• Journal of Korean Society of Forest Science
• /
• v.87 no.2
• /
• pp.276-285
• /
• 1998

The aboveground biomass and nutrient content (N, P, K, Ca and Mg) of Pinus koraiensis S. et Z., aged 9, 22, 34, 46, 66 years, were measured in the Experiment Forest of Kangwon National University of Kangwondo province. The site index of the stands ranged from 13.5 to 14.2. Allometric equations (logY=alogX+b, where Y, X is ovendry mass and DBH, respectively) relating dry weights of stem, branches and needles to diameter at breast height (DBH) were developed to estimate aboveground tree biomass. Total above ground tree biomass increased with stand age from $21.8t\;ha^{-1}$ in the 9-year-old stand to $130t\;ha^{-1}$ in the 66-Year-old stand. Aboveground biomass was allocated as follows : stem> branch > foliage, except for the 9-year-old stand which had a greater proportion of foliage biomass than branch biomass. As stand age increased, an increasing proportion of annual biomass increment was allocated to stems. The aboveground biomass of shrubs and herbs ranged from 0.4 to $3.9t\;ha^{-1}$ and from 0.05 to $0.6t\;ha^{-1}$, respectively. No relationship was found between aboveground understory biomass and stand age. The mass of woody debris and forest floor varied between 0.59 to $1.54t\;ha^{-1}$ and 6.0 to $21.63t\;ha^{-1}$, respectively. Nutrient accumulation in aboveground tree biomass increased with stand age and was in the order of N > Ca > K > P > Mg. Average rates of nutrients accumulation in biomass were greatest in the early stages of stand development, and less marked as stand aged. The nutrient concentrations in different tree components decreased in the order of needle > branch > stem. There were no detectable trends in nutrient content of the forest floor and mineral soils with stand age. Understory vegetation contributed little to the nutrient pool of these Korean pine ecosystems. Mineral soil contained the Breast proportion of nutrient capital of the various ecosystem compartments.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.4
• /
• pp.207-217
• /
• 2011

In this study the complex formation reactions between uranium(VI) and 2,6-dihydroxybenzoate (DHB) as a model ligand of humic acid were investigated by using UV-Vis spectrophotometry and time-resolved laser-induced fluorescence spectroscopy (TRLFS). The analysis of the spectrophotometric data, i.e., absorbance changes at the characteristic charge-transfer bands of the U(VI)-DHB complex, indicates that both 1:1 and 1:2 (U(VI):DHB) complexes occur as a result of dual equilibria and their distribution varies in a pH-dependent manner. The stepwise stability constants determined (log $K_1$ and log $K_2$) are $12.4{\pm}0.1$ and $11.4{\pm}0.1$. Further, the TRLFS study shows that DHB plays a role as a fluorescence quencher of U(VI) species. The presence of both a dynamic and static quenching process was identified for all U(VI) species examined, i.e., ${UO_2}^{2+}$, $(UO_2)_2{(OH)_2}^{2+}$, and $(UO_2)_3{(OH)_5}^+$. The fluorescence intensity and lifetimes of each species were measured from the time-resolved spectra at various ligand concentrations, and then analyzed based on Stern-Volmer equations. The static quenching constants (log $K_s$) obtained are $4.2{\pm}0.1$, $4.3{\pm}0.1$, and $4.34{\pm}0.08$ for ${UO_2}^{2+}$, $(UO_2)_2{(OH)_2}^{2+}$, and $(UO_2)_3{(OH)_5}^+$, respectively. The results of Stern-Volmer analysis suggest that both mono- and bi-dentate U(VI)-DHB complexes serve as groundstate complexes inducing static quenching.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.27 no.1
• /
• pp.46-61
• /
• 1985

This study was performed to obtain the basic data which can be applied to the use of foaming mortars. The data was based on the properties of foaming mortars depending upon various mixing ratios and addings to compare those of cement mortar. The foaming agents which was used at this experiment were pre-foamed type and mix-foaming type which is being used as mortar structures. The foaming mortar, mixing ratios of cement to fine aggregate were 1:1, 1: 2, 1 : 3 and 1 : 4. The addings of foaming agents were 0.0%, 0.5%, 1.0%, 1.5%, 2.0%, 2.5% and 3.0% of cement weight. The results obtained were summarized as follows; 1. At the mixing ratio of 1 : 1, the lowest water-cement ratios were showed by foaming mortars, respectively. But it gradually was increased in poorer mixing ratio and decreased in more addition of foaming agent. The water-cement ratios were decreased up to 1. 8~22. 0% by G, 2. 2~24. 1 % by U and 0. 7~53. 1% by J foaming mortar than cement mortar. 2, At the mixing ratio of 1 : 1, the highest bulk densities were showed by foaming mortars, respectively. But, it gradually was decreased in poorer mixing ratio and more addition of foaming agent. The bulk densities were decreased up to 1. 4~20. 7% by G, 2. 3~23. 7% by U and 26. 5~56. 5% by J foaming mortar than cement mortar. Therefore, foaming mortar could be utilized to the constructions which need low strengths. 3. At the mixing ratio of 1:1, the lowest absorption rates were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Specially, according to the absorption rate when immersed in 72 hours, the absorption rates were showed up to 1. 01~1. 24 times by G, 1. 03~1. 58 times by U and 1. 10~5. 91 times by J foaming mortar than cement mortar. It was significantly higher at the early stage of immersed time than cement mortar. 4. At the mixing ratio of 1:1, the lowest air contents were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Air contents were contented up to 4. 0~17. 2 times by G, 5. 2~23. 2 times by U and 23. 8~74. 5 times by J foaming mortar than cement mortar. 5. At the mixing ratio of 1 : 1, the lowest decreasing rates of strengths were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Specially, the strengths of 28 days were decreased 0. 4~2. 2% than those of 7 days by foaming mortar, respectively. Also, the correlations between compressive and tensile strength, compressive and ending strength, tensile and bending strength were highly significant as a straight line shaped, respectively. 6. The correlations between absorption rate, air content, compressive strength and bulk density, absorption rate, compressive strength and air content were highly significant, respectively. The multiple regression equations of water-cement ratio, bulk density, absorption ate, air content, compressive strength, tensile strength and bending strength were computed depending on a function of mixing ratio and addition of foaming agent. It was highly significant, respectively. 7. At the mixing ratio of 1 : 1, the highest strengths were showed by cement mortar and foaming mortars, by chemical reagents. But, it gradually was decreased in poorer mixing ratio. The decreasing rates of strengths were in order of H $_2$S0 $_4$, HNO$_3$ and HCI, J,U,G foaming mortar and cement mortar. Specially, at the each mixing ratio, each chemical reagent and 3.0% of foaming agent, J foaming mortar was collapsed obviously. Therefore, for the structures requiring acid resistence, adding of foaming agent should be lower than 3.0%.

• Journal of Wetlands Research
• /
• v.18 no.3
• /
• pp.301-312
• /
• 2016

This study has performed comparative analysis on characteristics of contaminated 35 tributaries on seasonal variation/point discharge load/pollutant distribution of water quality factors(8) in order to understand the effect of the watershed in Nakdong River Basin. As a results, the water quality of $BOD_5$(Biochemical Oxygen Demand), Chl-a(Chlorophyll a) and Fecal E. Coli shows II grade at tributaries of more than 50% without COD(Chemical Oxygen Demand), TP(Total Phosphate), TOC(Total Oxygen Carbon) and TN(Total Nitrogen) factors. The specific discharge(Q) were occupied about 54.4% (19 sites) as $0.05m^3/sec/km^2$ value. Among these results, the contaminant level of Dalseocheon, Hyeonjicheon, Seokkyocheon 1, Uriyeongcheon and Dasancheon was also high, which has to consider a discharged pollutant load(kg/day). The 35 major tributaries of Nakdong River were included in 7 mid-watershed, such as Nakdong Waegwan, Geumho River, Nakdong Goryung, Nakdong Changnyung, Nam River, Nakdong Milyang, Nakdong River Hagueon. Especially, the discharged pollutant load of Nam River and Geumho River also was high according to the amount of discharge such as Kachang dam, Gongsan dam and Nam river dam. Seasonal difference of the water quality factors such as $BOD_5$, TN, SS and Q was observed largely, on the other hand the TP and Chl-a was not. This is guessed due to the precipitation effect of site, biological and physicochemical degradation properties of pollutant and etc. The co-relationship between the seasonal difference and water quality factors was observed using a Pearson correlation coefficients. Besides, the Multiple Regression analysis using a Stepwise Regression method was conducted to understand the effect between seasonal difference and water quality factors/regression equations. As a result, the Multiple Regression analysis was adapted in the spring, summer and autumn without the winter, which was observed high at spring, summer and autumn in the order COD/TP, Chl-a/TOC, TOC/COD/$BOD_5$ water quality factors, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• Journal of the Korean Magnetics Society
• /
• v.11 no.3
• /
• pp.85-96
• /
• 2001

Experimental magnetization-temperature curves for melt-spun ribbons of amorphous alloys (Dy$\_$0.33/Fe$\_$0.67/)$\_$1-x/B$\_$x/(x=0 ,0.05, 0.1, and 0.15) and (Sm$\_$0.33/Fe$\_$0.67/)$\_$1-x/B$\_$x/(x=0, 0.01, 0.02, and 0.03) (in atomic fraction) are fitted with theoretical equations based on the mean field theory in order to calculate exchange couplings between constituent elements as a function of the B content. In the case of the DyFe$_2$-B system, the sign of the exchange coupling between Dy and Fe is negative, indicating that the magnetization direction of Dy is antiparallel to that of Fe. The sign of the other two couplings are positive indicating a parallel alignment. The exchange coupling between Fe ions are greatest, while that between Dy ions is negligible. In the case of the SmFe$_2$B alloys, the sign of all the couplings are positive, indicating ferromagnetic coupling between the spins. The exchange couplings between Fe ions, and Fe and Sm are comparable to each other, but they are much greater than that between Sm ions. The high exchange coupling between Fe and Sm, which is considered to occur indirectly, is rather unexpected, but it is considered to be unique characteristics of amorphous Sm-Fe alloys. In both alloy systems, the exchange coupling between Fe ions increases with increasing B content. and this may be explained by the increase of the Fe-Fe separation with increasing B content. The exchange coupling between Fe and RE also increases with increasing B content. As the B content increases, the magnetization decreases over the whole temperature range, and the Curie temperature also decreases.

• Korean Journal of Environmental Agriculture
• /
• v.6 no.2
• /
• pp.53-65
• /
• 1987

The study was performed to investigate the effect of gaseous emissions of sulfur dioxide and hydrogen fluoride on the growth of rice plants under stressed field conditions consisting of 88 industrial plants operating with 285 smoke stacks emitting pollutants. As for the relationship between yields and yield components it is believed that the panicles per hill is the single most important component affecting the rate of yield of the rice plant. Based on the standard partial regression coefficient analysis, panicles per hill has the largest contribution to yield and the average contribution of 54%. Other components such as spikelets per panicle, percent fertility and 1000 grain weight are also contributing factors to yield, although far less so. Fluorine content in the leaf appear to have more negative effect on panicles per hill, percent fertility and subsequent overall yield than does sulfur content in the leaf. It is constantly observed and interesting to note that fluorine and sulfur content in the leaf appears to have no effect on spikelets per panicle and 1000 grain weight. Reduction in yield seems to be affected mainly by panicles per hill which are, in turn, affected more by fluorine content in the leaf as demonstrated by the standard partial coefficient analysis. Regarding the prediction sum of the square of the regression equation, the lowest value was found when nine variables were used for the analysis. The variables taken into consideration were the monthly sulfur and fluorine content in the leaf as well as the monthly percent of leaf damage during the months of June, July and August. A significant correlation is found between the actual and predicted yields by the regression equations selected as a result of a prediction sum of the square analysis.

• Korean Journal of School Psychology
• /
• v.8 no.2
• /
• pp.133-152
• /
• 2011

This is a short-term longitudinal study investigating the relationships between changes in mental health and academic burnout among Korean middle school students. Study sample consisted of 409 middle school students in Seoul provision, with 161 male, 216 female, and 32 unidentified. Both Symptom Check List(SCL-47) and Maslach Burnout Inventory-Student Survey(MBI-SS) were used. In order to examine the pattern of changes in mental health and academic burnout among students, standardized residuals were calculated using regression equations which were then put into canonical correlation analysis. The results of this study are as follows. First, according to Function 1, among sub-factors of mental health, decreases in depression, compulsion, anxiety, and hostility were particularly associated with decreases in exhaustion and cynicism among academic burnout. Put in another way, students who showed increases in depression, compulsion, anxiety, and hostility experienced more academic exhaustion and cynicism. Second, according to Function 2, increases in phobic anxiety, compulsion with decreases in anxiety, depression were associated with decrease in academic exhaustion and increase in cynicism. Considering Russell's dimensional theory of emotion, Function 1 showed that mental health symptoms including both aroused and non-aroused affects were related with increases in exhaustion and cynicism while Function 2 showed that mental health symptoms including only aroused aspects were related with decrease in exhaustion and increase in cynicism. Thus, a conclusive intervention program seems to be required to deal with both aroused and non-aroused affects of students who are experiencing increased exhaustion and cynicism. On the other hand, an intervention program focused on aroused affects seems appropriate to students who are experiencing decreased exhaustion and increased cynicism. This study has its value in that it has enhanced understanding of students in school and counseling settings by revealing the relationships between mental health and academic burnout among adolescents and suggested differentiated intervention strategies based on patterns of students' academic burnout.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.17 no.3
• /
• pp.33-50
• /
• 2022

While the number of female entrepreneurs has been increasing, and female entrepreneurship has been increasingly perceived as a driving force of sustainable economic development, there is a lack of studies of female entrepreneurship, particularly in the non-Western regions. This study aims to explore current levels of entrepreneurial competences of female college students in four Asian countries (i.e., Indonesia, Korea, Philippines, and Vietnam), differences in the competences between countries, and factors affecting their entrepreneurial competences. Using online surveys, the present study collected data from 516 female Asian college students and examined their entrepreneurial competences in six dimensions-entrepreneurship, sensibility, business management, relationship management, strategic management, and multi-tasking. This study also investigated effects of four variables (i.e., entrepreneurship course taking experiences, on-campus entrepreneurship experiences, off-campus entrepreneurship experiences, and entrepreneurial intentions) on the six aspects of entrepreneurial competences. Data analysis reveals that female Asian college students as a whole group possess quite high levels of entrepreneurial competences while the Filipino students show the biggest competence in all the six dimensions measured. As regards affecting factors, this study finds that, in the total sample, regression equations are significant in all the six dimensions of entrepreneurial competences. On-campus experiences have significantly positive effects on those six dimensions while course taking experiences and entrepreneurial intentions positively affect three different dimensions each. However, out-of-campus experiences turn out to be negative though their effects are insignificant. Meanwhile, in individual samples, different factors affect different dimensions of entrepreneurial competences. Based on these findings, the present study suggests some actions for promoting female entrepreneurship and for conducting future studies.