood=170.6%). 2. There were no significant differences in average volumetric shrinkage between heratwood and sapwood, even though there were significant differences in moisture contents between them. Therefore, moisture content did not significantly influence on the shrinkage. 3. There was no significant relationship between height and shrinkage in heartwood. However, in the sapwood, shrinkage was highly correlated with the height. 4. Shrinkage levels were the most significant in south-bound direction and least significant in north-bound direction in both heartwood and sapwood. 5. There was a positive correlation between specific gravity and shrinkage in the sapwood. However, no such a relationship was found in the heartwood.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.46-54
• /
• 1996

This study was carried out to investigate the vacuum drying characteristics of 50mm- and 75mm- thick tree disks of some domestic softwoods for substituting the conventional hardwoods as the materials for wood crafts. Though the elapsed drying times from green to in-use moisture content(MC) were largely shortened by vacuum drying, the tree disks treated by EWS couldn't be dried to in-use MC, and so sapwood stains also were occurred severely. We suggest EWS treatment is undesirable for the species with very high sapwood portion or vacuum drying with hot water circulation heating system. Heart checks were slight, but sapwood checks, which have never been trouble in drying process of tree disks, were severe. For the reasonable explanation it is suggested MC differences between sapwood and heartwood were large and most of tree disks had already no barks before drying test. Ginkgo was vacuum-dried with very slight drying defects such as heart checks, sapwood checks. V-cracks and sapwood stains. In Korean red pine and pitch pine V-cracks were severely occurred. And it was found the special feature that most of these defected tree disks contained several V-cracks within one tree disk. It can be considered as the causes that the region of sapwood was defected by the several checks at the early drying stage because of the steep MC gradient along the radial direction, and then at the later drying stage the drying stresses due to differential shrinkage were concentrated on these brittle spots.

• Journal of the Korean Wood Science and Technology
• /
• 제15권2호
• /
• pp.67-78
• /
• 1987

This study was designed to investigate the effect of board thickness and ring angle on the characteristics including internal check. ring failure, surface check, end check, collapse, thickness shrinkage and width shrinkage of press-drying. The exprimental materials of 6mm-. 9mm- and 12mm-thick board were taken from heartwood and sapwood of oak (Quercus acutissima Carr.) respectively. And boards were numbered according to position in the log(No. 1 to No. 4 for heartwood :md No. 9 for sapwood). Press-drying was at $145^{\circ}C$ platen temperature and 3.5kg/$Cm^2$ platen pressure. The results of this study were summarized as follows. 1. Drying rates for sapwood materials were greater than those for heartwood materials. And drying rates for thinner materials were greater than those for thicker materials. 2. The thinner boards were. the severer surface checking developed in the heartwood materials, and surface checking for heartwood materials had no tendency in board position for the same thickness. Sapwood materials were completely free from surface checking. 3. End checking for heartwood materials had no tendency in board position. The greater deviation of ring angle from perfectly edge-grained was, the severer and checking developed in the sapwood materials. But end checking did not occur in 6mm-thick sapwood materials. 4. The greater deviation of ring angle from perfectly edge-grained was, the severer end checking developed for heartwood and sapwood materials. As board thickness increased, maternal checking developed more severely for heartwood and sapweed materials. 5. For heartwood materials, ring failure, reduced with increasing deviation of ring angle from perfectly edge-grained except 12mm-thick material and showed no significant difference attributable to board thickness. Sapwood materials were completely free from ring failure. 6. For heartwood and sapwood materials, collapse was slight and showed no significant differences attributable to both board thickness and board position. 7. As deviation of ring angle from perfectly edge-grained increased, shrinkage of board thickness decreased for heartwood and sapwood materials. 8. Shrinkage of board width showed no significant differences attributable to both board thickness and board position for heartwood and sapweed materials.

• Mycobiology
• /
• 제42권2호
• /
• pp.210-214
• /
• 2014

In Korea, mass mortality of Quercus mongolica trees has become obvious since 2004. Raffaelea quercus-mongolicae is believed to be a causal fungus contributing the mortality. To evaluate the pathogenicity of the fungus to the trees, the fungus was multiple- and single-inoculated to the seedlings and twigs of the mature trees, respectively. In both the inoculations, the fungus was reisolated from more than 50% of inoculated twigs and seedlings. In the single inoculations, proportions of the transverse area of non-conductive sapwood at inoculation points and vertical lengths of discoloration expanded from the points were significantly different between the inoculation treatment and the control. In the multiple inoculations, no mortality was confirmed among the seedlings examined. These results showed that R. quercus-mongolicae can colonize sapwood, contribute to sapwood discoloration and disrupt sap flows around inoculation sites of Q. mongolica, although the pathogenicity of the fungus was not proven.

• 임산에너지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2003

우리나라의 주요 조림수종으로 앞으로 대경재로 대량벌목 이용될 낙엽송의 가공와 이용을 위한 기초적 자료인 생재함수율, 비중 및 수축율의 수간내의 변동을 심ㆍ변재로 나누어 조사, 검토하였다. 심ㆍ변재간 생재함수율, 비중 및 수축율은 유의차를 보였다. 생재함수율의 방사방향 분포는 심재에서는 거의 일정한 함수율을 보이다가 변재에서 높아지는 현상을 보였고, 지상고 분포는 심재에서는 높아짐에 따라 함수율이 작아지고, 변재에서는 커지는 것으로 나타났다. 방향에 따른 비중의 차는 심ㆍ변재 모두 없었으며, 지상고에 따라서는 변재는 없었으나 심재에서는 차이를 나타냈다. 방향 및 지상고에 따른 수축율의 차는 대부분 심ㆍ변재에서 별다른 유의차가 관찰되지 않았으나, 변재 일부방향에서 북쪽방향의 수축율이 남쪽방향의 수축율보다 높은 것으로 나타났다.

• 한국가구학회지
• /
• 제22권3호
• /
• pp.199-207
• /
• 2011

Examined the color of ten species of Korean broadleaf trees were experimented based on $L^*a^*b^*$ values and color difference (${\Delta}E^*ab$) between sapwood and heartwood, in order to analyze and determine the color, a critical visual and decorative factor of the broadleaf trees that can be used for making woodcraft and furniture. According to the result, the entire sapwood and heartwood, except the heartwood of Populus tomentiglandulosa, showed positive value in whiteness, redness, and yellowness and therefore contained yellow and red. None of the species showed color difference between sapwood and heartwood that was trace (0~0.5), slight (0.6~1.5), or very much; whereas Populus maximowiczii showed noticeable color difference (1.5~3.0); Salix koreensis, Betula platyphylla var japonica, Carpinus laxiflora, and Castanea crenata, appreciable and Populus tomentiglandulosa, Juglans mandshurica, Betula schmidtii, Alnus japonica, and Quercus variabilis, much. The color characteristics of heartwood and sapwood of the ten Korean broadleaf tree species studied in this research can be used as basic data for woodcraft or furniture production, especially when replacing foreign woods with Korean ones, and also contribute to convergence researches for science, engineering, and design fields.

• Journal of the Korean Wood Science and Technology
• /
• 제24권3호
• /
• pp.12-17
• /
• 1996

This study was carried out to investigate some mechanical properties for wood rational utilization of heartwood and sapwood in radiata pine according to basic density, ring width and proportion of latewood which were grown in New Zealand. This result were summarized as follow: Heartwood showed 35.78(MPa) of the compression strength parallel to the grain while sapwood showed 42.08(MPa). The modulus of rupture in static bending was higher in sapwood showing 86.12(MPa) than in heartwood 72.99(MPa) Heartwood had 7.38(GPa) for the modulus of elasticity in static bending and sapwood 8.17(GPa). As the basic density and proportion of latewood increased: compression strength parallel to the grain, MOR and MOE in static bending had a tendency to increase. As ring width increased, the mechanical properties decreased.

• 한국산림과학회지
• /
• 제84권2호
• /
• pp.186-197
• /
• 1995

경기도 양평 지역에 생육하고 있는 리기다소나무, 낙엽송, 졸참나무 임분의 지상 부위 생체량과 엽면적을 추정하기 위해 흉고직경, 흉고단면적, 변재단면적, 변재부피 등의 변수를 이용하는 회귀식을 조제하였다. 지상 부위 생체량과 엽면적은 흉고직경, 흉고단면적, 변재단면적, 변재부피 등과 각각 통계적으로 유의한 상관 관계를 보였으며, 비슷한 직경급에서 3수종 모두 유사한 수간목부 생체량을 보였다. 그러나 수피, 잎, 가지와 지상 부위 총생체량과, 단위건중량당 엽면적 그리고 엽면적 변재단면적의 비에 있어 수종 간 차이가 뚜렷하였다. 생체량과 엽면적 추정을 위한 회귀식은 대상 수중의 잎의 습성과 수병에 영향을 받는 것으로 보이며, 이들 영향을 보다 확실하게 구명하치 위해서 상세한 연구가 필요한 것으로 사료된다.

• Journal of the Korean Wood Science and Technology
• /
• 제52권2호
• /
• pp.118-133
• /
• 2024

The sapwood portion of fast-growing teak is mostly ignored due to its inferior quality. One of the possibilities for utilizing sapwood waste is to convert it into activated carbon that has good adsorption capabilities. The raw materials used in this research were sapwood of 14-year-old fast-growing teak sapwood (FTS) waste, which was taken from three trees from community forests in Wonosari, Gunungkidul, Yogyakarta Special Region. FTS waste was taken from the bottom of the tree up to a height of 1.3 m. The activation process is conducted with an activation temperature of 750℃, 850℃, and 950℃. The heating duration consists of three variations: 30 min, 60 min, and 90 min. The quality evaluation parameters of activated carbon include yield, moisture content, volatile matter content, ash content, fixed carbon content, adsorption capacity of benzene, adsorption capacity of methylene blue, and adsorption capacity of iodine. The results showed that the activated carbon produced had the following quality parameters: yield of 75.61%; moisture content of 1.27%; volatile matter content of 9.98%; ash content of 5.43%; fixed carbon content of 84.58%; benzene absorption capacity of 8.58%; methylene blue absorption capacity of 87.73 mg/g; and iodine adsorption capacity of 948.19 mg/g. It can be concluded that activated carbon from FTS waste has good iodine adsorption, which fulfilled the SNI 06-3730-1995 quality standard. Due to the iodine adsorption ability of FTS waste activated carbon, the conversion of FTS waste to activated carbon is categorized as a potential method to increase the value of this material.