• 동력기계공학회지
• /
• 제9권4호
• /
• pp.51-57
• /
• 2005

In order to prevent the environmental pollution, the dryers are commonly used to treat sludge that one of sewages is polluting the quality of water. Generally, the drying method is various as to the property of material and use. Rotary dryer is a good apparatus to treat them. The rotary dryer is the way that is to make substance transmission and heating using hot air between sludge particles and heated gas. In this paper, we performed a numerical analysis of the inner air flow of the 3-pass rotary dryer through the changing rotational speed from 3rpm to 10rpm. In this result, we found that 3rpm is effective to dry material in terms of heat transfer because large scale velocity fluctuation is occurred inside the first and second drum. Also we confirmed that 5rpm and 8rpm showed up uniform flow at the center area of the first drum.

• 한국안전학회지
• /
• 제32권5호
• /
• pp.129-134
• /
• 2017

This study aims to develop the traffic accident models by circular intersection type using count data model. The number of accident, the number of fatal and injured persons(FSI), and EPDO are calculated from the traffic accident data of TAAS. The circular intersection accident models are developed through Poisson and negative binomial regression analysis. The main results of this study are as follows. First, the null hypotheses that there are differences in the number of traffic accidents, FSI and EPDO by type of circular intersections are rejected. Second, the scale of intersection(median, large), number of approach road, mean width and length of exit road, area of the circulating roadway and central island are selected as factors influencing the number of traffic accidents, FSI and EPDO in rotary. Third, the scale of intersection(median), guide signs(limited speed, direction, roundabout), number of approach road, entry angle, area of the intersection and central island are adopted as factors influencing the number of traffic accidents, FSI and EPDO in roundabout. Finally, transferring from rotary to roundabout could be expected to make the accident decrease.

• 제어로봇시스템학회논문지
• /
• 제11권3호
• /
• pp.228-232
• /
• 2005

This paper presents the efforts of the studies for improvement of spin characteristics of KTX-1 #02 through rotary balance test, forced oscillation test and spin mode analysis. During the full scale development design stage, we had fullfilled a lot of spin flight test, spin mode analysis. Based on all of the efforts, KTX-1 had been developed as a successful trainer with excellent spin characteristics.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.607-612
• /
• 2001

Rotary ultrasonic motors are based on the traveling wave generated by piezo materials attached on the stator. Large scale model of an annular ring was built to understand the fundamental mechanism involved in the rotary ultrasonic motors. Traveling wave on the structure can be generated by superposing two standing waves. Precise matching of the amplitudes and phase shift between two standing waves in time and space is the key to the success of generating a traveling wave.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2270-2276
• /
• 2002

Dynamic stability of a rotary oscillating cantilever beam is presented in this study. Using the stretch deformation instead of the conventional axial deformation, three linear partial differential equations are derived from Hamilton's principle and transformed into dimensionless forms. Stability diagrams of the first order approximate solutions are obtained by using the multiple scale perturbation method. The stability diagrams show that relatively large unstable regions exist near the combination of the first chordwise bending natural frequency and the first stretch natural frequency. This result is verified by using the generalized -$\alpha$ method.

• 한국정밀공학회지
• /
• 제19권11호
• /
• pp.160-166
• /
• 2002

In this paper, data acquisition and analysis of a measuring machine for marine engine's cams is discussed. A rotary encoder and linear scale of the machine to measure angular and linear displacement respectively are interfaced to the PC via encoder board with 2 channels. The design and measuring data are interpolated by cubic spline curves to compute the precision error which is defined by the maximum and minimum distances between two curves. The minimum zone fit of ISO is employed to evaluate the geometric deviation. The developed system takes only 5 minutes to measure and analyze while the CMM takes over 1 hours even with a skilled operator.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1005-1007
• /
• 2005

A Nonlinear approach to control of Small Scale Rotary Wing Unmanned Aerial Vehicle (R-UAV) is presented. Using Backstepping, a globally stabilizing control law is derived. We derive backstepping control law for angle of attack and sideslip control. The inherent nonlinear nature of the system are considered here which helps in naturally stabilizing without extensive external effort. Thus, the resulting control law is much simpler than if the feedback linearization had been used.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.335-340
• /
• 2001

Dynamic stability of a rotary oscillating cantilever beam is presented in this study. Using the stretch deformation instead of the conventional axial deformation, three linear partial differential equations are derived from Hamilton's principle and transformed into dimensionless forms. Stability diagrams of the first order approximate solutions are obtained by using the multiple scale perturbation method. The stability diagrams show that relatively large unstable regions exist near the combination of the first chordwise bending natural frequency and the first stretch natural frequency. This result is verified by using the generalized-${\alpha}$ method.

• 한국정밀공학회지
• /
• 제12권2호
• /
• pp.37-47
• /
• 1995

In recent years, it has been variously developed for testing the accuracy of circular motion of NC machine tools, for example Telescoping Ball Bar Method by Bryan, Circular test Method by Knapp and $r^{-{\theta} }$ Method by Tsutsumi etc., but these methods are all 2-dimentional measuring methods on plane. These simple methods of circular motion accuracy test of NC machine tools have been studied by many reserchers as above, but it is not yet settled in the code of measuring methods of motion errors of NC machine tools, because of errors of measuring units and sensors, and also especially the difficulties of centering of measuring units and the spindle of machining center. In this paper, in use of 2 rotary encoders and 1 magnetic type linear scale with resolution of 0.5 .mu. m, it has become possible for measuring of 3 dimentional space motion accuracy.

• Environmental Engineering Research
• /
• 제19권1호
• /
• pp.47-57
• /
• 2014

The aim of this paper was to study the effect of five different waste combinations (C/N 15, C/N 20, C/N 25, C/N 30, and control) of sewage sludge coupled with sawdust and cattle manure in a pilot scale rotary drum reactor, during 20 days of the composting process. Our results showed that C/N 30 possesses a higher temperature regime with higher % reduction in moisture content, total organic carbon, soluble biochemical oxygen demand and chemical oxygen demand; and higher % gain in total nitrogen and phosphorus at the end of the composting period implying the total amount of biodegradable organic material is stabilized. In addition, $CO_2$ evolution and oxygen uptake rate decreased during the process, reflecting the stable behavior of the final compost. A Solvita maturity index of 8 indicated that the compost was stable and ready for usage as a soil conditioner. The results indicated that composting can be an alternate technology for the management of sewage sludge disposal.