• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.443-445
• /
• 2008

Determination of allowable overtopping rate for coastal structure is a key point to determine the application of background of coastal structure while considering safety and economic efficiency. Thus, the accurate estimation of overtopping rate against coastal structure is essential. In general, estimation of overtopping against the coastal structure is based on an empirical formula or hydraulic experiment. In this study, we investigate the behavior of overtopping for rubble mound coastal structure with rubble armor stone and wave dissipating block using hydraulics experiment, and domestic or foreign design standard.

• 한국방재학회:학술대회논문집
• /
• 2009.02b
• /
• pp.125.2-125.2
• /
• 2009

• Journal of the Korean Geosynthetics Society
• /
• v.15 no.3
• /
• pp.39-47
• /
• 2016

In order to prevent leakage of leachate in offshore landfill, hydraulic barrier is indispensable. In the case of rubble mound revetment at offshore landfill, HDPE sheet in slope should be installed. In this study, seepage analysis were performed to evaluate seepage and flow in the seabed and revetment according to extended length of HDPE sheet by using SEEP/W. Results show that, in the case of low permeability layer is distributed where extended length of HDPE sheet was more than 1m, seepage flux in seabed and revetment was greatly reduced. In order to prevent seepage in seabed and revetment in the case of sand layer of high permeability is existed above low permeable layer, extended length of HDPE sheet and impermeable improvement width of permeable layer should be more than 1m at seabed.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.97-106
• /
• 2019

This study was conducted to propose a reasonable requirement regulation of barrier system of rubble mound revetment offshore landfill for preventing contaminant leakage. The barrier is composed with bottom layer and side barrier. The bottom layer was assumed as impermeable clay layer and side barrier was composed with HDPE sheet (primary element) and mid-protection layer (supplementary element). Seepage-advection-dispersion numerical analysis has been conducted using SEEP/W and CTRAN/W programs under steady flow. As the results, the minimum required barrier regulations for hydraulic conductivity and thickness of the bottom layer were suggested. For side barrier, the extended length of HDPE sheet and the hydraulic conductivity of mid-protection layer were also suggested.

• Journal of the Korean Geosynthetics Society
• /
• v.19 no.4
• /
• pp.1-9
• /
• 2020

This study analyzes contaminant movement under transient flow in a rubble mound revetment offshore waste landfill barrier system that prevents contaminant runoff. The barrier system consists of bottom layer and side barrier. For the bottom layer system, impermeable clay layer is used. For the side barrier system, the HDPE barrier sheet (primary element) plays the main role, and the intermediate protection layer (supplementary element) is responsible for the barrier. Seepage, advection, dispersion numerical analysis was carried out using SEEP / W and CTRAN / W programs. As a result, under abnormal conditions considering the fluctuation in tidal range, the volume and direction of the flow velocity vector of the pore water change with time and the dispersion concentration of the contaminant changes. When comparing the case of 2 m tidal range and 8 m tidal range, the larger the tide value, the higher the concentration of contaminant under abnormal conditions. It was found that the rate of change of the concentration of the contaminant changed depending on the change in the tidal range, and as a result, the outflow of the pollutant was smaller than that in the steady flow state.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.36 no.3
• /
• pp.105-115
• /
• 2024

In coastal structure design incorporating revetments, the assessment of wave overtopping discharge relies on hydraulic model experiments. Numerous empirical formulas have been developed to predict overtopping discharge based on quantitative data from these experiments. Typically, for revetment structures aimed at mitigating wave overtopping, crest height is determined by considering the maximum amplitude of the design wave, resulting in a relatively high freeboard compared to wave heights. However, achieving complete prevention of all wave overtopping would require the crown wall to have substantial crest heights, rendering it economically impractical. Therefore, the concept of limiting discharge has been introduced in the design of revetment structures, aiming to restrict wave overtopping discharge to an acceptable level. Consequently, many coastal structures in real-world settings feature relatively lower freeboard heights than incident wave heights. This study investigated wave overtopping discharge on rubble-mound breakwaters with relatively low freeboard heights through hydraulic model experiments. Furthermore, it conducted a comparative analysis of the predictive capabilities of existing empirical formulas for estimating overtopping discharge using experimental data.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.12
• /
• pp.141-150
• /
• 2017

Geosynthetics are generally utilized to restrain the leakage of leachate and other contaminants during the construction of offshore waste landfill. Therefore, geosynthetic-soil interface is formed inevitably. In this study, 2 dimensional numerical analysis is performed to assess the dynamic behaviour of the offshore waste landfill including geosynthetic-soil interface. Offshore waste landfill can be divided into rubble mound revetment and retaining wall types and analyzed on each type. Effective stress analysis is conducted to consider the variation of pore water pressure and axial force and shear displacement of the interface are compared based on the characteristics of seismic frequency. Consequently, retaining wall type demonstrates more stable behavior against liquefaction potential and favorable forces and shear displacement.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.3
• /
• pp.111-119
• /
• 1987

Scale effects of stability, run-up, run-down and reflection of layered coastal structures are investigated through the experiments with 7 kinds of hydraulic scale models. The occurrence mechanism and the control method of scale effects are also discussed. As a result, it is found that the similarity of permeability of inner layers plays an important role in the occurrence of scale effects, which has been neglected in the most of conventional model tests. To assure the best scale effects for permeable coastal structures, control of Reynolds numbers of the porous media flow in each layer is recommended. It is also found that Reynolds numbers in revetment, filter, and core layer must be greater than $2{\times}10^4$, $3{\times}10^3$, and $1{\times}10^3$, respectively.