• Journal of the Korean Society of Safety
• /
• v.13 no.3
• /
• pp.135-142
• /
• 1998

This paper is to investigate the failure surface and modes in a soil mass by a excavation of the model ground. To study the failure surface for the excavated slope, centrifugal model tests were performed by changing the angle of the excavated slope(50, 75, $90^{\circ}$) and the ground condition($D_r$=60, 90%, dry and submerged ground). Excavation was simulated during the centrifuge tests by operating a valve that allowed the zinc chloride solvent to drain from the excavation. Results of model tests were compared with those obtained with theoretical solutions using limit equilibrium analysis method. The results of model tests show that, there is a failure to create a straight line in the low angle of excavated surface and a create a circle as the angle increases. Also, as the angle of excavated surface is increasing, the angle of the failure surface increases. The failure length in the submerged ground increases approximately 1.10~1.34 times more than that of the dry ground.

• Journal of the Korea Society for Simulation
• /
• v.29 no.1
• /
• pp.1-9
• /
• 2020

The ballistic missile threat continues to increase with the proliferation of missile technology. In response to this threat, many kinds of interceptors have been emphasized over the years. For development of interceptor, systematic flight tests are essential. Flight tests provide valuable data that can be used to verify performance and confirm the technological progress of ballistic missile defense system including interceptor. However, during flight tests, civilians near the test region could be risk due to a lot of intercept debris. For this reason, reliable estimate of safety area for the flight tests should be preceded. In this study, prediction of safety area is performed through modeling and simulation. Firstly, behaviors of ballistic missile and interceptor are simulated for those entire phase including interception to obtain the relative intercept velocity and the relative impact angle. By using obtained data of kinetic energy, the fragment ejection velocity is calculated and fragment trajectories are simulated by considering drag, gravity and wind effects. Based on the debris field formation and hazard evaluation of debris, final safety area is calculated.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.627-632
• /
• 2005

In this study, a series of large-scale oedometer tests was performed to investigate the compressibility of rock fill materials. The testing samples were prepared to have three different grain size distributions and for each distribution, exist in two different states(dried and saturated). The test results indicated that particle breakages occurred mainly for the particles larger than 4.75mm in size and increased with increasing grain sizes. Also, it was found that, for a dry sample as it became well-graged, its compressibility decreased and accordingly, its tangent constrained modulus increased. A comparion between the samples in dry and saturated states revealed that compressibility of the materials increases with increasing water content. The values of tangent constrained modulus calculated for the tested dry samples were larger by about 10 to 20%, on average, than those for the saturated samples.

• Journal of the Korean Society of Safety
• /
• v.9 no.2
• /
• pp.18-25
• /
• 1994

In this thesis, the fatigue tests were performed on a series of reinforced concrete to Investigate the variation of strength and the safety of reinforced concrete structures under fatigue load. The specimens were of the same rectangular cross-section, of effective height 24cm and width 30cm and their span was 330cm. The three point loading system is used in the fatigue tests. In these tests, the fracture mode of reinforced concrete structures under fatigue load, relationship between the repeated loading cycles and the mid-span displacement of the specimens were observed. According to the test results, the following fatigue behavior of reinforced concrete specimens were observed. By increasing of the number of repeated loading cycles, the mid-span displacement became greater, however the Incremental amounts of the displacement were reduced. It could be also known that the inelastic strain energy of the doubly reinforced rectangular beams was larger than that of the singly reinforced rectangular beams as increasing the number of repeated loading cycles. Compliance of reinforced concrete structures tended to be reduced as increasing the repeated loading cycles, and the compliance of the doubly reinforced rectangular beams was generally smaller than that of the singly reinforced rectangular beams. Based on the above investigation, it could be concluded that the doubly reinforced rectangular beams under fatigue load were more efficient to resist the brittle fracture than the singly reinforced rectangular beams.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.293-298
• /
• 2015

A safety vent is crucial to protect its user from unpredictable explosions caused by increasing internal pressure of the lithium-ion batteries. In order to prevent the explosion of the battery, a safety vent rupture is required when the internal pressure reaches a critical value. In conventional manufacturing, the cap plate and the safety vent are fabricated separately and subsequently welded to each other. In the current study, a manufacturing process including a backward extrusion and coining process is suggested to produce an integral safety vent which also has the benefit of increasing production efficiency. FE simulations were conducted to predict the rupture pressure and to design the safety vent using a ductile fracture criterion and the element deletion method. The critical value, C, in the ductile fracture criterion was obtained from uniaxial tensile tests with an annealed sheet of 1050-H14 aluminum alloy. Rupture tests were preformed to measure the rupture pressure of the safety vent. The results met the required rupture pressure within 8.5±0.5 kgf/cm². The simulation results were compared with experimental results, which showed that the predicted rupture pressures are in good agreement with experimentally measured ones with a maximum error of only 3.9%.

• Journal of the Korean Institute of Gas
• /
• v.9 no.3 s.28
• /
• pp.32-37
• /
• 2005

Hose bands, which are used in LPG (Liquefied Petroleum Gas) or LNG (Liquefied Natural Gas) facilities for home use to join low pressure hoses with fuse-cocks (or regulators), should give a tight connection to prevent a gas leakage from hose connection parts. In this paper, hydraulic pressure tests and pull force tests were carried out to evaluate the performance and swaging length of hose bands. Experimental results showed that the swaging force of ear type bands were higher than those of spring bands and also showed that the optimal swaging length was about 1${\~}$2 mm from the hose end.

• Journal of Auto-vehicle Safety Association
• /
• v.6 no.2
• /
• pp.49-54
• /
• 2014

Development in vehicle industry could increase interest in children's safety recently. However the research of children safety is not being conducted as many as that of adult's. Especially the basic study for the vehicle crash on-board children was not much. This study focused on the effect of seatbelt anchorage points to evaluate children's safety in frontal crash. The current regulation of the seatbelt anchorage points is suitable for ranged from female 5% to male 95%. The assessment of children's safety at buckle up of no used CRS(child restraint system) was performed using frontal sled tests. The frontal crash pulse in sled tests was designed to the average of about 30 KNCAP frontal crash pulses. To reduce number of experiments, DOE is used. The Q6 child dummy and standard seat in UN R 129 were used. According to the analysis of test results, children's safety has been influenced by the points of seatbelt anchorage.

• Journal of Auto-vehicle Safety Association
• /
• v.12 no.1
• /
• pp.33-38
• /
• 2020

Since a diesel vehicle scandal related to the 'A' automobile company was issued in the United States in 2015, many countries have been interested in emission defeat devices. Being embedded in some diesel passenger cars sold in Korea, a defeat device for exhaust gas may have influence on both fuel economy and NOx emissions. In order to examine such effects, we carried out laboratory indoor tests as well as real road driving tests using four models of 'A' automobile company which may employ defeat devices. Those tests were performed observing the test modes of FTP-75, HWFET, and NEDC. Although fuel economy and NOx emissions according to indoor tests comply with the suggested tolerance, the findings in the real road driving tests do not satisfy the tolerance. Along with the results provided in this study, further evaluation may be necessary to investigate the noticeable difference between the indoor and real road tests.

• Journal of Food Hygiene and Safety
• /
• v.11 no.4
• /
• pp.315-321
• /
• 1996

Various antimicrobial drug screen tests have been used in order to ensure food safety. However, the conventional screen tests, the Swab Test on Premises(STOP, USA), the Calf Antibiotic and Sulfa Test(CAST, USA) and the European Economic Community 4-plate Test(FPT, EU) are not sufficiently rapid or sensitive enough to detect low levels of sulfa drugs in meat. We developed a new screen test kit for the determination of the antimicrobial residues in meat called the Bacillus megaterium Disk Assay(BmDA). A comparison of BmDA with the older screen tests showed BmDA was as good as the older ones with several advantages. The new test kit is faster-it can be read in 4∼6 hours instead of 16∼18 hours. Moreover, BmDA can discriminate sulfa drugs from other antimicrobial drugs because p-aminobenzoic acid countacts the inhibiting action of sulfa drugs. Minimum detectable levels of sulfa drugs were significantly improved at the lever of 0.025*0.1 pp, compared with the level of 1.0 ppm in FPT. A comparison of BmDA with the older screen tests in HPLC confirmed meat samples exceeded the Korean tolerance value of 0.1 ppm showed BmDA was the most sensitive in the microbiological screen tests. As the microbiological screen tests have already known, a person familiar with simple laboratory techniques should have no difficulty in using it to detect antimicrobial residues in meat. This would be a simple, economic method of antimicrobial residues detection which might be succesfully used by many laboratories.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2003.05a
• /
• pp.74-79
• /
• 2003

Many marine wastes such as seaweeds are casted aside at the seasides. So, the objective of this study is to apply the marine wastes to the concrete. To this end, mortar and concrete tests with the marine wastes have been conducted. The results of the present mortar and concrete tests indicate that the mortar and concrete with marine wastes admixtures exhibits very low permeability. The present study provides a firm base for the use of very low permeable concrete and the application of the marine structures and the submerged structures.