• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4220-4225
• /
• 2022

Monte Carlo (MC) simulations are increasingly being used as an alternative or supplement to the gamma spectrometric method in determining the full energy peak efficiency (FEPE) necessary for radionuclide identification and quantification. The MC method is more advantageous than the experimental method in terms of both cost and time. Experimental calibration with standard sources is difficult, especially for specimens with unusually shaped geometries. However, with MC, efficiency values can be obtained by modeling the geometry as desired without using any calibration source. Modeling the detector with the correct parameters is critical in the MC method. These parameters given to the user by the manufacturer are especially the dimensions of the crystal and its front edge, the thickness of the dead layer, dimensions, and materials of the detector components. This study aimed to investigate the effect of the front edge geometry of the detector crystal on efficiency, so the effect of rounded and sharp modeled front edges on the FEPE was investigated for <300 keV with three different HPGe detectors in point and volume source geometries using PHITS MC code. All results showed that the crystal should be modeled as a rounded edge, especially for gamma-ray energies below 100 keV.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.48-54
• /
• 2007

Surface of rapid prototype has inevitably stair-stepping error, which is attributed to the continuous building process of 2 dimensional area. In this study, rounded edge model was established to estimate the roughness of inclined surface which has stair-stepping error. To investigate the roughness of rapid prototypes, specimens that have various surface inclinations were manufactured by various types of RP machines. As the surface inclination increased, the roughness of the specimens manufactured by SL, FDM, or LOM process decreased, which coincides with the simulation results. However, surface roughness of 3DP specimen was almost independent of the inclination. Furthermore, as the angle of surface increased, roughness of poly-jet specimen also increased, which is attributed to the frictional behavior between writing head and scanned area.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.85-92
• /
• 2001

The variation of contact traction induced by different contact shapes is studied experimentally and theoretically. Considerations fer the contact shape are rounded, truncated and truncated with rounding punches. A fretting wear experiment is conducted with the contact configuration of the strip on the tube specimens. The strip specimen is pressed to form the end profile of a rounded and truncated with rounding punches shape. Wear on the tube is investigated, which is regarded as the slip region of the contact surface. Taken into consideration is the general solution of the normal traction in the case of the indentation by a punch with its end profile of the combination of parabolas. Then, partial slip solution is obtained numerically, which is compared with the wear on the tube. The radius of the rounding and the obliquity of the edge truncation affect the tractions considerably. It is found that the proper choice of the end profile can restrain the contact-induced failure such aswear.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.4
• /
• pp.405-420
• /
• 2003

Purpose : The purpose of this study was to compare the fracture resistance of the IPS Empress ceramic crown with 1.0mm width rounded shoulder, which is usually recommended in all ceramic crown. and 0.5mm width chamfer finish lines on the maxillary central incisor. Material and method : After 15 metal dies were made for each group, the IPS Empress all ceramic crowns were fabricated and cemented with resin cement(Bistite resin cement, Tokuyama Soda Co. LTD., Japan) on the metal die. The cemented crowns were mounted on the positioning jig and the universal testing machine(Zwick Z020, Zwick Co. Germany)was used to measure the fracture strength with loading on the incisal edge. And also, three-dimensional finite element stress analysis was used to measure the stress distribution with the various types of the finish lines(1.0mm width rounded shoulder, 0.5mm width chamfer), the loading site(incisal edge, incisal $\frac{1}{3}$) and the type of loading(concentration loading, distribution loading). Results and conclusion : 1. In the fracture resistance experiment according to the finish line, the mean fracture strength of rounded shoulder(876N) and the mean fracture strength of chamfer(882N) did not skew any significant difference between each other(p>0.05). 2. The stress distribution of all ceramic crown in three dimensional finite element analysis showed concentration aspect at loading point and cervical area or labial surface. 3. In metal die, there were no differences in stress distribution between finish lines, but in natural teeth model, chamfer finish line showed higher stress than rounded shoulder finish line. 4. When force was loaded on the incisal edge the stress was concentrated on the incisal edge and the cervical area of labial surface. When force was loaded on the incisal $\frac{1}{3}$, the stress concentrated on the cervical area of labial surface and the cingulum area. 5. Generally, natural teeth model showed higher and various stress than the metal die.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.22 no.1
• /
• pp.17-25
• /
• 2016

Purpose: This study was aimed to determine the effects of thoracic spine thrust manipulation on muscle activities of the scapular upward rotators and middle deltoid, active range of motion (AROM), shoulder pain, and rounded shoulder posture in young adults with rounded shoulder. Methods: The subjects were 30 young adults (14 males, 16 females) with rounded shoulder. Thirty subjects were randomly assigned to an experimental (manipulation) and control (placebo) groups of fifteen subjects respectively. The manipulation group received the manipulation (high velocity, low amplitude), which was performed by a physical therapist with the subject in the supine position and with the arms crossed over the chest and hands passed over the shoulders. For the sham group, the same procedure was performed, with the exception that the high-velocity thrust was not applied. Measurements were taken before and after the intervention. Muscle activity of upper and lower trapezius, serratus anterior, middle deltoid was measured using surface electromyography. Visual analog scale (VAS) was used for shoulder pain. Goniometry was used for shoulder abduction active range of motion (AROM). Straight edge was used for supine rounded shoulder posture (RSP) distance. Results: The muscle activity of the upper trapezius, lower trapezius and middle deltoid muscle increased significantly after the intervention (p<.05). However, no significant difference was observed in serratus anterior muscle (p>.05). The VAS was significantly decreased and AROM significantly increased after the intervention (p<.05). The distance of RSP were not significant (p>.05). The control group showed no differences before and after the intervention (p>.05). Conclusion: The results of this study suggest that thoracic spine thrust manipulation can be an effective component of treatment plan to improve pain and function.

• Journal of Korean Society of Steel Construction
• /
• v.28 no.5
• /
• pp.355-363
• /
• 2016

This study numerically investigates buckling behavior of press braked steel plates with a free edge that consists of the upper flange of U-shaped box girder. Since the press-braked plates include a rounded edge, the effective width to thickness ratio of the press-braked upper flange is obscure to determine the nominal compressive strength. This study performed 3D finite element analyses to evaluate an equivalent effective width of cold-formed plate with a free edge. Through the parametric numerical analyses, the elastic buckling stresses of the rounded corner plates were compared with those of general flat plates and then, the equivalent effective width has been estimated. A comparative study with Euler buckling formula speculated in the domestic design specifications has been conducted.

• Journal of Aerospace System Engineering
• /
• v.13 no.5
• /
• pp.32-38
• /
• 2019

The flying wing configuration with high sweep angles and rounded leading edge represent a complex flow of structures by the leading edge vortex. For control of the tailless flying wing configuration with unstable directional stability, flaperon is used. In this study, we conducted numerical simulations for a non-slender flying wing configuration with a rounded leading edge and analyzed the effect of the sideslip angle and flaperon. Through aerodynamic coefficient analysis, it was found that the effect of AoS on lift and drag coefficient was minimal and the side force and moment coefficient were markedly influenced by AoS. As the sideslip angle increased, the pitch break, which is related to the pitching moment coefficient, was delayed. Through stability analysis, the directional and lateral static stability of the flying wing configuration were increased by flaperon. Also, the structure and behavior of the leading edge vortex were analyzed by observing the contour of the pressure coefficient and the skin friction line.

• Journal of Ship and Ocean Technology
• /
• v.8 no.2
• /
• pp.13-19
• /
• 2004

Jet flows applied tangential to a foil surface near the leading and/or trailing edges increase the lift of the foil by delaying the separation also known as the Coanda effects. Many experimental and numerical studies have proven the effectiveness of Coanda effects on circulation control and the effects have been found to be useful in practical application in many aerodynamics fields. Most of the previous works have studied the effects of the jet blowing near the trailing edges and investigated the influence of jet momentum on lift. A few experimental studies, however, focused on the separation bubble that develops near the leading edge and applied jet flow the edge to remove the bubble but only to find decrease in lift. In the present paper, a Coanda foil of 20% thickness ellipse with modified rounded leading and trailing edges was investigated, and the flow around the foil was numerically studied. The blowing around the leading edge only decreased the lift, as the experiments showed, but the suction considerably increased the lift.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.1
• /
• pp.53-61
• /
• 1996

A clear understanding of the surface formation mechanism due to cutting is very important to help produce a good quality surface. Much of the roughness along the length of a bar being cut in a lathe can be explained in terms of macroscopic tool shape and feed rate. However, the roughness along the direction of cutting requires a different explanation. The formation of surface roughness is a problem in flow and fracture of materials in the vicinity of the tool edge. On a microscopic scale the cutting edge is rounded because it is impossible to grind a perfectly sharp cutting edge. Even if a perfectly sharp cutting edge were obtained it would soon become dull as a result of rapid breakdown and wear of the cutting edge. A research project is proposed in which in the main object is to model the surface formation mechanism due to cutting. The tool was assumed to be dull, that is, its edge has a finite radius. In order to study the effect of the radius of cutting edge on the surface formation, tools having different cutting edges were used. For orthogonal cutting experiment, cast iron and glass were chosen as brittle materials. Plowing forces acting in the cutting edge were estimated and its effect on the surface roughness was studied by observing the machined surface using optical microscope.