• 대한기계학회논문집B
• /
• 제22권12호
• /
• pp.1735-1745
• /
• 1998

Oil-film surface flow visualizations and three-dimensional flow measurements using a straight five-hole probe have been conducted for a circular impinging jet which is normally oriented to the crossflow in a channel. Throughout the experiments, the ratio of channel height to injection hole diameter, H/D, is fixed to be 1.0, and blowing ratio is varied to be 1.0, 2.0, 3.0 and 4.0. From the surface flow visualizations for both top wall(target plate) and bottom wall, impinging jet region on the target plate can be clearly identified, and for the small value of H/D = 1.0, presence of the bottom wall changes the near-hole flow structure, significantly. The three-dimensional flow measurements show that in the dawnstream region of the injection hole, there exist a pair of counter-rotating vortices, called "scarf vortices", and the strength of the vortices strongly depends on the blowing ratio. In addition, a new flow model in the flow symmetry plane has been proposed for H/D = 1.0.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권4호
• /
• pp.437-442
• /
• 1997

An experimental study was carried out in a channel cavity with square heat surface by visual¬ization equipment with Mach - Zehnder interferometer and laser apparatus. The image processing system consists of one commercial image board slit into a personal computer and 2-dimensional sheet light by Argon-Ion Laser with cylindrical lens and flow picture recording system. Instant simultaneous velocity vectors at whole field were measured by 2-D PIV system which adopted two¬frame grey-level cross correlation algorithm. Heat source was uniform heat flux(o.4W/cm$^2$, , O.8W/cm$^2$, 1.2W/cm$^2$). Obtained result showed various flow patterns such as kinetic energy distribution. Severe unsteady flow fluctuation within the cavity are remarkable and sheared mixing layer phenomena are also found at the region where inlet flow is collided with the counter-clockwise rotating main primary vortex. Photographs of Mach ~ Zehnder are also compared in terms of constant heat flux.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.816-821
• /
• 2003

The pumping characteristics of a disk-type drag pump (DTDP) from free molecular flow region to the slip flow region are calculated by the direct simulation Monte Carlo (DSMC) method. In this study, the pumping performance is studied numerically for several channel depths. The interaction between molecules is modeled by variable hard-sphere (VHS). The no time counter method is used as a collision sampling technique. The clearance between rotor and stator is considered an effect on performance. Spiral channels are cut on both upper and lower sides of rotating disks, and stationary disks are planar. A three-dimensional DSMC method for the analysis of steady rarefied flows in a single-stage DTDP has been developed. Velocity and density fields were obtained by the DSMC simulation in the rotor. The present experimental data in the outlet pressure range of $7.5{\times}10^{-3}{\sim}4$ Torr were compared with the DSMC results in the single-stage DTDP. Comparison between the experimental data and DSMC results showed good agreement.

• 대한기계학회논문집B
• /
• 제26권2호
• /
• pp.261-268
• /
• 2002

Turbulent flow past a square cylinder confined in a channel is numerically investigated by Large Eddy Simulation(LES). The main objectives of this study are to verify the experimental results of Nakagawa et al.[Exp. in Fluids, Vol. 27, 3, pp. 284∼294, 1999] by LES and to obtain related flow information in detail. The LES results obtained are in excellent agreement with the experiment both qualitatively and quantitatively. The passive paticles numerically released into the flow field clearly show the barman vortex street. However, the vortices shed from the cylinder are significantly affected by the presence of the plates. Futhermore, periodic and alternating vortex-rollups are observed in the vicinity of the plates. The rolled-up vortex is convected downstream together with the corresponding Karman vortex forming a counter-rotating vortex pair. It is also revealed that the cylinder greatly enhances mixing process of the flow.

• 한국해양공학회지
• /
• 제12권1호
• /
• pp.113-119
• /
• 1998

An experimental study was carried out in a three-dimensional cubic cavity driven by 2-dimensional plane Poiseuille flow for three kinds of Reynolds number, $10^4$, 3 $\times$ $10^4$ and 5 $\times$ $10^4$ based on the cavity width and cavity inlet mean flow velcoity. Instant simultaneous velocity vectors at whole field were measured by 2-D PIV system. Laser based illumination and two-frame grey-level cross correlation algorithm are adopted. Severe unsteady flow fluctuation within the cavity are remarkable at above Re = 3 $\times$ $10^4$ Reynolds numbers and sheared mixing layer phenomena are also found at the region where inlet driving Poiseuille flow is collided with the clock-wise rotating main primary vortex at upper center area. Instant velocity profiles reveal that deformed forced vortex formation is observed throughout the separate two areas.

• 전기전자학회논문지
• /
• 제13권2호
• /
• pp.220-223
• /
• 2009

A simple measurement system is built to estimate the dual-antenna diversity gain at 2.4GHz easily in open lab environment. To obtain multipath fading propagation channel, the system consists of two transmission horn that placed on opposite direction and a rotating stage mechanically changing the position of test dual-antenna with time over distance greater than one wavelength. Estimated diversity is nearly same as theoretical value such that measured diversity gain of 30mm separated is about 6dB similar to theoretical value of 5.7dB and increases monotonically with the increasing separation distance as predicted by the theory. Proposed measurement system that is simple enough to fit in a small space can evaluate the performance of various dual-antennas with a reasonable accuracy with lower 5% difference between the ten sets of measured waveform distribution and theoretical Rayleigh cumulative distribution.

• 소음진동
• /
• 제6권3호
• /
• pp.325-332
• /
• 1996

One of the greatest shortcoming in today's predictive maintenance program is the ability to diagnose the mechanical and electrical problems within the machine when the vibration exceeds preset overall and spectral alarm levels. In this study, auto-diagnosis system is constructed by using A/D converter to convert analog to digital singal. With this device the system analyses input signal to diagonosis machine condition. Many plots, which display machine condition, and input values of every channel are calculated in this system. If the falut is found, the system diagnoses automatically using fuzzy algorithm and trend monitoring. Prediction is also performed by the grey system theory. Operator finds out eh machine operating condition intuitively based on with personal computer CRT in using this system.

• 대한기계학회논문집
• /
• 제9권2호
• /
• pp.181-189
• /
• 1985

본 연구에서는 단순유로인 단면이 장방형인 각통을 그것에 수직한 축둘레에 회전시켜서 유로의 압력측 및 부압측에서의 속도 및 변동속도성분의 거동을 실험적으 로 조사함으로서 코리올리힘이 난류경계층 내의 유동에 미치는 영향을 구명하였다.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.88-93
• /
• 2012

This paper describes the machinability of the sintered carbide and tool-die steel(STD-11) by electric discharge drilling with various tubular electrodes which have multi-holes. Various types of electrode which have different diameters and materials are used with the application of continuous direct current and axial electrode feed. Inner part of electrodes are inserted with smaller tubes or Y-channel or bar. In ED-Drilling, the dielectric flushed down the interior of the rotating tube electrode, in order to remove machining debris from the hole. As result of experiments, the bigger the diameter of the electrode is, the lower the material removal rate is. Machinability of copper electrode is higher than that of brass. In machining of sintered carbide, to use oil is better than distilled water as dielectric.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.573-580
• /
• 2002

Animation and time-resolved analysis of the wake characteristics of 2-D bluff body flows were examinated by applying the multi-vision PIV to square cylinders(three angles of attack: $0^{circ}, 30^{circ} and 45^{\circ}$) and circular cylinders(three rotating speeds: 0rpm, 76rpm, 153rpm) submerged within a circulating water channel $(Re=10^4)$, The macroscopic shedding patterns and their dominant frequencies were discussed in terms of instantaneous velocity, vorticity and turbulent quantities such as turbulent intensity, turbulent kinetic energy and three Reynolds stresses. Particularly the time-averaged distribution of turbulent intensity 'islands' where their peak magnitudes were focused always small regions behind the bodies without noticeable spatial migration were particularly discovered in all cases. And the dominant frequencies of the turbulent quantities in the wake regions were two times larger than those of the velocity and vorticity.