• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.1206-1212
• /
• 2003

Shell vibrations of the rotary compressor, which account for considerable portion of the noise from compressor, are caused by various sources. Among them is the vibration of the in nor part or cylinder assembly, which undergoes severe compression process and rotational motion. But little researches have been carried out about the behavior and effect of the inner part because of its structural complexity. Furthermore, the shell of the rotary compressor is hermetic type that experimental approach is very difficult. This research studied the structure-born noise of the Rotary compressor using FE an analysis. The comparison between sound pressure spectrum and natural frequencies of the shell vibration implies that shell vibrations contribute significantly to the noise. It is found that inner part vibrations are responsible for those through the FE analysis. Design modification of the inner part, which shifts the target frequencies, reduced overall noise level of the compressor.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.113-118
• /
• 2008

For a R134a rotary vane compressor used for car air conditioners, characteristics of gas compression and oil supply have been studied. The compressor model under investigation has the low volume ratio of suction to discharge volumes so that there occur flow reversal from discharge port to compression chamber as the leading vane passes over the discharge port. As a result, the volumetric and adiabatic efficiencies turn out to be relatively low compared to other types of displacement compressors. Oil supply mechanism has been comprehended for mathematical modeling and oil flow rate has been calculated for the individual oil passages. This study on the gas compression and oil supply of a rotary vane compressor can be applied to a future design practice on a similar type of compressor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.74-82
• /
• 2010

Fretting damage can be observed in automobile and railway vehicle, fossil and nuclear power plant, aircraft etc. In the present study, railway axle material RSA1 used for evaluation of fretting fatigue life. Plain and fretting fatigue tests were carried out using rotary bending fatigue tester with proving ring and bridge type contact pad. Through these test, the following results are obtained: 1) it is found that the fretting fatigue limit of standard specimen decreased about 37% compared to the plain fatigue limit. 2) The early crack of Shinkansen type specimens initiated in contact area and final fractured below samp=214 MPa. 3) The early crack of all TGV type specimens initiated in rounded area and fractured. 4) Tire tracks and rubbed scars were observed in the oblique crack region and fatigue crack growth region of fracture surface. 5) The wear debris is observed on the contact surface, and oblique cracks at an earlier stage are initiated in contact area. These results can be used as useful data in a structural integrity evaluation of railway axle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.3
• /
• pp.104-111
• /
• 2019

A separate type rotary engine consisting of a compressor and an expander is under development. The engine motoring, compressor pressure, and fuel combustion have been tested with the initial prototype for operability checks of the mechanism. This paper describes an engine cycle analysis method designed specifically for this new-concept engine. The unique operational mechanism of the engine and the thermodynamic properties of each step of air intake, compression, filling of combustion chamber, combustion, expansion and exhaust were analyzed. The cycle efficiencies of this engine according to various engine design parameters as well as the cooling effect of compressed air between the compressor and expander can be easily calculated with this method; further, some case studies are presented in this paper.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.321-321
• /
• 2010

In this paper, we propose a novel type shaft-less ring type ultrasonic motor. A traveling wave rotary type ultrasonic motor is selected as a base model. The newly designed stator has two piezoelectric ceramic rings which are bonded in sandwich shape as traveling wave generator. So, we can expect to produce higher torque. The proposed model has the rotor structure that coupled with the stator provokes the pressure, this model do not install the separate plate any spring device. We used the finite element method to verify the operation principle and to compute the vibration mode of proposed model.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.10
• /
• pp.433-437
• /
• 2005

This paper studied Rotary type ultrasonic motor which has cross type stator. The stator consists of hollowed cross type metal which has four piezoelectric ceramics on the ends of cross bars. When two harmonic voltages which have 90$^{\circ}$ phase difference given to ceramics, the elliptical motion was generated in the inside tips. Inside tips are contact with rotor and these elliptical motions are rotate the rotor The finite element analysis was used to optimize the dimension and displacement of the stator. And the analyzed results were compared with the experimental results of the motor. As results, the speed and the torque of motor was increased by increasing width of the cross bar. And the speed and torque o( motor was not influenced to length of cross bar. The speed and torque was linearly increased by increasing voltage. The maximum torque was generated when the motor fabricated length of cross bar and width of ceramics in the ratio of 1:2.

• Proceedings of the Korean Society of Tobacco Science Conference
• /
• 2003.10a
• /
• pp.21-21
• /
• 2003

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.11
• /
• pp.771-778
• /
• 2015

In this work, vibration characteristics of high speed rotary bell cup for paint atomizer are numerically investigated. New type of bell cup model is proposed and additional corresponding models with design parameter variations for length and diameter are constructed. Dynamic characteristics, such as natural frequencies and corresponding mode shapes, are studied for each model as a first step. To investigate operation stability, critical speed of rotary bell cup is numerically analyzed based on Campbell diagram and separation margin between operating speed and critical speed is identified. Unbalance vibration responses are also investigated with respect to design parameter variation, operating speed and balancing quality grade of G. Then the proper design guideline for stable operation of high speed rotary bell cup for paint atomizer is suggested.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.2
• /
• pp.96-105
• /
• 2001

R410a which is one of HFC refrigerants is being considered to be a promising replacement for R22 widely used in domestic air conditioners. The rolling piston type rotary compressors for R410a have lower energy efficiency than those for R22 because of the high pressure difference between a suction chamber and a discharge chamber in the compression mechanism. in addition, the re-expansion gas loss of the rotary compressor for R410a which occurs a ta clearance volume in a discharge port becomes larger than that for R22 due to high density of R410a refrigerant. Therefore, Pressure-Volume analyses for various design parameters of a discharge system were carried out to improve efficiency of a R410a rotary compressor. The results such as performance dta, over-compression loss, and re-expansion loss were acquired by P-V analyses and analyzed quantitatively. As a conclusion, the optimal specifications of several design parameters of a discharge system were obtained by analyzing P-V diagrams.

• Journal of the Korean Society for Railway
• /
• v.20 no.2
• /
• pp.196-202
• /
• 2017

A very long test track is required for high-speed operation test of the real-scale Linear Synchronous Motor (LSM) for ultra-high-speed trains. The required length results in huge construction cost and economic loss if any error occurs during development. Therefore, validation study of the LSM design technology using a low-cost small-scale model must be carried out in the early research stages. It is possible to deduce an optimal winding method for the armature and determine the mechanical properties of the LSM through a performance tester that applies a rotary-type small-scale LSM model. In addition, it is possible to utilize previous research on LSM control systems. Therefore, a basic design model, comprising a rotary-type LSM tester that meets the requirements for the propulsion of 600km/h-class ultra-high-speed trains, is derived in this study. Finally, an optimal model, which has a stable structure under the condition of 1500rpm or more high-speed rotation, is derived by electromagnetic and mechanical stiffness analysis.