• Elastomers and Composites
• /
• 제53권2호
• /
• pp.67-74
• /
• 2018

Magneto-rheological elastomers (MREs) are smart materials in which the inherent stiffness and damping properties can be changed by the influence of an external magnetic field. The magneto-rheological (MR) effect depends on the orientation characteristics of the dispersed magneto-responsible particles (MRPs) in the matrix. In this study, natural rubber (NR) and ethylene propylene diene rubber (EPDM) were blended and used as a matrix of an MRE. EPDM was pre-cured before blending with NR. The Mooney viscosity, curing characteristics, and mechanical properties were analyzed with various pre-curing conditions of EPDM and the NR/EPDM blend. The results show that excellent mechanical properties of the NR/EPDM blend-based MRE were obtained when the pre-curing time of EPDM was 60 min. The aging property of the NR-based MRE was improved by the introduction of pre-cured EPDM. Also, the anisotropic MRE showed a higher MR effect than that of the isotropic MRE.

• 항공우주시스템공학회지
• /
• 제7권4호
• /
• pp.36-41
• /
• 2013

In order to improve incombustibility of EPDM(Ethylene propylene diene monomer)-based rubber, inorganic materials as $Al(OH)_3$ and $Sb_2O_3$ were added. The mechanical and thermal properties have been measured for vulcanized rubber loaded with different concentrations of $Al(OH)_3$ and $Sb_2O_3$. As inorganic material contents increases from 5phr to 30phr, the specific gravity and hardness increase while elongation at break decreases. This study performed incombustibility test and thermal analysis through TGA(Thermogravimetric Analyzer). As a results, incombustible and thermal properties of EPDM-based rubber were improved as $Al(OH)_3$ and $Sb_2O_3$ contents increase.

• Earthquakes and Structures
• /
• 제24권3호
• /
• pp.193-204
• /
• 2023

The concept of meta-material-based isolation systems (MMIS) for structural columns has been revisited in the present study in order to enhance the stability of rubber pads by using steel shim reinforced rubber (SSRR) layers. Analytical calculations have shown a significant improvement in the stability of MMIS with SSRR pads. Finite element analysis has also been conducted to further show the reduced response of a bridge with the modified MMIS under excitations having frequencies within the corresponding attenuation zone (AZ) as compared to the response of a conventional bridge without MMIS. FE analysis further shows the stress generated on the bridge with MMIS systems are within safe limits. Finally, a generalized procedure has been developed to design bridge columns with the proposed modified MMIS.

• 한국안전학회지
• /
• 제31권1호
• /
• pp.19-24
• /
• 2016

Rubber parts are widely used in many applications such as dampers, shock absorbers, and seals used in railway and automotive industries. Much research has thus far been conducted on property estimation and life prediction of rubber parts. To predict the service life of rubber parts at room temperature, most prior work adopts the well-known Arrhenius model that needs the accelerated life test in high-temperature conditions. However, they may not reflect the actual conditions of use that rubber parts are usually used under a specific strain condition during long period of time. In this context, we propose a method for the life prediction of rubber parts in actual conditions of use. The proposed method is based on the accelerated life test using stress relaxation during which three relatively high elongation percentages (100%, 200%, and 300%) are applied to the rubber specimens. Rubber specimens were prepared in accordance with KS M 6518 standard and three stress relaxation testers were fabricated for actual experiments. Finally, a inverse power model for life prediction was derived from experimental results. The predicted life was compared with the actual test life for validation.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.21-22
• /
• 2003

4 types rubber related geosynthetics were manufactured to examine the performance to for applications to the civil and geotechnical fields, especially to the road construction. Reinforcement and water barrier function of these geosynthetics were interpreted as the important properties. Fiber glass mat based and geogrid based geosynthetics showed the excellent mechanical properties as. Also elastomeric bitumen based geosynthetic showed the highest permittivity. From this, it i s thought that this geosynthetic is suitable for water barrier under specific load condition.

• Elastomers and Composites
• /
• 제36권2호
• /
• pp.111-120
• /
• 2001

NR/NBR 혼합고무 컴파운드의 기계적 물성과 아연 및 황동피복 강선과의 접착특성에 대해 NR/NBR 조성비에 대한 함수로 조사하였다. Mooney 점도와 응력이완시간은 NBR 함량의 증가에 따라 감소하였다. NBR 함량증가에 따라 모듈러스는 전반적으로 증가하였고, 인장강도의 경우 NBR 함량이 40 phr 이하일 경우 유사한 수준을 보이다가 $50{\sim}60\;phr$일 때 최소치를 보인 후 다시 증가하는 경향을 보인 반면, 파괴점에서의 변형은 NBR 함량이 50 phr 이하의 범위에서는 선형적인 감소를 보인 후 50 phr 이후에서는 거의 유사한 수준을 보였다. NR/NBR 혼합고무 컴파운드는 NR과 NBR의 유리전이온도인 $-10^{\circ}C$와 $-55^{\circ}C$에서 탄성모듈러스의 급격한 전이와 tan ${\delta}$ 피크를 나타내 비상용성 블렌드의 거동을 나타내었다. 접착력(pullout force)과 rubber coverage 공히 NBR 함량이 증가함에 따라 급격히 감소하여 NR/NBR 혼합비가 50/50인 경우 NR 컴파운드 대비 약 40% 수준을 보였고, 순수한 NBR 컴파운드의 경우 접착력은 다시 증가하여 NR 컴파운드 대비 약 90% 수준의 접착력을 보였다. Auger spectrometer 분석결과 NBR 함량이 증가할수록 황함량이 감소하였고, 이는 강선-고무간 접착계면에서 접착층이 충분히 성장하지 못했다는 것을 의미하고 접착성능 하락의 원인으로 해석하였다.

• Advances in concrete construction
• /
• 제9권3호
• /
• pp.249-256
• /
• 2020

This paper aims at investigating the effect of crumb rubber size and content on compressive behaviors of concrete under axial compression. Concrete specimens are designed and produced by replacing natural aggregate with crumb rubber content of 0%, 5%, 10%, 15% and three different sized crumb rubbers (No. 20, No. 40, No. 80 crumb rubber). And the failure mode, compressive strength, elastic modulus, stress-strain curves, peak strain and ultimate strain are experimentally studied. Based on the test results, formulas have been presented to determine the compressive strength, elastic modulus, the relationship between prism compressive strength and cube compressive strength, stress-strain curves and peak strain of crumb rubber concrete (CRC). It is found that the proposed formulas agree well with the test result on the whole, which may be used to practical applications.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.17-23
• /
• 2006

Rubber materials have the nonlinear, large deformation and viscoelastic behavior. W.D. Kim et al. studied these characteristics through the static, fatigue, dynamic, aging and viscoelastic test. This paper discussed that the properties of engine mounting rubber, such as static stiffness, fatigue life and damping factor, are predicted based on CAE by using material properties acquired by the report of Kim et al. In result, the static stiffness of engine mounting rubber is predicted approximately in comparison with test value. Also, it was confirmed that the relationship of fatigue life and Green-Lagrange strain in specimen was the valid tool to predict the fatigue life of engine mounting rubber. From the results of transient viscoelastic analysis the damping factor changed rapidly at the range less than 8hz.

• Macromolecular Research
• /
• 제15권4호
• /
• pp.315-323
• /
• 2007

The present manuscript deals with the prediction of the lifetime of NBR compound based rubber gaskets for use as fuel cells. The material was investigated at 120, 140 and $160^{\circ}C$, with aging times from 3 to 600 h and increasing $H_2SO_4$ concentrations of 5, 6, 7 and 10 vol%. Both material and accelerated acid-heat aging tests were carried out to predict the useful life of the NBR rubber gasket for use as a fuel cell stack. To investigate the effects of acid-heat aging on the performance characteristics of the gaskets, the properties of the NBR rubber, such as crosslink density and elongation at break, were studied. The hardness of the NBR rubber was found to decrease with decreasing acid concentration at both $120\;and\;140^{\circ}C$, but at $160^{\circ}C$, the hardness of the NBR rubber increased abruptly in a very short time at different acid concentrations. The tensile strength and elongation at break were found to decrease with increases in both the $H_2SO_4$ concentration & temperature. The observed experimental results were evaluated using the Arrhenius equation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.653-657
• /
• 2000

The paper describes the contents and results of the national project named "Development of Computer Integrated Product Design for Automation Equipment". It is focussed on the real-time control '||'&'||' monitoring of manufacturing process for automobile rubber parts. Automobile rubber parts industy is one of the typical process that high11 depends upon manufacturing facilities and equipments. So. it requires high cost and engineering technolog) on plant implementation. But most companies of rubber parts industries are small or mid companies that habe weak abilities for plant implementation properly and systematically. Therefore, for upgrading the levelof automation. it is necessar). to dekelope the computer based management and monitoring slsteni that enables to build-up the common base of automation and systemization. 'Through this project. we developed low cost real-time monitoring system for banbun mixing process '||'&'||' mold injection process of rubbcr parts manufacturing, that is composed with DDCU(Distributed Digital Control Unit),signal interfaces to gathering mon~toring terms and speciall\ developed functional sofhare including some algorithm for management '||'&'||' process monitoring