• 대한치과기공학회지
• /
• 제33권1호
• /
• pp.47-54
• /
• 2011

Purpose: To investigate shear bonding strength between dental zirconia ceramics with different surface treatment and metal bracket. Methods: Zirconia ceramics(LAVA, 3M ESPE, USA) were divided to 4 groups according to their surface treatment; no surface treatment(G1), sand blasting(G2), silane coating(G3), and sand blasting+silane coating(G4). Specimens were bonded to metal bracket using resin bond($Transbond^{TM}XT$, 3M Unitek, USA). Shear bond strength was measured using universal test machine(3366 INSTRON. U.S.A) with cross head speed of 1 mm/min. Microstructural investigation for fracture surface was performed after shear test. Results: Shear bonding strengths of single surface treatment groups (G2 and G3) were higher than no treatment group(G1). Combined Treatment Group (G4) showed the highest shear bond strength of 9.15MPa. Microstructural observation shows that higher shear bonding strength was obtained when debonding was occurred at metal bracket/resin interface rather than zirconia ceramic/resin interface. Conclusion: Surface treatment of zirconia is necessary to obtain higher bonding strength. Combined treatment can be more effective when surface the surfaces are kept clean and homogeneous.

• 한국가스학회지
• /
• 제20권6호
• /
• pp.16-22
• /
• 2016

연료가스용 탄소강관이 지하에 매설되는 경우 부식을 방지하기 위해 피복강관을 사용하고 있으며, 피복강관의 결함, 타공사, 시공시 피복의 손상에 대비하여, 방식전위를 이용하여 환원 분위기를 강제로 조성한다. 일반적으로 연료가스용 탄소강관이 지하에 매설된 경우 두 방법이 병행되어 사용되지만, 토양환경의 변화를 예측 할 수 없는 불확실성과 부식 정도 또는 피복의 손상 등 배관의 결함에 대해 육안으로 직접 관찰하기 어려운 문제가 공존한다. 매설배관의 부식이 발생하는 것을 직접적으로 관찰하기 어렵기 때문에, 이를 직접적으로 관찰하기 위한 방법 중 하나가 부식쿠폰을 이용한 방법이다. 본 연구에서는 3가지 토양(마사토, 진흙, 모래)과 방식전위 사용 여부에 따라 작성된 6가지의 시나리오를 토대로 약 1년간 부식쿠폰의 부식 정도를 파악하였다. 그 결과 방식전위가 흐르는 환경의 부식쿠폰은 부식이 전혀 발생하지 않았으며, 미방식 부식쿠폰은 모두 부식이 발생하였다. 토양에 따라서는 진흙에서 가장 적은 부식속도를 보였으며, 모래와 마사토는 유사한 경향을 갖는 것으로 확인되었다. 진흙의 경우 높은 함수량에 의해 국부부식이 발생하였으며, 모래에서 부식이 발생한 것은 모래에 함유된 화학적 성분에 기인한 것으로 확인되었다.

• Geomechanics and Engineering
• /
• 제13권1호
• /
• pp.99-117
• /
• 2017

Rock physics modeling of sandstone reservoir from gas fields of Krishna-Godavari basin represents the link between reservoir parameters and seismic properties. The rock physics diagnostic models such as contact cement, constant cement and friable sand are chosen to characterize reservoir sands of two wells in this basin. Cementation is affected by the grain sorting and cement coating on the surface of the grain. The models show that the reservoir sands in two wells under examination have varying cementation from 2 to more than 6%. Distinct and separate velocity-porosity and elastic moduli-porosity trends are observed for reservoir zones of two wells. A methodology is adopted for generation of Rock Physics Template (RPT) based on fluid replacement modeling for Raghavapuram Shale and Gollapalli Sandstones of Early Cretaceous. The ratio of P-wave velocity to S-wave velocity (Vp/Vs) and P-impedance template, generated for this above formations is able to detect shale, brine sand and gas sand with varying water saturation and porosity from wells in the Endamuru and Suryaraopeta gas fields having same shallow marine depositional characters. This RPT predicted detection of water and gas sands are matched well with conventional neutron-density cross plot analysis.

• 한국주조공학회지
• /
• 제10권1호
• /
• pp.31-42
• /
• 1990

The full mould casting process in one of the newly developed techniques which has many advantages. Unbonded sand mould has been prepared for the major mould and $CO^2$ gas mould has been used occasionally for comparison. Patterns were built up with expanded polystyrene and coated with three different materials. Silica, graphite and zircon were used for the coating layer. The effects on fluidity and temperature loss of molten metals were investigated. The molten metals were Al-5% Si alloy, Cu-30% Zn alloy and gray iron of approximately 4.0% of carbon equivalent. Experimental variables were runner section area, superheat, sprue height, coating materials, coating thickness and apparent density of EPS pattern. The effects of coating materials on fluidity and temperature loss of the molten metals during transient pouring are summarized as follows : As runner section area, superheat and sprue height increased, fluidity increased. Temperature loss decreased as runner section area and sprue height increased. However, reversed effects were observed in the case of superheat increment. The coating materials decreased the fluidity of each alloy in the order of silica, graphite and zircon. Zircon brought to the highest temperature loss among the coating materials used. The fluidity increased in the order gray iron, Cu-30% Zn and Al-5% Si alloy while temperature loss in the reverse order. Especially in case of reduced pressure process, the fluidity was increased apparently. Al-5% Si alloy showed the lowest temperature loss among the alloys. The increment of the apparent density of EPS pattern resulted in the fluidity decrease and temperature loss increase. The relation between fluidity and temperature loss of each alloy can be expressed by the following equation within the coating thickness limit of 0.5-1.5㎜. F^*={\frac{a}{T^*-b}}-c$ where, $F^*$ : fluidity in the Full mould, $T^*$ : temperature loss in the mould. a : parameter for full mould. b, c : constants.

• 수산해양교육연구
• /
• 제22권4호
• /
• pp.501-507
• /
• 2010

The ceramic contained paint was made to replace the lead sinker for gill-net with coated lead sinker. The ceramic contained paints were coated in various conditions on the lead sinker with 19g of weight and the optimal coating condition was studied. The adaptability of the coated lead sinker was checked through the anti durability test and fishing operation with gill-net. The case of "Main material 70 wt% + Urethane thinner 30 wt% (Main material 700 $m{\ell}$ + Thinner 300 $m{\ell}$)" showed the best in the coating characteristics depending on the combination ratio of the ceramic paint contained. The coated lead sinker dried at $100^{\circ}C$ inside oven was superior to the drying in the room temperature in its surface glossiness and anti durability and faster drying time than the one dried in normal temperature. The quadruple layers of coating on lead sinker with 4 times of dipping and drying application showed the super anti durability in the coating characteristics depending on the frequency of dipping. When press is applied to the coated lead sinker, the coated layer is not detached from the sinker. In addition, the coated lead sinker was not damaged or peeled at the fishing operation about 2 months in various depths within 50m and by the materials at the bottom (sand, stone and gravel stone) and it was in good condition.

• Environmental Engineering Research
• /
• 제14권1호
• /
• pp.41-47
• /
• 2009

Column experiments were performed in this study to investigate humic acid adhesion to iron oxide-coated sand (ICS) under different experimental conditions including influent humic acid concentration, flow rate, solution pH, and ionic strength/composition. Breakthrough curves of humic acid were obtained by monitoring effluents, and then column capacity for humic acid adsorption ($C_cap$), total adsorption percent (R), and mass of humic acid adsorbed per unit mass of filter media ($q_a$) were quantified from these curves. Results showed that humic acid adhesion was about seven times higher in ICS than in quartz sand at given experimental conditions. This indicates that humic acid removal can be enhanced through the surface charge modification of quartz sand with iron oxide coating. The adhesion of humic acid in ICS was influenced by influent humic acid concentration. $C_cap$ and $q_a$ increased while R decreased with increasing influent humic acid concentration in ICS column. However, the influence of flow rate was not eminent in our experimental conditions. The humic acid adhesion was enhanced with increasing salt concentration of solution. $C_cap$, $q_a$ and R increased in ICS column with increasing salt concentration. On the adhesion of humic acid, the impact of CaCl2 was greater than that of NaCl. Also, the humic acid adhesion to ICS decreased with increasing solution pH. $C_cap$, $q_a$ and R decreased with increasing solution pH. This study demonstrates that humic acid concentration, salt concentration/composition, and solution pH should be controlled carefully in order to improve the ICS column performance for humic acid removal from water.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.55-62
• /
• 2017

The grate bar, a component used in steel mills, is used in harsh environments where external disturbances such as high temperature, abrasion, corrosion, and impacts are present. Therefore, in this study, spray-coating was performed on the most severely affected surface to extend the lifetime of the grate bar. The thermal and mechanical properties of the sprayed coated bars were investigated based on the performances under abrasion, thermal shock, tension, and sand blasting, and the microstructures by microscope. By analyzing the thermal and mechanical properties of the uncoated original grate bar and coated grate bar and comparing them with one another, the physical performance improvement of the coated grate bar can be verified.

• 한국농공학회논문집
• /
• 제46권3호
• /
• pp.73-81
• /
• 2004

FRP reinforcing bars(rebars) are produced through a variety of manufacturing process includes pultrusion, and filament winding and braiding etc. Each manufacturing method produces a different surface condition of FRP rebar. The surface properties of FRP rebar is an important property for mechanical bond with concrete. Current methods of providing surface deformation to FRP rebars include helical wrapping, surfaces and coating and rib molding. The problem with the helical wrapping method is that it can not provide enough surface deformation for good bond and it can be easily sheard off from the FRP rebars. Sand coating and rib molding provide surface deformation only to the outer FRP skins. Therefore, FRP rebar has about 60% of bond strength of steel rebar. The main objective was to evaluate the bond properties of FRP rebar after environmental exposure. Five types of FRP rebar includes CFRP ISO, GFRP Aslan, AFRP Technora CFRP(Korea), and GFRP(Korea) rebars performed direct bond tests. Also, FRP rebar bond specimens were subjected to exposure conditions including alkaline solution, acid solution, salt solution and deionized water etc. According to bond test results, CFRP(Korea) and CFRP(Korea) rebars were found to have better bond strength with concrete than previous FRP rebars. Also, FRP(Korea) rebar had more than about 70% in bond strength of steel rebar.

• 대한치과보철학회지
• /
• 제38권5호
• /
• pp.659-674
• /
• 2000

A large increase in the use of thin film coating of hydroxyapatite(HA) in implant dentistry is driven by the desire to take advantage of the excellent biocompatibility and high strength of HA coating. The purpose of this study was to evaluate the effects of HA-coated implants by ion Beam Assisted Deposition(IBAD) method in comparison to the sand-blasted and machined surfaces. Osteoblast culture test, removal torque test and histomorphometric analysis were performed and the following results obtained; 1. Examination of the osteoblast cultures displayed no difference in the secretion of alkaline phosphatase between the various specimen, but IBAD with pure HA specimen showed low alkaline phosphatase secretion(p<0.05). 2. Removal torque tests showed HA-coated implants by IBAD method to be similar in high value to the implants with sand-blasted surface than the implants with machined surface. And the ovariectomized group showed low mechanical test value than the normal group(p<0.05). 3. Histomorphometrical comparisons were performed on undecalcified ground sections. HA-coated implants by IBAD method demonstrated the highest mean bone-to-metal contact ratio on all threads and 3-best consecutive threads, and the implants with sand-blasted surface and implants with machined surface was in the next consecutive order(p<0.05). HA-coated implants showed slightly higher bone-to- metal contact ratio than sand-blasted implants, but no statistically significant difference was obtained between the two materials. The ovariectomized group showed lower value of bone-to-metal contact ratio than the normal group, but no statistically significant difference was obtained between the two groups. 4. Evaluation of bone volume on all threads and 3-best consecutive threads showed no statistically significant difference among the different surface treatment groups, but showed lower bone volume in ovariectomized group than in the normal group(p<0.05). According tn these results, thin film coated implants with HA showed high bone contact ratio, bone volume and removal torque strength in the short term, but long term observation is needed.

• 한국가스학회지
• /
• 제2권1호
• /
• pp.23-27
• /
• 1998

음극방식 시스템의 방식전류에 의한 압입구간내의 압입관과 배관의 부식거동에 관한 수학적 모델링을 경계요소법을 이용하여 수행하였다. 모델은 비선형 경계조건(Tafel 방정식)을 가진 라플라스 방정식으로 이루어져 있으며 압입관의 혼합전위를 구하기 위하여 혼합전위 이론을 응용한 반복법을 사용하였으며 그 위에 비선형 경계조건에 대한 해석을 위하여 이중 반복법을 사용하였다. 모델은 정상적인 압입구간 뿐만 아니라 압입관과 배관과의 금속간 접촉(metal touch)이나 외부환경과 압입구간 내부를 격리시키는 절연부위의 손상과 같은 결함들을 가진 비정상적인 압입구간에서의 각각의 경우에 대해서도 적용되었다. 수학적 모델링의 결과로부터 압입구간내의 전위분포나 전류분포를 계산할 수 있었다. 모델링의 타당성을 증명하기 위하여 모사실험을 수행하였으며 실험조건내에서 이론적인 결과와 실험결과는 정상적으로 잘 일치하였다.