• Elastomers and Composites
• /
• v.6 no.1
• /
• pp.53-70
• /
• 1971

We have studied the blending effects of cis-1,4-polybutadiene (CBR) and styrene-tutadiene rubber at various blending ratios of 100 : 0, 70 30, 50 : 50, 30 : 70, 0 : 100, and of carbon black ISAF and HAP at various compounding ratios of 45 PHR, 55 PHR, 65 PHR, for tyre tread rubber. The results obtained are summerized as follows; 1. For tyre tread rubber, it was found to increased efficiency to use SBR polymer only than to use the blending ratio CB/SBR=30/70 below. But it was observed that the latter was adapted for the bus or truck tyre and the former for the passenger tyre. 2. Excellent efficiency was obtained in case of carbon black compounding ratio of 55%, and also the compounding of ISAF made better efficiency than that of HAF. 3. Carbon black was more efficient to SBR than to CB. 4. For the aging ratio, the compounding rubber of NR was the highest, and the ratio was decreased in order of the compounding rubber of oil-extended SBR or CB polymer only, the compounding rubber of non oil-extended SBR or CB polymer only, and the blending rubber.

• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.55-58
• /
• 2007

Thermal Characterization of an EPDM/IIR rubber blend was performed using TG/DTG analysis. While TGA thermograms of a virgin EPDM and IIR showed their own characteristic thermal decomposition curves, that of an EPDM/IIR blend sample showed a characteristic curve, exhibiting both decomposition characteristics of EPDM and IIR. This finding was more clarified from DTG analysis obtained by differentiation of TGA thermograms, being exhibited as two distinct shifted-peaks. Degrees of peak-shift (${\Delta}T$) compared to their original positions were $+25\;^{\circ}C$ for IIR and $-15\;^{\circ}C$ for EPDM, respectively. From these facts, thermal stability of EPDM is considered comparatively better than IIR, and moreover, it can be an evidence for the characteristics of a partial compatibility between EPDM and IIR. It is noteworthy that, if we prepare in advance a calibration curve for the composition about EPDM/IIR blend, it may be possible to analyze quantitatively an EPDM/IIR blend, using comparatively simple TGA experiments as in the present work.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.111-120
• /
• 2001

Mechanical properties and their adhesion behavior with zinc- and brass-plated steel cords of natural rubber/acrylonitrile-butadiene blend compounds were investigated as a function of blend ratio. The Mooney viscosity and stress relaxation time were found to be lowered with increasing NBR content. Tensile modulus generally increased with increasing NBR content. Tensile stress at break stayed constant up to about 40 phr and showed minimum at $50{\sim}60 phr$, and thereafter increased with increasing NBR content. Strain at break decreased linearly below 50 phr, and above the level it showed nearly constant value. Based on the abrupt drops in elastic modulus and tan ${\delta}$ peak, the glass transition temperature of NR and NBR were found to be -55 and $-10^{\circ}C$, respectively. In the case of NR/NBR blend compounds, two distinct transition points were observed and each transition position was not affected by NBR level indicating an incompatible nature of NR/NBR blend system. The pullout force and rubber coverage decreased to the level of about 40% to that of pure m compound, when the 50 phr of NR was replaced by NBR. However, the pure NBR compound showed the comparable adhesion performance with NR(${\sim}90%$). The sulfur concentration was found to become lower with the increased NBR content at the adhesion interface based on the Auger spectrometer results, representing a lack of adhesion layer formation, and this was explained for a possible cause of low adhesion performance with adding NBR.

• Elastomers and Composites
• /
• v.6 no.2
• /
• pp.73-79
• /
• 1971

As a series of the studies of EPDM-Polymer blends, the experiments are concentrated to the investigation of the physical properties of the EPDM-SBR blends. The results are shown as follows: 1. Tensile strength decreased with increase in EPDM contents and the decreasing value was good results than NR blending. 2. It was found that the aging were much improved after blending and experiments data was good results than NR blending.

• Elastomers and Composites
• /
• v.33 no.3
• /
• pp.193-200
• /
• 1998

It is well known that EPDM(ethylene propylene diene monomer) rubber has inherently excellent resistance to the weathering, ozone, heat, cold and moisture, whereas crosslinked IIR (isobutylene isoprene divlnyl benzene terpolymer) shows proper resistance to the water and gas permeation. Various characteristics of EPDM blend with crosslinked IIR such as curing characteristics, mechanical properties, dispersion of minor component and gas impermeability were explored. The optimum curing time $(t_{90})$ examined with peroxide was decreased by adding small amount of crosslinked IIR to the EPDM rubber. Mechanical properties of blends such as tensile strength, hardness and elongation at break were enhanced by increasing EPDM content. These results might be explained with the affinity of carbon black to the EPDM rubber. On the other hand, the physical properties were not changed significantly after aging, and the increase of crosslinked IIR fraction caused the decrease of compression set to small rate. EPDM rubber shows different behavior with crosslinked IIR in oxygen permeability. By adding 30wt.% crosslinked IIR to the EPDM rubber, the resistance to the oxygen permeation was improved up to three times than that of pure EPDM rubber. Conclusively, EPDM blend containing 30wt.% crosslinked IIR might be commercially applied to the o-ring and electric parts because of its proper resistance to the weathering, ozone and oxygen permeability.

• Journal of Environmental Science International
• /
• v.9 no.6
• /
• pp.511-515
• /
• 2000

The purpose of this experiment is to prepare ethylene propylene diene terpolymer(EPDM)/ acrylonitrile butadiene rubber(NBR) blend which represents good environmental resistant properties including favorable oil and ozone resistance. With incorporation of EPDM, NBR and other ingredients, the rubber and chemical additives were mixed by mechanical method such as Banbury mixer and open 2-roll mill. Then rubber vulcanizates were manufactured by hot press and mechanical properties, oil and ozone resistance of the test specimens were measured. The oil resistance and ozone resistance of EPDM and NBR, respectively, is remarkably improved by blending EPDM with NBR. The optimum results of oil and zone resistant characteristics were obtained at EPDM/NBR(=25/75 wt%) composition ratio.

• Elastomers and Composites
• /
• v.6 no.2
• /
• pp.47-63
• /
• 1971

We have studied the blending effects of Diene 33R and styrenebutadiene rubber at various blending ratios of 100/0, 70/30, 50/50, 30/70, 0/100, and of carbon black HAF and ISAF at various compounding ratios of 55 PHR, 65 PHR, 75 PHR for tyre tread rubber. As the results, it was found that ; 1. For tyre tread rubber, when the blending ratio, Diene NF 35R/SBR 1778, indicated 30/70, the physical properties we examined were most excellent. 2. Excellent result was obtained in case of carbon black compounding ratio of 65 PHR. The compounding of ISAF made better result than that of HAF for abrasion quantity, tearing strength, and tensile strength. 3. Heat buildup obtained from compounding carbon black HAF indicated low temperature than that from compounding carbon black ISAF. As the compounding amount of carbon black increased, the heat buildup improved. And as the blending amount of Diene NF 35R decreased, the heat buildup dropped. 4. Carbon black was more efficient to SBR than to Diene Rubber. 5. It is a shortage that elongation revealed low price.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.255-266
• /
• 1998

One-step continuous reactive blend with EPDM is investigated using a modular intermeshing corotating twin screw extruder This was performed via anionic polymerization mechanism. Mechanical properties were characterized and compared with mechanical blends.

• Elastomers and Composites
• /
• v.32 no.4
• /
• pp.268-275
• /
• 1997

• Elastomers and Composites
• /
• v.8 no.1
• /
• pp.12-25
• /
• 1973